User`s guide

ManualsBrandsEnterasys ManualsComputer equipmentVHSIM2-A6DP

311

312

313

314

315

316

317

318

319

320

Table Of Contents

Title
Notice
Contents
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- A
- B
Figures
Tables
About This Guide
- Using This Guide
- Structure of This Guide
- Related Documents
- Document Conventions
- Typographical and Keystroke Conventions
Introduction
- 1.1 Overview
  - 1.1.1 The Management Agent
  - 1.1.2 In-Band vs. Out-of-Band
- 1.2 Navigating Local Management Screens
- 1.3 Local Management Requirements
- 1.4 Local Management Screen Elements
- 1.5 Local Management Keyboard Conventions
- 1.6 Getting Help
Local Management Requirements
- 2.1 Management Terminal Setup
  - 2.1.1 Console Cable Connection
  - 2.1.2 Management Terminal Setup Parameters
- 2.2 Telnet Connections
- 2.3 Monitoring an Uninterruptible Power Supply
Accessing Local Management
- 3.1 Navigating Local Management Screens
- 3.2 Password Screen
- 3.3 Main Menu Screen
- 3.4 Module Selection Screen
  - 3.4.1 Selecting a Module
- 3.5 Module Menu Screen
- 3.6 Overview of Security Methods
- 3.7 Security Menu Screen
- 3.8 Passwords Screen
  - 3.8.1 Setting the Module Login Password
- 3.9 Radius Configuration Screen
  - 3.9.1 Setting the Last Resort Authentication
  - 3.9.2 Setting the Local and Remote Servers
- 3.10 Name Services Configuration Screen
- 3.11 System Authentication Configuration Screen
- 3.12 EAP (Port) Configuration Screen
- 3.13 EAP Statistics Menu Screen
- 3.14 MAC Port Configuration Screen
- 3.15 MAC Supplicant Configuration Screen
Chassis Menu Screens
- 4.1 Chassis Menu Screen
- 4.2 Chassis Configuration Screen
- 4.3 SNMP Configuration Menu Screen
- 4.4 SNMP Community Names Configuration Screen
  - 4.4.1 Establishing Community Names
- 4.5 SNMP Traps Configuration Screen
  - 4.5.1 Configuring the Trap Table
- 4.6 Chassis Environmental Information Screen
- 4.7 Redirect Configuration Menu Screen (Chassis)
- 4.8 Port Redirect Configuration Screen
  - 4.8.1 Changing Source and Destination Ports
- 4.9 VLAN Redirect Configuration Screen
  - 4.9.1 Changing Source VLAN and Destination Ports
Module Configuration Menu Screens
- 5.1 Module Configuration Menu Screen
- 5.2 General Configuration Screen
- 5.3 SNMP Configuration Menu Screen
- 5.4 SNMP Community Names Configuration Screen
  - 5.4.1 Establishing Community Names
- 5.5 SNMP Traps Configuration Screen
  - 5.5.1 Configuring the Trap Table
- 5.6 Access Control List Screen
  - 5.6.1 Entering IP Addresses
  - 5.6.2 Enable/Disable ACL
- 5.7 System Resources Information Screen
  - 5.7.1 Setting the Reset Peak Switch Utilization
- 5.8 FLASH Download Configuration Screen
Port Configuration Menu Screens
- 6.1 Port Configuration Menu Screen
- 6.2 Ethernet Interface Configuration Screen
- 6.3 Ethernet Port Configuration Screen
  - 6.3.1 Selecting Field Settings
  - 6.3.2 Setting the Advertised Ability
- 6.4 HSIM/VHSIM Configuration Screen
- 6.5 Redirect Configuration Menu Screen
- 6.6 Port Redirect Configuration Screen
  - 6.6.1 Changing Source and Destination Ports
- 6.7 VLAN Redirect Configuration Screen
  - 6.7.1 Changing Source VLAN and Destination Ports
- 6.8 Link Aggregation Screen (802.3ad Main Menu Screen)
- 6.9 Broadcast Suppression Configuration Screen
  - 6.9.1 Setting the Threshold
  - 6.9.2 Setting the Reset Peak
802.1 Configuration Menu Screens
- 7.1 802.1 Configuration Menu Screen
- 7.2 Spanning Tree Configuration Menu Screen
- 7.3 Spanning Tree Configuration Screen
  - 7.3.1 Configuring a VLAN Spanning Tree
- 7.4 Spanning Tree Port Configuration Screen
  - 7.4.1 Enabling/Disabling the Default Spanning Tree Ports
  - 7.4.2 Viewing Status of Spanning Tree Ports
- 7.5 PVST Port Configuration Screen
802.1Q VLAN Configuration Menu Screens
- 8.1 Summary of VLAN Local Management
  - 8.1.1 Preparing for VLAN Configuration
- 8.2 802.1Q VLAN Configuration Menu Screen
- 8.3 Static VLAN Configuration Screen
- 8.4 Static VLAN Egress Configuration Screen
  - 8.4.1 Setting Egress Types on Ports
  - 8.4.2 Displaying the Next Group of Ports
- 8.5 Current VLAN Configuration Screen
- 8.6 Current VLAN Egress Configuration Screen
- 8.7 VLAN Port Configuration Screen
  - 8.7.1 Changing the Port Mode
  - 8.7.2 Configuring the VLAN Ports
- 8.8 VLAN Classification Configuration Screen
- 8.9 Protocol Port Configuration Screen
  - 8.9.1 Assigning Ports to a VID/Classification
802.1p Configuration Menu Screens
- 9.1 802.1p Configuration Menu Screen
- 9.2 Port Priority Configuration Screen
  - 9.2.1 Setting Switch Port Priority Port-by-Port
  - 9.2.2 Setting Switch Port Priority on All Ports
- 9.3 Traffic Class Information Screen
- 9.4 Traffic Class Configuration Screen
  - 9.4.1 Assigning the Traffic Class to Port Priority
- 9.5 Transmit Queues Configuration Screen
  - 9.5.1 Setting the Current Queueing Mode
- 9.6 Priority Classification Configuration Screen
- 9.7 Protocol Port Configuration Screen
  - 9.7.1 Assigning Ports to a PID/Classification
  - 9.7.2 Example, Prioritizing Traffic According to Classification Rule
    - 9.7.2.1 Solving the Problem
- 9.8 Rate Limiting Configuration Screen
Layer 3 Extensions Menu Screens
- 10.1 Layer 3 Extensions Menu Screen
- 10.2 IGMP/VLAN Configuration Screen
  - 10.2.1 IGMP/VLAN Configuration Procedure
Module Statistics Menu Screens
- 11.1 Module Statistics Menu Screen
- 11.2 Switch Statistics Screen
- 11.3 Interface Statistics Screen
  - 11.3.1 Displaying Interface Statistics
- 11.4 RMON Statistics Screen
  - 11.4.1 Displaying RMON Statistics
- 11.5 Chassis Environmental Statistics Configuration Screen
Network Tools Screens
- 12.1 Network Tools
- 12.2 Built-in Commands
- 12.3 Example, Effects of Aging Time on Dynamic Egress
- 12.4 Example, Using Dynamic Egress to Control Traffic
- 12.5 Special Commands
VLAN Operation and Network Applications
- 13.1 Defining VLANs
- 13.2 Types of VLANs
  - 13.2.1 802.1Q VLANs
  - 13.2.2 Other VLAN Strategies
- 13.3 Benefits and Restrictions
- 13.4 VLAN Terms
- 13.5 VLAN Operation
  - 13.5.1 Description
  - 13.5.2 VLAN Components
- 13.6 Configuration Process
- 13.7 VLAN Switch Operation
  - 13.7.1 Receiving Frames from VLAN Ports
  - 13.7.2 Forwarding Decisions
    - 13.7.2.1 Broadcasts, Multicasts, and Unknown Unicasts
    - 13.7.2.2 Known Unicasts
- 13.8 VLAN Configuration
- 13.9 Summary of VLAN Local Management
  - 13.9.1 Preparing for VLAN Configuration
- 13.10 Quick VLAN Walkthrough
- 13.11 Examples
- 13.12 Example 1, Single Switch Operation
  - 13.12.1 Solving the Problem
  - 13.12.2 Frame Handling
- 13.13 Example 2, VLANs Across Multiple Switches
  - 13.13.1 Solving the Problem
  - 13.13.2 Frame Handling
- 13.14 Example 3, Filtering Traffic According to a Layer 4 Classification Rule
  - 13.14.1 Solving the Problem
- 13.15 Example 4, Securing Sensitive Information According to Subnet
  - 13.15.1 Solving the Problem
- 13.16 Example 5, Using Dynamic Egress to Control Traffic
- 13.17 Example 6, Locking a MAC Address to a Port Using Classification Rules
  - 13.17.1 Solving the Problem
Generic Attribute Registration Protocol (GARP)
- A.1 Operation
- A.2 How It Works
About IGMP
- B.1 IGMP Overview
- B.2 Supported Features and Functions
- B.3 Detecting Multicast Routers
Index
- Numerics
- A
- B
- C
- D
- E
- F
- G
- H
- I
- K
- L
- M
- N
- P
- Q
- R
- S
- T
- U
- V
- W

IGMP/VLAN Configuration Screen

Layer 3 Extensions Menu Screens 10-5

Field Descriptions

Table 10-2 describes each field of the IGMP/VLAN Configuration screen:

Table 10-2 IGMP/VLAN Configuration Screen Field Descriptions

Use this field… To…

IGMP Version

(Toggle)

See the current configured IGMP version running on the VLAN

selected in the VLAN ID field (version 1 or 2). The default is version 2.

The IGMP Version field can be toggled to configure the switch in

either version 1 or 2 to match the router configuration. For IGMP to

function correctly, all switches on a LAN must be configured to run the

same version of IGMP. All VLANs available to the switch will be

affected if ALL is chosen as the option under VLAN ID. The field will

initially display an asterisk (*).

Query Interval

(Modifiable)

See or change the query interval time. If the switch is the querier, the

value in the Query Interval field indicates how often IGMP Host-Query

frames are transmitted on the VLAN selected in the VLAN ID field.

This value is also used in calculations for other timers. The default

value is 125 seconds. The range of possible entries is 1 to 300 seconds.

An entry outside of the range will cause the error message

“PERMISSIBLE RANGE: 1...300” to display in the Event Message

field. The field will initially display an asterisk (*).

Query Response

Time

(Modifiable)

Enter the maximum query response time advertised in IGMPv2 general

queries on this VLAN. This value is used in calculations for other

timers. The default value is 10 seconds. The range of possible entries is

1 to 300 seconds. The value entered in this field cannot be bigger than

the Query Interval. The field will initially display an asterisk (*).

Interface

Robustness

(Modifiable)

Tune the expected frame loss on a subnet. If a subnet is expected to be

high loss, the Robustness Variable may be increased. IGMP is robust to

(Robustness Variable-1) packet losses. This value is also used in

calculations for other timers. The default value is 2. The field will

initially display an asterisk (*).

TIP: If the Interface Robustness is adjusted higher than the

default value, depending on the network, this may be an

indication of problems with the network that need to be

resolved.