User`s guide

ManualsBrandsEnterasys ManualsComputer equipmentVHSIM2-A6DP

281

282

283

284

285

286

287

288

289

290

Table Of Contents

Title
Notice
Contents
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- A
- B
Figures
Tables
About This Guide
- Using This Guide
- Structure of This Guide
- Related Documents
- Document Conventions
- Typographical and Keystroke Conventions
Introduction
- 1.1 Overview
  - 1.1.1 The Management Agent
  - 1.1.2 In-Band vs. Out-of-Band
- 1.2 Navigating Local Management Screens
- 1.3 Local Management Requirements
- 1.4 Local Management Screen Elements
- 1.5 Local Management Keyboard Conventions
- 1.6 Getting Help
Local Management Requirements
- 2.1 Management Terminal Setup
  - 2.1.1 Console Cable Connection
  - 2.1.2 Management Terminal Setup Parameters
- 2.2 Telnet Connections
- 2.3 Monitoring an Uninterruptible Power Supply
Accessing Local Management
- 3.1 Navigating Local Management Screens
- 3.2 Password Screen
- 3.3 Main Menu Screen
- 3.4 Module Selection Screen
  - 3.4.1 Selecting a Module
- 3.5 Module Menu Screen
- 3.6 Overview of Security Methods
- 3.7 Security Menu Screen
- 3.8 Passwords Screen
  - 3.8.1 Setting the Module Login Password
- 3.9 Radius Configuration Screen
  - 3.9.1 Setting the Last Resort Authentication
  - 3.9.2 Setting the Local and Remote Servers
- 3.10 Name Services Configuration Screen
- 3.11 System Authentication Configuration Screen
- 3.12 EAP (Port) Configuration Screen
- 3.13 EAP Statistics Menu Screen
- 3.14 MAC Port Configuration Screen
- 3.15 MAC Supplicant Configuration Screen
Chassis Menu Screens
- 4.1 Chassis Menu Screen
- 4.2 Chassis Configuration Screen
- 4.3 SNMP Configuration Menu Screen
- 4.4 SNMP Community Names Configuration Screen
  - 4.4.1 Establishing Community Names
- 4.5 SNMP Traps Configuration Screen
  - 4.5.1 Configuring the Trap Table
- 4.6 Chassis Environmental Information Screen
- 4.7 Redirect Configuration Menu Screen (Chassis)
- 4.8 Port Redirect Configuration Screen
  - 4.8.1 Changing Source and Destination Ports
- 4.9 VLAN Redirect Configuration Screen
  - 4.9.1 Changing Source VLAN and Destination Ports
Module Configuration Menu Screens
- 5.1 Module Configuration Menu Screen
- 5.2 General Configuration Screen
- 5.3 SNMP Configuration Menu Screen
- 5.4 SNMP Community Names Configuration Screen
  - 5.4.1 Establishing Community Names
- 5.5 SNMP Traps Configuration Screen
  - 5.5.1 Configuring the Trap Table
- 5.6 Access Control List Screen
  - 5.6.1 Entering IP Addresses
  - 5.6.2 Enable/Disable ACL
- 5.7 System Resources Information Screen
  - 5.7.1 Setting the Reset Peak Switch Utilization
- 5.8 FLASH Download Configuration Screen
Port Configuration Menu Screens
- 6.1 Port Configuration Menu Screen
- 6.2 Ethernet Interface Configuration Screen
- 6.3 Ethernet Port Configuration Screen
  - 6.3.1 Selecting Field Settings
  - 6.3.2 Setting the Advertised Ability
- 6.4 HSIM/VHSIM Configuration Screen
- 6.5 Redirect Configuration Menu Screen
- 6.6 Port Redirect Configuration Screen
  - 6.6.1 Changing Source and Destination Ports
- 6.7 VLAN Redirect Configuration Screen
  - 6.7.1 Changing Source VLAN and Destination Ports
- 6.8 Link Aggregation Screen (802.3ad Main Menu Screen)
- 6.9 Broadcast Suppression Configuration Screen
  - 6.9.1 Setting the Threshold
  - 6.9.2 Setting the Reset Peak
802.1 Configuration Menu Screens
- 7.1 802.1 Configuration Menu Screen
- 7.2 Spanning Tree Configuration Menu Screen
- 7.3 Spanning Tree Configuration Screen
  - 7.3.1 Configuring a VLAN Spanning Tree
- 7.4 Spanning Tree Port Configuration Screen
  - 7.4.1 Enabling/Disabling the Default Spanning Tree Ports
  - 7.4.2 Viewing Status of Spanning Tree Ports
- 7.5 PVST Port Configuration Screen
802.1Q VLAN Configuration Menu Screens
- 8.1 Summary of VLAN Local Management
  - 8.1.1 Preparing for VLAN Configuration
- 8.2 802.1Q VLAN Configuration Menu Screen
- 8.3 Static VLAN Configuration Screen
- 8.4 Static VLAN Egress Configuration Screen
  - 8.4.1 Setting Egress Types on Ports
  - 8.4.2 Displaying the Next Group of Ports
- 8.5 Current VLAN Configuration Screen
- 8.6 Current VLAN Egress Configuration Screen
- 8.7 VLAN Port Configuration Screen
  - 8.7.1 Changing the Port Mode
  - 8.7.2 Configuring the VLAN Ports
- 8.8 VLAN Classification Configuration Screen
- 8.9 Protocol Port Configuration Screen
  - 8.9.1 Assigning Ports to a VID/Classification
802.1p Configuration Menu Screens
- 9.1 802.1p Configuration Menu Screen
- 9.2 Port Priority Configuration Screen
  - 9.2.1 Setting Switch Port Priority Port-by-Port
  - 9.2.2 Setting Switch Port Priority on All Ports
- 9.3 Traffic Class Information Screen
- 9.4 Traffic Class Configuration Screen
  - 9.4.1 Assigning the Traffic Class to Port Priority
- 9.5 Transmit Queues Configuration Screen
  - 9.5.1 Setting the Current Queueing Mode
- 9.6 Priority Classification Configuration Screen
- 9.7 Protocol Port Configuration Screen
  - 9.7.1 Assigning Ports to a PID/Classification
  - 9.7.2 Example, Prioritizing Traffic According to Classification Rule
    - 9.7.2.1 Solving the Problem
- 9.8 Rate Limiting Configuration Screen
Layer 3 Extensions Menu Screens
- 10.1 Layer 3 Extensions Menu Screen
- 10.2 IGMP/VLAN Configuration Screen
  - 10.2.1 IGMP/VLAN Configuration Procedure
Module Statistics Menu Screens
- 11.1 Module Statistics Menu Screen
- 11.2 Switch Statistics Screen
- 11.3 Interface Statistics Screen
  - 11.3.1 Displaying Interface Statistics
- 11.4 RMON Statistics Screen
  - 11.4.1 Displaying RMON Statistics
- 11.5 Chassis Environmental Statistics Configuration Screen
Network Tools Screens
- 12.1 Network Tools
- 12.2 Built-in Commands
- 12.3 Example, Effects of Aging Time on Dynamic Egress
- 12.4 Example, Using Dynamic Egress to Control Traffic
- 12.5 Special Commands
VLAN Operation and Network Applications
- 13.1 Defining VLANs
- 13.2 Types of VLANs
  - 13.2.1 802.1Q VLANs
  - 13.2.2 Other VLAN Strategies
- 13.3 Benefits and Restrictions
- 13.4 VLAN Terms
- 13.5 VLAN Operation
  - 13.5.1 Description
  - 13.5.2 VLAN Components
- 13.6 Configuration Process
- 13.7 VLAN Switch Operation
  - 13.7.1 Receiving Frames from VLAN Ports
  - 13.7.2 Forwarding Decisions
    - 13.7.2.1 Broadcasts, Multicasts, and Unknown Unicasts
    - 13.7.2.2 Known Unicasts
- 13.8 VLAN Configuration
- 13.9 Summary of VLAN Local Management
  - 13.9.1 Preparing for VLAN Configuration
- 13.10 Quick VLAN Walkthrough
- 13.11 Examples
- 13.12 Example 1, Single Switch Operation
  - 13.12.1 Solving the Problem
  - 13.12.2 Frame Handling
- 13.13 Example 2, VLANs Across Multiple Switches
  - 13.13.1 Solving the Problem
  - 13.13.2 Frame Handling
- 13.14 Example 3, Filtering Traffic According to a Layer 4 Classification Rule
  - 13.14.1 Solving the Problem
- 13.15 Example 4, Securing Sensitive Information According to Subnet
  - 13.15.1 Solving the Problem
- 13.16 Example 5, Using Dynamic Egress to Control Traffic
- 13.17 Example 6, Locking a MAC Address to a Port Using Classification Rules
  - 13.17.1 Solving the Problem
Generic Attribute Registration Protocol (GARP)
- A.1 Operation
- A.2 How It Works
About IGMP
- B.1 IGMP Overview
- B.2 Supported Features and Functions
- B.3 Detecting Multicast Routers
Index
- Numerics
- A
- B
- C
- D
- E
- F
- G
- H
- I
- K
- L
- M
- N
- P
- Q
- R
- S
- T
- U
- V
- W

Transmit Queues Configuration Screen

802.1p Configuration Menu Screens 9-15

9.5.1 Setting the Current Queueing Mode

To set the current queueing mode for a particular port, proceed as follows:

1. Use the arrow keys to highlight the Port field.

2. Press the SPACE bar to step to the appropriate port number. The port type displays to the right

of the Port number field.

3. Use the arrow keys to highlight the Current Queueing Mode field.

4. To select the Current Queueing Mode for the port selected in step 1, press the SPACE bar to

toggle to either STRICT 802.1 or WEIGHTED. The default is STRICT 802.1.

If STRICT 802.1 is selected, the frames will be transmitted out the selected port according to the

frame transmit priority queue set in the Advanced Priority Configuration screen. The weight

priority transmit queue fields, Q0 through Q3, do not display. Go to step 8 to save the setting.

If WEIGHTED is selected, the weight priority transmit queue fields, Q0 through Q3, display.

The frames will be transmitted out the port according to the percent of transmit capacity

allocated for each transmit queue. The default percentages are 25% for each transmit queue (Q0

through Q3). To set the priority transmit queue fields, go to step 5.

5. Use the arrow keys to highlight the Q0 field.

6. Use the SPACE bar to step to the appropriate percent value for the priority transmit queue, Q0.

Q0 is the lowest priority transmit queue. Repeat this step for Q1, Q2, and Q3.

7. To save the settings so they apply to the port selected in step 1, go to step 8. To save the settings

so they apply to all available ports, proceed to step 9.

8. Use the arrow keys to highlight the SAVE command at the bottom of the screen. Then press

ENTER. The message “SAVED OK” displays and the settings are saved for the port selected in

step 1.

9. Use the arrow keys to highlight the SET ALL PORTS command. Then press ENTER. The

message “SAVED OK” displays and the settings are saved for available ports.

TIP: To display the current port settings, press ENTER after selecting the port number.

NOTE: Total percentage of transmit queues Q0 through Q3 must add up to 100% or the

values cannot be saved.

For example: Q0, 0%+ Q1, 25% + Q2, 25% + Q3, 50% = 100%