User`s guide

ManualsBrandsEnterasys ManualsComputer equipmentVHSIM2-A6DP

121

122

123

124

125

126

127

128

129

130

Table Of Contents

Title
Notice
Contents
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- A
- B
Figures
Tables
About This Guide
- Using This Guide
- Structure of This Guide
- Related Documents
- Document Conventions
- Typographical and Keystroke Conventions
Introduction
- 1.1 Overview
  - 1.1.1 The Management Agent
  - 1.1.2 In-Band vs. Out-of-Band
- 1.2 Navigating Local Management Screens
- 1.3 Local Management Requirements
- 1.4 Local Management Screen Elements
- 1.5 Local Management Keyboard Conventions
- 1.6 Getting Help
Local Management Requirements
- 2.1 Management Terminal Setup
  - 2.1.1 Console Cable Connection
  - 2.1.2 Management Terminal Setup Parameters
- 2.2 Telnet Connections
- 2.3 Monitoring an Uninterruptible Power Supply
Accessing Local Management
- 3.1 Navigating Local Management Screens
- 3.2 Password Screen
- 3.3 Main Menu Screen
- 3.4 Module Selection Screen
  - 3.4.1 Selecting a Module
- 3.5 Module Menu Screen
- 3.6 Overview of Security Methods
- 3.7 Security Menu Screen
- 3.8 Passwords Screen
  - 3.8.1 Setting the Module Login Password
- 3.9 Radius Configuration Screen
  - 3.9.1 Setting the Last Resort Authentication
  - 3.9.2 Setting the Local and Remote Servers
- 3.10 Name Services Configuration Screen
- 3.11 System Authentication Configuration Screen
- 3.12 EAP (Port) Configuration Screen
- 3.13 EAP Statistics Menu Screen
- 3.14 MAC Port Configuration Screen
- 3.15 MAC Supplicant Configuration Screen
Chassis Menu Screens
- 4.1 Chassis Menu Screen
- 4.2 Chassis Configuration Screen
- 4.3 SNMP Configuration Menu Screen
- 4.4 SNMP Community Names Configuration Screen
  - 4.4.1 Establishing Community Names
- 4.5 SNMP Traps Configuration Screen
  - 4.5.1 Configuring the Trap Table
- 4.6 Chassis Environmental Information Screen
- 4.7 Redirect Configuration Menu Screen (Chassis)
- 4.8 Port Redirect Configuration Screen
  - 4.8.1 Changing Source and Destination Ports
- 4.9 VLAN Redirect Configuration Screen
  - 4.9.1 Changing Source VLAN and Destination Ports
Module Configuration Menu Screens
- 5.1 Module Configuration Menu Screen
- 5.2 General Configuration Screen
- 5.3 SNMP Configuration Menu Screen
- 5.4 SNMP Community Names Configuration Screen
  - 5.4.1 Establishing Community Names
- 5.5 SNMP Traps Configuration Screen
  - 5.5.1 Configuring the Trap Table
- 5.6 Access Control List Screen
  - 5.6.1 Entering IP Addresses
  - 5.6.2 Enable/Disable ACL
- 5.7 System Resources Information Screen
  - 5.7.1 Setting the Reset Peak Switch Utilization
- 5.8 FLASH Download Configuration Screen
Port Configuration Menu Screens
- 6.1 Port Configuration Menu Screen
- 6.2 Ethernet Interface Configuration Screen
- 6.3 Ethernet Port Configuration Screen
  - 6.3.1 Selecting Field Settings
  - 6.3.2 Setting the Advertised Ability
- 6.4 HSIM/VHSIM Configuration Screen
- 6.5 Redirect Configuration Menu Screen
- 6.6 Port Redirect Configuration Screen
  - 6.6.1 Changing Source and Destination Ports
- 6.7 VLAN Redirect Configuration Screen
  - 6.7.1 Changing Source VLAN and Destination Ports
- 6.8 Link Aggregation Screen (802.3ad Main Menu Screen)
- 6.9 Broadcast Suppression Configuration Screen
  - 6.9.1 Setting the Threshold
  - 6.9.2 Setting the Reset Peak
802.1 Configuration Menu Screens
- 7.1 802.1 Configuration Menu Screen
- 7.2 Spanning Tree Configuration Menu Screen
- 7.3 Spanning Tree Configuration Screen
  - 7.3.1 Configuring a VLAN Spanning Tree
- 7.4 Spanning Tree Port Configuration Screen
  - 7.4.1 Enabling/Disabling the Default Spanning Tree Ports
  - 7.4.2 Viewing Status of Spanning Tree Ports
- 7.5 PVST Port Configuration Screen
802.1Q VLAN Configuration Menu Screens
- 8.1 Summary of VLAN Local Management
  - 8.1.1 Preparing for VLAN Configuration
- 8.2 802.1Q VLAN Configuration Menu Screen
- 8.3 Static VLAN Configuration Screen
- 8.4 Static VLAN Egress Configuration Screen
  - 8.4.1 Setting Egress Types on Ports
  - 8.4.2 Displaying the Next Group of Ports
- 8.5 Current VLAN Configuration Screen
- 8.6 Current VLAN Egress Configuration Screen
- 8.7 VLAN Port Configuration Screen
  - 8.7.1 Changing the Port Mode
  - 8.7.2 Configuring the VLAN Ports
- 8.8 VLAN Classification Configuration Screen
- 8.9 Protocol Port Configuration Screen
  - 8.9.1 Assigning Ports to a VID/Classification
802.1p Configuration Menu Screens
- 9.1 802.1p Configuration Menu Screen
- 9.2 Port Priority Configuration Screen
  - 9.2.1 Setting Switch Port Priority Port-by-Port
  - 9.2.2 Setting Switch Port Priority on All Ports
- 9.3 Traffic Class Information Screen
- 9.4 Traffic Class Configuration Screen
  - 9.4.1 Assigning the Traffic Class to Port Priority
- 9.5 Transmit Queues Configuration Screen
  - 9.5.1 Setting the Current Queueing Mode
- 9.6 Priority Classification Configuration Screen
- 9.7 Protocol Port Configuration Screen
  - 9.7.1 Assigning Ports to a PID/Classification
  - 9.7.2 Example, Prioritizing Traffic According to Classification Rule
    - 9.7.2.1 Solving the Problem
- 9.8 Rate Limiting Configuration Screen
Layer 3 Extensions Menu Screens
- 10.1 Layer 3 Extensions Menu Screen
- 10.2 IGMP/VLAN Configuration Screen
  - 10.2.1 IGMP/VLAN Configuration Procedure
Module Statistics Menu Screens
- 11.1 Module Statistics Menu Screen
- 11.2 Switch Statistics Screen
- 11.3 Interface Statistics Screen
  - 11.3.1 Displaying Interface Statistics
- 11.4 RMON Statistics Screen
  - 11.4.1 Displaying RMON Statistics
- 11.5 Chassis Environmental Statistics Configuration Screen
Network Tools Screens
- 12.1 Network Tools
- 12.2 Built-in Commands
- 12.3 Example, Effects of Aging Time on Dynamic Egress
- 12.4 Example, Using Dynamic Egress to Control Traffic
- 12.5 Special Commands
VLAN Operation and Network Applications
- 13.1 Defining VLANs
- 13.2 Types of VLANs
  - 13.2.1 802.1Q VLANs
  - 13.2.2 Other VLAN Strategies
- 13.3 Benefits and Restrictions
- 13.4 VLAN Terms
- 13.5 VLAN Operation
  - 13.5.1 Description
  - 13.5.2 VLAN Components
- 13.6 Configuration Process
- 13.7 VLAN Switch Operation
  - 13.7.1 Receiving Frames from VLAN Ports
  - 13.7.2 Forwarding Decisions
    - 13.7.2.1 Broadcasts, Multicasts, and Unknown Unicasts
    - 13.7.2.2 Known Unicasts
- 13.8 VLAN Configuration
- 13.9 Summary of VLAN Local Management
  - 13.9.1 Preparing for VLAN Configuration
- 13.10 Quick VLAN Walkthrough
- 13.11 Examples
- 13.12 Example 1, Single Switch Operation
  - 13.12.1 Solving the Problem
  - 13.12.2 Frame Handling
- 13.13 Example 2, VLANs Across Multiple Switches
  - 13.13.1 Solving the Problem
  - 13.13.2 Frame Handling
- 13.14 Example 3, Filtering Traffic According to a Layer 4 Classification Rule
  - 13.14.1 Solving the Problem
- 13.15 Example 4, Securing Sensitive Information According to Subnet
  - 13.15.1 Solving the Problem
- 13.16 Example 5, Using Dynamic Egress to Control Traffic
- 13.17 Example 6, Locking a MAC Address to a Port Using Classification Rules
  - 13.17.1 Solving the Problem
Generic Attribute Registration Protocol (GARP)
- A.1 Operation
- A.2 How It Works
About IGMP
- B.1 IGMP Overview
- B.2 Supported Features and Functions
- B.3 Detecting Multicast Routers
Index
- Numerics
- A
- B
- C
- D
- E
- F
- G
- H
- I
- K
- L
- M
- N
- P
- Q
- R
- S
- T
- U
- V
- W

VLAN Redirect Configuration Screen

Chassis Menu Screens 4-23

14. Use the SPACE bar to select either the ADD or DELETE option. Press ENTER. This adds or

deletes the selections for the Source Port, Destination Port, Frame Format, and Redirect Errors

made in steps 1 through 12 and also updates the screen.

15. Use the arrow keys to highlight SAVE at the bottom of the screen. Press ENTER. The message

“SAVED OK” displays. This saves the new settings and updates the Source Port and Module,

and the Destination Port and Module read-only fields.

4.9 VLAN REDIRECT CONFIGURATION SCREEN

When to Use

To select a source module and VLAN ID and a destination module and port as well to add a new

VLAN Redirect or delete an existing one. For example, VLAN ID 1 can be set as the source

VLAN ID with port 2 as the destination port. Traffic from VLAN 1 is then automatically

redirected to port 2 according to the Frame Format setting for that source VLAN. The Frame

Format setting determines the format in which the frames received belonging to the source VLAN

are redirected to the destination port. The frames can be forwarded in the frame format as received,

tagged, or untagged.

The VLAN redirect function is very useful for troubleshooting purposes, as it allows traffic

associated with a particular VLAN to be sent to a particular port where, with the use of an analyzer

or RMON probe, all current traffic from the source VLAN can be examined.

TIP: If more than one port is being redirected, repeat steps 1 through 14 for each

additional setting. Then go to step 15 to save all the new settings at once.

If an entry is to be changed, delete the entry, save the screen, then recreate the entry

with its new settings.

Any combination of port redirect instances (configured on the Port Redirect

Configuration screen) and/or VLAN redirect instances (configured on the VLAN Redirect

Configuration screen) can be configured, up to 128 instances total per module. A

maximum of 640 instances can be configured on a fully loaded (5 module) chassis. Up

to 24 instances can be configured as remote instances to other modules in the chassis.

Remote instances are instances that are mapped from one module to another within the

same chassis.

NOTE: Although traffic associated with a particular VLAN is sent to the destination port,

normal switching is still performed for all frames on the source port.

The Redirect Errors function is not supported on this screen.