USER MANUAL (English) VIDEO DOOR PHONE SYSTEM Item No. : 13507, 13508 The design and specifications can be changed without notice to users. Copyright of this manual is reserved. 1 2 3 4 5 6 7 8 9 * 0 # 1 2 3 4 5 6 7 8 9 * 0 # Version2.0.1.1.8.
1.1 Door Station E Camera Lens Speaker 1 2 3 4 5 6 7 8 9 * 0 # Touch Sensitive Digital Keypad 176mm 1. Parts and Functions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 2. Mounting and Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 2.1 Door station Mounting - - - - - - - - - - - - - - - - - - - - - - - - 2 3. Terminal Descriptions - - - - - - - - - - - - - - - - - - - - - - - - - - - 4 4.
2. Mounting and Setting 2.1 Door Station Mounting Door Station E Mounting Door Station F Mounting 1 2 Drill holes in the wall to match the size of screws and attach the rainy guard to the wall. Adjust camera angle Connect the cable correctly and adjust camera to the right angle. 3 4 Attach the panel to the rainy guard. Use the screwdriver and the screw to fix the panel. -2- 1 2 Adjust camera angle Drill holes in the wall to match the size of the mounting box and attach it to the wall.
. System Wiring and Connections 3. Terminal Descriptions 4.
4.3 Electromagnetic Lock Connection 4.3.3 Unlock parameter setting(set in monitor) 4.3.1 Door Lock Controlled by Internal Power Note: 1. Only applicable to the power off to unlock type of electronic locks. 2. The door lock is limited to 12V, and holding current must be less than 250mA. 3. The door lock control is not timed from Exit Button(EB). 4. The Unlock Mode Parameter of Monitor must be set to 1 (by default). 1 2 3 BUS PL S1+ S2+ BUS PL S1+ S2+ 1 ST -- OFF Exit 2. Select Advanced Set...
4.4 Multi Door Stations Connection 4.5 Multi Monitors Connection Basic IN-OUT Wiring Mode Monitors Attention: You must follow the dip switch settings in the table on page 10. So, 1st monitor all switches down, 2nd monitor switch 1 up, 3rd monitor switch 2 up, etc.
5. DIP Switch Setting Bit-1 to Bit-5 are used for User Code setting.The DT596 responds to 0~15 . 5.1 DIP Switch Settings of Door Station ON(1) ON OFF(0) ON = BIT STATE = ON Code=0 1 2 3 4 5 6 Total 4 bits on the DIP switches can be configured.The switches can be modified either before or after installation. Setting Item Bit State Descriptions Default setting, ID = 0(00), set to the first Door Station. 1234 ID = 1(10), set to the second Door Station.
1 2 3 4 5 6 ORDER SETTING ITEMS SETTING RANGE DEFAULT VALUE SETTING CODE 7 8 9 1 Reset all settings 1, 2, 3, 4 - 00 * 0 # 2 Setting the master code 1 - 12 digits Valid keys: 0 - 9 1, 2, 3, 4 01 3 Setting the key illumination time 10 to 99 seconds / permantly lit 10 seconds 02 4 Setting the unlock time 01 to 99 seconds 1 seconds 03 5 Setting the unlock mode 0: opened/ 1: closed opened 04 6 Operation tone settings 0: on/ 1: off on 05 7 Reset code settings 1, 2,
(RED) ON Input the master code. (Default : [ 1 2 3 4 ] +[#] ) (BLUE) OFF (RED) ON Input the master code. (Default : [ 1 2 3 4 ] +[#] ) Beep + , Beep 5. Setting the unlock mode (Default : 0 (opened)) 6. Setting operation tone (Default : ON) 7. Reset code setting 8. *&# function setting (Default : Normal) 9. Call tone setting (Default : enable) 10.Interference resistant grade setting (Default : 2) Input the setting code. 04+# Input the setting code. 05+# Input the setting code.
7. Unlock Operations 7.1 Unlocking user code When the registered user code has been input using the keypad (1~12 digits), the LED indicator (group 1: red, group 2: blue) lights up, the buzzer sounds,and the electric door strike is unlocked. Example : Group 1 2011 (RED) ON Input the master code. (Default : [ 1 2 3 4 ] +[#] ) (BLUE) OFF Red LED lights up (During relay 1 operation) Beep + , Beep (RED) (BLUE) ON OFF 12. Setting the code for Temporary 1 13. Setting the code for Temporary 2 14.
8. Power Supply Instructions NAME DISCRIPTION USAGE PS5-24V Power supply, 85 ~ 260 Vac input, 24 Vdc / 3A output, 10 DIN modules PS4-24V Power supply, 85 ~ 260 Vac input, 24Vdc / 1A output, for basic kit only, 4 DIN modules Connect to multi doorstations or multi monitors (up to 2 or above) Connect to one doorstation and one monitor(DT16 can be connected two) 9. Precaustions • Please clean the unit with soft cotton cloth, don't use the organic impregnant or chemical cleaning agent.
