User's Manual
Table Of Contents
- Cover
- Contents
- 1 Welcome to the Card Personalization System
- 2 Installation Requirements
- 3 Install the System
- 4 Using the System
- 5 Card Design
- 6 System Maintenance
- 7 Troubleshooting
- Tools for Troubleshooting
- Locating the Issue
- Installation Troubleshooting
- Card Appearance
- Magnetic Stripe
- Card Jam
- Messages and Conditions
- Respond to Messages
- Printer Component Messages (100-124)
- 100: Request not supported
- 101: Job could not complete
- 102: Card not in position
- 103: Printer problem
- 104: Critical problem
- 105: Magstripe data error
- 106: Magstripe data not found
- 107: Magstripe read data error
- 108: Magstripe read no data
- 111: Card not picked
- 112: Hopper Empty
- 113: Close cover to continue
- 114: Cover opened during job
- 116: Magstripe not available
- 117: Reader not available
- 120: User paused the printer
- 122: Magnetic stripe format problem
- 123: Insert new card then continue
- 124: Insert same card then continue
- Embosser Component Messages (125-151)
- 125: Emboss critical issue
- 126: Emboss format issue
- 127: Emboss transport error
- 128: Embosser card jam
- 129: Embosser topper jam
- 130: Embosser card entry jam
- 131: Embosser card exit jam
- 132: Embosser card stack full
- 133: Embosser card reject full
- 135: Indent ribbon supplies out
- 136: Indent ribbon break
- 137: Embosser wheel error
- 138: Embosser indent error
- 139: Lost card, open emboss cover
- 140: Embosser not available
- 141: Close emboss cover
- 142: Emboss cover error
- 143: Topper ribbon problem
- 144: Topper ribbon out
- 145: Topper ribbon type problem
- 146: Topper ribbon support err.
- 147: Topper ribbon no tag found
- 149: Option not installed
- Printer Component Messages (100-124)
- 8 Supplies and Parts
- 9 Legal Notices
v
102: Card not in position________________________________________________ 73
103: Printer problem____________________________________________________ 73
104: Critical problem ___________________________________________________ 73
105: Magstripe data error ______________________________________________ 73
106: Magstripe data not found _________________________________________ 74
107: Magstripe read data error _________________________________________ 74
108: Magstripe read no data ___________________________________________ 74
111: Card not picked __________________________________________________ 75
112: Hopper Empty_____________________________________________________ 75
113: Close cover to continue ___________________________________________ 75
114: Cover opened during job__________________________________________ 75
116: Magstripe not available ___________________________________________ 75
117: Reader not available ______________________________________________ 75
120: User paused the printer ____________________________________________ 76
122: Magnetic stripe format problem____________________________________ 76
123: Insert new card then continue _____________________________________ 76
124: Insert same card then continue ____________________________________ 76
Embosser Component Messages (125-151)__________________________________ 77
125: Emboss critical issue _______________________________________________ 77
126: Emboss format issue _______________________________________________ 77
127: Emboss transport error _____________________________________________ 77
128: Embosser card jam ________________________________________________ 77
129: Embosser topper jam ______________________________________________ 78
130: Embosser card entry jam___________________________________________ 78
131: Embosser card exit jam ____________________________________________ 78
132: Embosser card stack full ___________________________________________ 79
133: Embosser card reject full ___________________________________________ 79
135: Indent ribbon supplies out _________________________________________ 79
136: Indent ribbon break _______________________________________________ 80
137: Embosser wheel error ______________________________________________ 80
138: Embosser indent error______________________________________________ 80
139: Lost card, open emboss cover _____________________________________ 81
140: Embosser not available ____________________________________________ 81
141: Close emboss cover _______________________________________________ 81
142: Emboss cover error ________________________________________________ 81
143: Topper ribbon problem ____________________________________________ 82
144: Topper ribbon out _________________________________________________ 82
145: Topper ribbon type problem _______________________________________ 82
146: Topper ribbon support err. _________________________________________ 82
147: Topper ribbon no tag found________________________________________ 82
149: Option not installed________________________________________________ 83
Chapter 8: Supplies and Parts _____________________________________________________ 85
Supplies ______________________________________________________________________ 85
Indent Ribbon_____________________________________________________________ 85
Topping Foil _______________________________________________________________ 85