User manual

Bit-1 to Bit-5 are used for User Code seng.The DT596 responds to 0~15 .
5. DIP Switch Seng
-11--10-
5.1 DIP Switch Sengs of Door Staon
6. Funcons Seng Up
5.2 DIP Switches Sengs of Monitor
ON(1)
=
OFF(0)
=
ON
ON
1
2
3 4
ON
1
2
3 4
ON
1
2
3 4
ON
1
2
3 4
ON
1
2
3 4
ON
1
2
3 4
ON
Total 4 bits on the DIP switches can be configured.The switches can be modified either before or aer installaon.
Seng Item Bit State Descripons
Bit1 and Bit2
(it is used to set
the ID code for
door staon)
Default seng, ID = 0(00), set to the first Door Staon.
ID = 1(10), set to the second Door Staon.
ID = 2(01), set to the third Door Staon.
ID = 3(11), set to the fourth Door Staon.
Bit3
Bit4
Acvate external output seng,the relay 2 terminal doesn't
respond to the second lock and will be closed for 60 seconds
when the "Lockout" is carried out.The alarm connected to
the terminal of relay 2 will be acvated.
inacvate
Reserve
There are 6 bit switches in total. The DIP switches are used to configure the User Code for each Monitor.
Bit-6 is line terminal switch, which needs to be set to ON if the Monitor is in the end of the bus, otherwise set to OFF.
Bit state Seng Bit state Seng
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
The monitor is
not at the end
of the bus.
The monitor is
at the end of
the bus.
BIT STATE USER CODE BIT STATE USER CODE BIT STATE USER CODE
Code=0 Code=6 Code=11
Code=1 Code=7 Code=12
Code=2 Code=8 Code=13
Code=3 Code=9 Code=14
Code=4 Code=10 Code=15
Code=5
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON

This secon explains the sengs of each funcon,please refer to the following table:
About the seng mode:
Input the master code to switch the seng mode, and input the corresponding seng code to perform the
the funcon you want. Aer sengs have been made, input the following seng codes to connue the seng
operaon. Press "
*
" to exit the seng mode.
• The example is set as cancel buon and # as confirm buon,please refer to */# funcon seng
for detail informaon.
• No slide-touching the digital keypad,it may cause mistaken recognion of keys being pressed,
the correct operaon is using your finger to press the digit you desired.
• You should press“confirm”buon aer finish inpung the code number each me,otherwise,
the operaon will be cancelled automacally in 10s.