User manual

-15--14-
7. Change Installer Code(administrator password):
The Installer Code is the password to access the door staon debug State. The default
Installer Code is '66666666'. Note that if the Default Set have been acvated, the Installer
Code will be set to default value.
9. Change Unlcok Code:
If door staon runs as Debug State, you can press “1#” to acvate Tools Menu, then
select “2” to enter setup page,then select 4 item.If it runs as Normal State, follow these
steps:
10. User Card Management:
This secon explains how to configure the key fob funcon on DMR18,The key fob is used
to open the lock. Total 1000 key fobs can be registered with one door staon. When
swiping the fob to the door staon, the distance must be less than 3 cenmeter.
Key Fobs must be registered on the Door staon that can be used to open the door.
Register the Key Fobs:
All the registered key fobs are called User Cards/User Key Fobs. New fobs/cards need to
be registered one by one to the Door staon to become a valid User Card/User Key Fob;
and every User Card/User Key Fob is related to a certain Monitor Address (Flat code).
When the Doors taon is standby, press [#] --> [9008] -->Password([66666666 by
default]) to get into the Debug Mode Menu, then Press [1 #] --> [3] Card Manage -->[1]
Add Card to get into the Add Card page. Please see the followings.
8. How to use code unlock funcon:
Please refer to the following operaons:
[ 9 0 0 8 ]
Please Input Password
1 2 3
654
7 8 9
#0
*
1 2 3
654
7 8 9
#0
*
RF CARD
[8017 ]
i
>> Deb u g S t a t e < <
0 -# R e dial
2 -# E x its
1. ID C o d e [ 1 ]
2. Unl o c k Tim i n g[05]
3. Unl o c k O u tpu t[0 ]
4. Car d Memory [ 0 ]
5. Doorpla t e Mod e
6. A u dio Options ...
7. P a r amet ers ...
9. Defaul t
Press1~9
to select
*Back
Installer
Setup
1 -# T ool s
8. Insta ller C o d e...
1. Inst a ller Set u p
2. Set u p
3. Car d Memory
4. O n line Monitors
5. O n line D evice s
6. V o lta g e Measure
Pres NO.
to select
*Back
Tools
*Back
[ - - - - - - - - ]
( * * * * * * * *)
# Save
8. Insta ller C o d e...
In Debug State,
press '1 #' key
press '1' press '8'
Input a new Installer Code
and then press '#' key to
confirm
When the Door Staon is
in standby, Press “#”
Input 4 digits Unlock
Code directly
If verified correctly,
door open
[ 8002 ]
Please Input Password
1. La n g uag e [ 1 ]
2. Tone Sel e ct [ 03]
3. Tone Vo l ume[ 03]
5. Di s pla y Mod e
6. Clock
7. Set u p C o d e
8. Ab out
9. Defaul t
Press No.
to select
*Back
Setup
*Back
[ - - - - ]
( * * * *)
# Save
4. Unl o c k C o d e [ 1111]
4. Unl o c k C o d e [ 1111]
1 2 3
654
7 8 9
#0
*
Press “#”,Input “8002”,
then input Setup Code or
Admin Code(88888888 or
66666666 by default)
Press “4” to enter
unlock code item.
Input 4 digits number,
then press “#” to
update