User`s guide

ManualsBrandsEnterasys ManualsComputer equipmentVHSIM2-A6DP

241

242

243

244

245

246

247

248

249

250

Table Of Contents

Title
Notice
Contents
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- A
- B
Figures
Tables
About This Guide
- Using This Guide
- Structure of This Guide
- Related Documents
- Document Conventions
- Typographical and Keystroke Conventions
Introduction
- 1.1 Overview
  - 1.1.1 The Management Agent
  - 1.1.2 In-Band vs. Out-of-Band
- 1.2 Navigating Local Management Screens
- 1.3 Local Management Requirements
- 1.4 Local Management Screen Elements
- 1.5 Local Management Keyboard Conventions
- 1.6 Getting Help
Local Management Requirements
- 2.1 Management Terminal Setup
  - 2.1.1 Console Cable Connection
  - 2.1.2 Management Terminal Setup Parameters
- 2.2 Telnet Connections
- 2.3 Monitoring an Uninterruptible Power Supply
Accessing Local Management
- 3.1 Navigating Local Management Screens
- 3.2 Password Screen
- 3.3 Main Menu Screen
- 3.4 Module Selection Screen
  - 3.4.1 Selecting a Module
- 3.5 Module Menu Screen
- 3.6 Overview of Security Methods
- 3.7 Security Menu Screen
- 3.8 Passwords Screen
  - 3.8.1 Setting the Module Login Password
- 3.9 Radius Configuration Screen
  - 3.9.1 Setting the Last Resort Authentication
  - 3.9.2 Setting the Local and Remote Servers
- 3.10 Name Services Configuration Screen
- 3.11 System Authentication Configuration Screen
- 3.12 EAP (Port) Configuration Screen
- 3.13 EAP Statistics Menu Screen
- 3.14 MAC Port Configuration Screen
- 3.15 MAC Supplicant Configuration Screen
Chassis Menu Screens
- 4.1 Chassis Menu Screen
- 4.2 Chassis Configuration Screen
- 4.3 SNMP Configuration Menu Screen
- 4.4 SNMP Community Names Configuration Screen
  - 4.4.1 Establishing Community Names
- 4.5 SNMP Traps Configuration Screen
  - 4.5.1 Configuring the Trap Table
- 4.6 Chassis Environmental Information Screen
- 4.7 Redirect Configuration Menu Screen (Chassis)
- 4.8 Port Redirect Configuration Screen
  - 4.8.1 Changing Source and Destination Ports
- 4.9 VLAN Redirect Configuration Screen
  - 4.9.1 Changing Source VLAN and Destination Ports
Module Configuration Menu Screens
- 5.1 Module Configuration Menu Screen
- 5.2 General Configuration Screen
- 5.3 SNMP Configuration Menu Screen
- 5.4 SNMP Community Names Configuration Screen
  - 5.4.1 Establishing Community Names
- 5.5 SNMP Traps Configuration Screen
  - 5.5.1 Configuring the Trap Table
- 5.6 Access Control List Screen
  - 5.6.1 Entering IP Addresses
  - 5.6.2 Enable/Disable ACL
- 5.7 System Resources Information Screen
  - 5.7.1 Setting the Reset Peak Switch Utilization
- 5.8 FLASH Download Configuration Screen
Port Configuration Menu Screens
- 6.1 Port Configuration Menu Screen
- 6.2 Ethernet Interface Configuration Screen
- 6.3 Ethernet Port Configuration Screen
  - 6.3.1 Selecting Field Settings
  - 6.3.2 Setting the Advertised Ability
- 6.4 HSIM/VHSIM Configuration Screen
- 6.5 Redirect Configuration Menu Screen
- 6.6 Port Redirect Configuration Screen
  - 6.6.1 Changing Source and Destination Ports
- 6.7 VLAN Redirect Configuration Screen
  - 6.7.1 Changing Source VLAN and Destination Ports
- 6.8 Link Aggregation Screen (802.3ad Main Menu Screen)
- 6.9 Broadcast Suppression Configuration Screen
  - 6.9.1 Setting the Threshold
  - 6.9.2 Setting the Reset Peak
802.1 Configuration Menu Screens
- 7.1 802.1 Configuration Menu Screen
- 7.2 Spanning Tree Configuration Menu Screen
- 7.3 Spanning Tree Configuration Screen
  - 7.3.1 Configuring a VLAN Spanning Tree
- 7.4 Spanning Tree Port Configuration Screen
  - 7.4.1 Enabling/Disabling the Default Spanning Tree Ports
  - 7.4.2 Viewing Status of Spanning Tree Ports
- 7.5 PVST Port Configuration Screen
802.1Q VLAN Configuration Menu Screens
- 8.1 Summary of VLAN Local Management
  - 8.1.1 Preparing for VLAN Configuration
- 8.2 802.1Q VLAN Configuration Menu Screen
- 8.3 Static VLAN Configuration Screen
- 8.4 Static VLAN Egress Configuration Screen
  - 8.4.1 Setting Egress Types on Ports
  - 8.4.2 Displaying the Next Group of Ports
- 8.5 Current VLAN Configuration Screen
- 8.6 Current VLAN Egress Configuration Screen
- 8.7 VLAN Port Configuration Screen
  - 8.7.1 Changing the Port Mode
  - 8.7.2 Configuring the VLAN Ports
- 8.8 VLAN Classification Configuration Screen
- 8.9 Protocol Port Configuration Screen
  - 8.9.1 Assigning Ports to a VID/Classification
802.1p Configuration Menu Screens
- 9.1 802.1p Configuration Menu Screen
- 9.2 Port Priority Configuration Screen
  - 9.2.1 Setting Switch Port Priority Port-by-Port
  - 9.2.2 Setting Switch Port Priority on All Ports
- 9.3 Traffic Class Information Screen
- 9.4 Traffic Class Configuration Screen
  - 9.4.1 Assigning the Traffic Class to Port Priority
- 9.5 Transmit Queues Configuration Screen
  - 9.5.1 Setting the Current Queueing Mode
- 9.6 Priority Classification Configuration Screen
- 9.7 Protocol Port Configuration Screen
  - 9.7.1 Assigning Ports to a PID/Classification
  - 9.7.2 Example, Prioritizing Traffic According to Classification Rule
    - 9.7.2.1 Solving the Problem
- 9.8 Rate Limiting Configuration Screen
Layer 3 Extensions Menu Screens
- 10.1 Layer 3 Extensions Menu Screen
- 10.2 IGMP/VLAN Configuration Screen
  - 10.2.1 IGMP/VLAN Configuration Procedure
Module Statistics Menu Screens
- 11.1 Module Statistics Menu Screen
- 11.2 Switch Statistics Screen
- 11.3 Interface Statistics Screen
  - 11.3.1 Displaying Interface Statistics
- 11.4 RMON Statistics Screen
  - 11.4.1 Displaying RMON Statistics
- 11.5 Chassis Environmental Statistics Configuration Screen
Network Tools Screens
- 12.1 Network Tools
- 12.2 Built-in Commands
- 12.3 Example, Effects of Aging Time on Dynamic Egress
- 12.4 Example, Using Dynamic Egress to Control Traffic
- 12.5 Special Commands
VLAN Operation and Network Applications
- 13.1 Defining VLANs
- 13.2 Types of VLANs
  - 13.2.1 802.1Q VLANs
  - 13.2.2 Other VLAN Strategies
- 13.3 Benefits and Restrictions
- 13.4 VLAN Terms
- 13.5 VLAN Operation
  - 13.5.1 Description
  - 13.5.2 VLAN Components
- 13.6 Configuration Process
- 13.7 VLAN Switch Operation
  - 13.7.1 Receiving Frames from VLAN Ports
  - 13.7.2 Forwarding Decisions
    - 13.7.2.1 Broadcasts, Multicasts, and Unknown Unicasts
    - 13.7.2.2 Known Unicasts
- 13.8 VLAN Configuration
- 13.9 Summary of VLAN Local Management
  - 13.9.1 Preparing for VLAN Configuration
- 13.10 Quick VLAN Walkthrough
- 13.11 Examples
- 13.12 Example 1, Single Switch Operation
  - 13.12.1 Solving the Problem
  - 13.12.2 Frame Handling
- 13.13 Example 2, VLANs Across Multiple Switches
  - 13.13.1 Solving the Problem
  - 13.13.2 Frame Handling
- 13.14 Example 3, Filtering Traffic According to a Layer 4 Classification Rule
  - 13.14.1 Solving the Problem
- 13.15 Example 4, Securing Sensitive Information According to Subnet
  - 13.15.1 Solving the Problem
- 13.16 Example 5, Using Dynamic Egress to Control Traffic
- 13.17 Example 6, Locking a MAC Address to a Port Using Classification Rules
  - 13.17.1 Solving the Problem
Generic Attribute Registration Protocol (GARP)
- A.1 Operation
- A.2 How It Works
About IGMP
- B.1 IGMP Overview
- B.2 Supported Features and Functions
- B.3 Detecting Multicast Routers
Index
- Numerics
- A
- B
- C
- D
- E
- F
- G
- H
- I
- K
- L
- M
- N
- P
- Q
- R
- S
- T
- U
- V
- W

VLAN Port Configuration Screen

8-20 802.1Q VLAN Configuration Menu Screens

8.7.1 Changing the Port Mode

To change the operational mode of a port, proceed as follows.

1. Use the arrow keys to highlight the Port Mode field for the module and port combination you

wish to change.

2. Use the SPACE bar or BACKSPACE key to step through the available selections. A port may

be configured for any of the following modes:

• HYBRID – This is the default mode for all ports on the switch. The initial Port VLAN List

includes the PVID with a frame format of untagged. Any other VLANs desired for the Port

VLAN List need to be manually configured. By changing the default mode to 1Q Trunk or

1D Trunk, the Port VLAN List and the associated frame type are automatically configured.

• 1Q TRUNK – This mode sets the port for transmitting to another 802.1Q aware device. In

this mode, all frames are transmitted with a tag header included in the frame (excluding

BPDUs). The switch will drop all untagged frames it receives on the 1Q Trunk port. The Port

VLAN List for the port includes all VLANs.

• 1D TRUNK – This mode sets the port for transmitting to a legacy 802.1D switch fabric. In

this mode, all incoming frames are classified into the default VLAN and all frames are

transmitted untagged. The switch expects to receive only untagged frames through the

1D Trunk port. This mode also updates the Port VLAN List and makes the port eligible to

transmit frames for all VLANs.

3. When the desired operational mode for the port is displayed, use the arrow keys to highlight the

SAVE command at the bottom of the screen.

4. Press ENTER. The message “SAVED OK” displays.

Ingress Filtering

(Toggle)

Enable or disable the ingress filtering on a port.

When ENABLED, the module will discard the incoming frames for

VLANs which do not include this Port in its Member set. When

DISABLED, the port will forward the frames.

This control does not affect VLAN independent BPDU frames, such as

GVRP and STP. It does affect VLAN dependent BPDU frames.

GVRP Status

(Toggle)

Enable or disable a port to support dynamic VLANs created by the

GARP VLAN Registration Protocol (GVRP). For more information

about GVRP, refer to Appendix A.

Table 8-6 VLAN Port Configuration Screen Field Descriptions (Continued)

Use this field… To…