User's Manual
Table Of Contents
- Cover
- Contents
- 1 Welcome to the Card Personalization System
- 2 Installation Requirements
- 3 Install the System
- 4 Using the System
- 5 Card Design
- 6 System Maintenance
- 7 Troubleshooting
- Tools for Troubleshooting
- Locating the Issue
- Installation Troubleshooting
- Card Appearance
- Magnetic Stripe
- Card Jam
- Messages and Conditions
- Respond to Messages
- Printer Component Messages (100-124)
- 100: Request not supported
- 101: Job could not complete
- 102: Card not in position
- 103: Printer problem
- 104: Critical problem
- 105: Magstripe data error
- 106: Magstripe data not found
- 107: Magstripe read data error
- 108: Magstripe read no data
- 111: Card not picked
- 112: Hopper Empty
- 113: Close cover to continue
- 114: Cover opened during job
- 116: Magstripe not available
- 117: Reader not available
- 120: User paused the printer
- 122: Magnetic stripe format problem
- 123: Insert new card then continue
- 124: Insert same card then continue
- Embosser Component Messages (125-151)
- 125: Emboss critical issue
- 126: Emboss format issue
- 127: Emboss transport error
- 128: Embosser card jam
- 129: Embosser topper jam
- 130: Embosser card entry jam
- 131: Embosser card exit jam
- 132: Embosser card stack full
- 133: Embosser card reject full
- 135: Indent ribbon supplies out
- 136: Indent ribbon break
- 137: Embosser wheel error
- 138: Embosser indent error
- 139: Lost card, open emboss cover
- 140: Embosser not available
- 141: Close emboss cover
- 142: Emboss cover error
- 143: Topper ribbon problem
- 144: Topper ribbon out
- 145: Topper ribbon type problem
- 146: Topper ribbon support err.
- 147: Topper ribbon no tag found
- 149: Option not installed
- Printer Component Messages (100-124)
- 8 Supplies and Parts
- 9 Legal Notices
CE870 Card Personalization System Installation and User Guide 91
Chapter 9: Legal Notices
Please note and heed the WARNING and CAUTION
labels that have been placed on the equipment for
your safety. Please do not attempt to operate or repair
this equipment without adequate training.
Regulatory Compliance
Notice for USA (FCC notice)
This equipment has been tested and found to be within the limits for Class A
computing devices, pursuant to Subpart J of Part 15 of FCC rules, designed to
provide reasonable protection against radio interference in a commercial
environment. This equipment generates, uses, and can radiate radio frequency
energy. If it is not installed and used in accordance with this instruction manual,
it may interfere with radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at their own expense.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Notice for Canada
Section 7.1.3 of RSS-GEN
This Device complies with Industry Canada License-exempt RSS standard(s).
Operation is subject to the following two conditions: 1) this device may not cause
interference, and 2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada RSS standard exemptes de
licence(s). Son fonctionnement est soumis aux deux conditions suivantes: 1) ce
dispositif ne peut causer des interférences, et 2) cet appareil doit accepter toute
interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.