User`s guide

ManualsBrandsEnterasys ManualsComputer equipmentVHSIM2-A6DP

231

232

233

234

235

236

237

238

239

240

Table Of Contents

Title
Notice
Contents
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- A
- B
Figures
Tables
About This Guide
- Using This Guide
- Structure of This Guide
- Related Documents
- Document Conventions
- Typographical and Keystroke Conventions
Introduction
- 1.1 Overview
  - 1.1.1 The Management Agent
  - 1.1.2 In-Band vs. Out-of-Band
- 1.2 Navigating Local Management Screens
- 1.3 Local Management Requirements
- 1.4 Local Management Screen Elements
- 1.5 Local Management Keyboard Conventions
- 1.6 Getting Help
Local Management Requirements
- 2.1 Management Terminal Setup
  - 2.1.1 Console Cable Connection
  - 2.1.2 Management Terminal Setup Parameters
- 2.2 Telnet Connections
- 2.3 Monitoring an Uninterruptible Power Supply
Accessing Local Management
- 3.1 Navigating Local Management Screens
- 3.2 Password Screen
- 3.3 Main Menu Screen
- 3.4 Module Selection Screen
  - 3.4.1 Selecting a Module
- 3.5 Module Menu Screen
- 3.6 Overview of Security Methods
- 3.7 Security Menu Screen
- 3.8 Passwords Screen
  - 3.8.1 Setting the Module Login Password
- 3.9 Radius Configuration Screen
  - 3.9.1 Setting the Last Resort Authentication
  - 3.9.2 Setting the Local and Remote Servers
- 3.10 Name Services Configuration Screen
- 3.11 System Authentication Configuration Screen
- 3.12 EAP (Port) Configuration Screen
- 3.13 EAP Statistics Menu Screen
- 3.14 MAC Port Configuration Screen
- 3.15 MAC Supplicant Configuration Screen
Chassis Menu Screens
- 4.1 Chassis Menu Screen
- 4.2 Chassis Configuration Screen
- 4.3 SNMP Configuration Menu Screen
- 4.4 SNMP Community Names Configuration Screen
  - 4.4.1 Establishing Community Names
- 4.5 SNMP Traps Configuration Screen
  - 4.5.1 Configuring the Trap Table
- 4.6 Chassis Environmental Information Screen
- 4.7 Redirect Configuration Menu Screen (Chassis)
- 4.8 Port Redirect Configuration Screen
  - 4.8.1 Changing Source and Destination Ports
- 4.9 VLAN Redirect Configuration Screen
  - 4.9.1 Changing Source VLAN and Destination Ports
Module Configuration Menu Screens
- 5.1 Module Configuration Menu Screen
- 5.2 General Configuration Screen
- 5.3 SNMP Configuration Menu Screen
- 5.4 SNMP Community Names Configuration Screen
  - 5.4.1 Establishing Community Names
- 5.5 SNMP Traps Configuration Screen
  - 5.5.1 Configuring the Trap Table
- 5.6 Access Control List Screen
  - 5.6.1 Entering IP Addresses
  - 5.6.2 Enable/Disable ACL
- 5.7 System Resources Information Screen
  - 5.7.1 Setting the Reset Peak Switch Utilization
- 5.8 FLASH Download Configuration Screen
Port Configuration Menu Screens
- 6.1 Port Configuration Menu Screen
- 6.2 Ethernet Interface Configuration Screen
- 6.3 Ethernet Port Configuration Screen
  - 6.3.1 Selecting Field Settings
  - 6.3.2 Setting the Advertised Ability
- 6.4 HSIM/VHSIM Configuration Screen
- 6.5 Redirect Configuration Menu Screen
- 6.6 Port Redirect Configuration Screen
  - 6.6.1 Changing Source and Destination Ports
- 6.7 VLAN Redirect Configuration Screen
  - 6.7.1 Changing Source VLAN and Destination Ports
- 6.8 Link Aggregation Screen (802.3ad Main Menu Screen)
- 6.9 Broadcast Suppression Configuration Screen
  - 6.9.1 Setting the Threshold
  - 6.9.2 Setting the Reset Peak
802.1 Configuration Menu Screens
- 7.1 802.1 Configuration Menu Screen
- 7.2 Spanning Tree Configuration Menu Screen
- 7.3 Spanning Tree Configuration Screen
  - 7.3.1 Configuring a VLAN Spanning Tree
- 7.4 Spanning Tree Port Configuration Screen
  - 7.4.1 Enabling/Disabling the Default Spanning Tree Ports
  - 7.4.2 Viewing Status of Spanning Tree Ports
- 7.5 PVST Port Configuration Screen
802.1Q VLAN Configuration Menu Screens
- 8.1 Summary of VLAN Local Management
  - 8.1.1 Preparing for VLAN Configuration
- 8.2 802.1Q VLAN Configuration Menu Screen
- 8.3 Static VLAN Configuration Screen
- 8.4 Static VLAN Egress Configuration Screen
  - 8.4.1 Setting Egress Types on Ports
  - 8.4.2 Displaying the Next Group of Ports
- 8.5 Current VLAN Configuration Screen
- 8.6 Current VLAN Egress Configuration Screen
- 8.7 VLAN Port Configuration Screen
  - 8.7.1 Changing the Port Mode
  - 8.7.2 Configuring the VLAN Ports
- 8.8 VLAN Classification Configuration Screen
- 8.9 Protocol Port Configuration Screen
  - 8.9.1 Assigning Ports to a VID/Classification
802.1p Configuration Menu Screens
- 9.1 802.1p Configuration Menu Screen
- 9.2 Port Priority Configuration Screen
  - 9.2.1 Setting Switch Port Priority Port-by-Port
  - 9.2.2 Setting Switch Port Priority on All Ports
- 9.3 Traffic Class Information Screen
- 9.4 Traffic Class Configuration Screen
  - 9.4.1 Assigning the Traffic Class to Port Priority
- 9.5 Transmit Queues Configuration Screen
  - 9.5.1 Setting the Current Queueing Mode
- 9.6 Priority Classification Configuration Screen
- 9.7 Protocol Port Configuration Screen
  - 9.7.1 Assigning Ports to a PID/Classification
  - 9.7.2 Example, Prioritizing Traffic According to Classification Rule
    - 9.7.2.1 Solving the Problem
- 9.8 Rate Limiting Configuration Screen
Layer 3 Extensions Menu Screens
- 10.1 Layer 3 Extensions Menu Screen
- 10.2 IGMP/VLAN Configuration Screen
  - 10.2.1 IGMP/VLAN Configuration Procedure
Module Statistics Menu Screens
- 11.1 Module Statistics Menu Screen
- 11.2 Switch Statistics Screen
- 11.3 Interface Statistics Screen
  - 11.3.1 Displaying Interface Statistics
- 11.4 RMON Statistics Screen
  - 11.4.1 Displaying RMON Statistics
- 11.5 Chassis Environmental Statistics Configuration Screen
Network Tools Screens
- 12.1 Network Tools
- 12.2 Built-in Commands
- 12.3 Example, Effects of Aging Time on Dynamic Egress
- 12.4 Example, Using Dynamic Egress to Control Traffic
- 12.5 Special Commands
VLAN Operation and Network Applications
- 13.1 Defining VLANs
- 13.2 Types of VLANs
  - 13.2.1 802.1Q VLANs
  - 13.2.2 Other VLAN Strategies
- 13.3 Benefits and Restrictions
- 13.4 VLAN Terms
- 13.5 VLAN Operation
  - 13.5.1 Description
  - 13.5.2 VLAN Components
- 13.6 Configuration Process
- 13.7 VLAN Switch Operation
  - 13.7.1 Receiving Frames from VLAN Ports
  - 13.7.2 Forwarding Decisions
    - 13.7.2.1 Broadcasts, Multicasts, and Unknown Unicasts
    - 13.7.2.2 Known Unicasts
- 13.8 VLAN Configuration
- 13.9 Summary of VLAN Local Management
  - 13.9.1 Preparing for VLAN Configuration
- 13.10 Quick VLAN Walkthrough
- 13.11 Examples
- 13.12 Example 1, Single Switch Operation
  - 13.12.1 Solving the Problem
  - 13.12.2 Frame Handling
- 13.13 Example 2, VLANs Across Multiple Switches
  - 13.13.1 Solving the Problem
  - 13.13.2 Frame Handling
- 13.14 Example 3, Filtering Traffic According to a Layer 4 Classification Rule
  - 13.14.1 Solving the Problem
- 13.15 Example 4, Securing Sensitive Information According to Subnet
  - 13.15.1 Solving the Problem
- 13.16 Example 5, Using Dynamic Egress to Control Traffic
- 13.17 Example 6, Locking a MAC Address to a Port Using Classification Rules
  - 13.17.1 Solving the Problem
Generic Attribute Registration Protocol (GARP)
- A.1 Operation
- A.2 How It Works
About IGMP
- B.1 IGMP Overview
- B.2 Supported Features and Functions
- B.3 Detecting Multicast Routers
Index
- Numerics
- A
- B
- C
- D
- E
- F
- G
- H
- I
- K
- L
- M
- N
- P
- Q
- R
- S
- T
- U
- V
- W

Static VLAN Configuration Screen

802.1Q VLAN Configuration Menu Screens 8-9

8.3.3 Renaming a Static VLAN

To change the name of an existing VLAN, proceed as follows:

1. Use the arrow keys to highlight the VLAN ID field near the bottom of the screen.

2. Type the VLAN ID number of the VLAN to be changed. Press ENTER.

3. Use the arrow keys to highlight the VLAN Name field near the bottom of the screen.

4. Type the new VLAN name of up to 32 ASCII characters in the VLAN Name field.

5. Press ENTER.

6. Use the arrow keys to highlight the ADD field and press ENTER. The new name is now

displayed.

8.3.4 Deleting a Static VLAN

To delete a VLAN from the VLAN list, proceed as follows:

1. Use the arrow keys to highlight the line containing the

VLAN ID, FDB ID, and VLAN Name

information. The following message is displayed at the top of the screen:

“Hit <RETURN> key to edit port list, or <M> to mark.”

2. Press the M (not case sensitive) key, and an asterisk (*) appears to the left of the highlighted line.

If more than one VLAN is to be deleted, repeat steps 1 and 2 to highlight and mark each line.

Otherwise, go to step 4.

3. After the lines are marked, use the arrow keys to highlight the DEL MARKED command.

4. Press ENTER. The VLANs and marked line items are deleted from the list.

NOTE: The default VLAN cannot be deleted from the list.

NOTE: If for some reason you want to remove a mark, perform steps 1 and 2 to mark

the line. Then press M to delete the mark.