SecureStack C2 PoE Redundant Power Supply C2RPS-POE Installation Guide C2RPS-POE POWER Caution: Do not use this product with SecureStack C2 non-PoE devices. Any SecureStack C2 device without a “P” suffix in the model number (C2xxxx-xx) indicates a SecureStack C2 PoE non-compliant device and is not compatible with this power system. Precaución: La fuente de poder C2RPS-POE no es compatible con switches SecureStack C2 que no cumplan con el estándar PoE.
Electrical Hazard: Only qualified personnel should perform installation procedures. Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion. Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden. Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice.
Regulatory Compliance Information Federal Communications Commission (FCC) Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.
Electromagnetic Compatibility (EMC) This product complies with the following: 47 CFR Parts 2 and 15, CSA C108.8, 89/336/EEC, EN 55022, EN 61000‐3‐2, EN 61000‐3‐3, EN 55024, AS/NZS CISPR 22, VCCI V‐3. Compatibilidad Electromágnetica (EMC) Este producto de Enterasys cumple con lo siguiente: 47 CFR Partes 2 y 15, CSA C108.8, 89/336/EEC, EN 55022, EN 55024, EN 61000‐3‐2, EN 61000‐3‐3, AS/NZS CISPR 22, VCCI V‐3.
Declaration of Conformity Application of Council Directive(s): 89/336/EEC 73/23/EEC Manufacturer’s Name: Enterasys Networks, Inc. Manufacturer’s Address: 50 Minuteman Road Andover, MA 01810 USA European Representative Address: Enterasys Networks, Ltd.
Enterasys Networks, Inc. Firmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys Networks, Inc.
3. APPLICABLE LAW. This Agreement shall be interpreted and governed under the laws and in the state and federal courts of the Commonwealth of Massachusetts without regard to its conflicts of laws provisions. You accept the personal jurisdiction and venue of the Commonwealth of Massachusetts courts.
8. AUDIT RIGHTS. You hereby acknowledge that the intellectual property rights associated with the Program are of critical value to Enterasys and, accordingly, You hereby agree to maintain complete books, records and accounts showing (i) license fees due and paid, and (ii) the use, copying and deployment of the Program.
viii
Contents About this Guide Using This Guide ................................................................................................................................. xi Structure of This Guide ........................................................................................................................ xi Using the SecureStack C2 Manual Set ............................................................................................... xii Conventions Used in This Guide .....................
Tables 1-1 2-1 2-2 A-1 A-2 A-3 x Powered Device (PD) PoE Power Classifications..................................................................1-3 Contents of N-POE Chassis Carton.......................................................................................2-2 C2RPS-POE Status LED Indications and Recommended Actions........................................2-7 C2RPS-POE Specifications ..................................................................................................
About this Guide This guide provides an overview, installation and troubleshooting instructions, and specifications for the Enterasys SecureStack C2RPS‐POE power supply, which can provide a redundant power source to a SecureStack standalone POE switch. Using This Guide Read through this guide completely to familiarize yourself with its contents and gain an understanding of the features and capabilities of the C2RPS‐POE power supply.
Using the SecureStack C2 Manual Set Using the SecureStack C2 Manual Set Other manuals have been developed for the SecureStack C2 PoE switch devices that can be connected to the C2RPS‐POE power supply for power redundancy. Caution: The C2RPS-POE power supply does not support non-PoE compliant SecureStack C2 switches. Do not try to connect the power cable from this C2RPS-POE power supply to any SecureStack C2 stackable switch that does not have a “P” suffix in the model name, such as C2G124-24.
Conventions Used in This Guide Conventions Used in This Guide The following conventions are used in this guide: Note: Calls the reader’s attention to any item of information that may be of special importance. Caution: Contains information essential to avoid damage to the equipment. Precaución: Contiene información esencial para prevenir dañar el equipo. Achtung: Verweißt auf wichtige Informationen zum Schutz gegen Beschädigungen.
Conventions Used in This Guide xiv About this Guide
1 Introduction This chapter provides the following information: For information about... Refer to page...
C2RPS-POE Overview C2RPS-POE Overview The purpose of the C2RPS‐POE is to provide power backup to an Enterasys SecureStack C2 PoE‐compliant stackable switch. If for some reason the switch looses power from its internal power supply, the C2RPS‐POE can provide up to 500 Watts maximum operating power to support switch operation and the 48 Vdc cessary to support 48 Vdc/data connections to PDs (Powered Devices). The C2RPS‐POE is shown in Figure 1‐1.
Power Classifications and Deployment The number of PDs that can be supported by the connected SecureStack PoE switch can be estimated by adding up the maximum power requirement of each connected PD according to their Power Classification rating (0 through 4). Note: Use the highest power rating of PoE Power Class of each PD to calculate the maximum wattage. For example, such as 12.95 for a Class 0 device.
Getting Help The SecureStack PoE switch has six of its PoE/data ports connected to PDs with the following Class ratings: • One does not support PoE (no power) • One has no Class rating (Defaults to Class 0, 12.95 Watts maximum) • Two are Class 2 (6.49 Watts maximum x 2 = 12.98 Watts total) • One is Class 0 (12.95 Watts maximum) • One is Class 4 (defaults to 12.95 Watts maximum) The maximum power needed from the C2RPS‐POE is 51.83 Watts for the PDs, which is far below the maximum of 370 Watts.
2 Installation Electrical Hazard: Only qualified personnel should perform installation procedures. Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion. Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden. This chapter provides the installation instructions to install all the components of a C2RPS‐POE. To correctly install the C2RPS‐POE, follow the order of information listed below.
Unpacking the C2RPS-POE Unpacking the C2RPS-POE To unpack the C2RPS‐POE, proceed as follows: 1. Open the box and remove the packing material protecting the devices. 2. Verify the contents of each carton and compare the contents shipped with those listed in Table 2‐1. 3. Perform a visual inspection of the devices for any signs of physical damage. Contact Enterasys Networks if there are any signs of damage. Refer to “Getting Help” on page 1‐4 for details.
Installing the C2RPS-POE on a Flat Surface Installing the Rubber Feet To install the rubber feet, refer to Figure 2‐1 and proceed as follows: 1. Place the C2RPS‐POE on its back on a sturdy flat surface to gain access to the bottom of the chassis. 2. Remove the four rubber feet from their plastic bag in the shipping box. 3. Locate the four marked locations on the bottom four corners of the C2RPS‐POE.
Installing the C2RPS-POE on a Flat Surface Guidelines for Installation Locate the C2RPS‐POE within 152 cm (5 ft) of its power source and on a surface as shown in Figure 2‐2. Caution: To ensure proper ventilation and prevent overheating, leave a minimum clearance space of 5.1 cm (2.0 in.) at the left, right, and rear of the switch.
Rack Mounting the C2RPS-POE Rack Mounting the C2RPS-POE Caution: Observe all Electrostatic Discharge (ESD) precautions when handling sensitive electronic equipment. Precaución: Al trabajar con equipos electrónicos sensibles, tome todas las precauciones de seguridad para evitar descargas de electricidad estática. To install the switch in a 19‐inch rack, you need: • Two rackmount brackets and mounting screws (rackmount kit) shipped with the switch.
Rack Mounting the C2RPS-POE Attaching Brackets and Installing in Rack Proceed as follows to install the switch into a 19‐inch rack: 1. Attach the rackmount brackets to the switch, as shown in Figure 2‐3, using the eight M3 x 6 mm flathead screws shipped with the switch. Figure 2-3 Attaching the Rackmount Brackets C2RPS-POE POWER Á À À 1 Rackmount brackets (2) 2.
Connecting C2RPS-POE Cable and AC Power Cord Connecting C2RPS-POE Cable and AC Power Cord The C2RPS‐POE is connected to the SecureStack PoE switch using a C2RPS‐POE cable, as follows: 1. Connect one end of the C2RPS‐POE (shown in Figure 2‐5) to the Redundant Power Supply connector on the switch device. Then connect the other end to the Redundant Power Supply connector at the rear of the C2RPS‐POE as shown in Figure 2‐6 and Figure 2‐7. 2.
Connecting C2RPS-POE Cable and AC Power Cord If you need additional help, contact Enterasys Networks. Refer to “Getting Help” on page 1‐4 for instructions. Figure 2-5 C2RPS-POE Cable Figure 2-6 Power Connector on C2RPS-POE (rear view) AC 10 LIN 0-2 50 40 E 10 -60 VAC .0 Hz A MA X Re DCdund +1 Lin ant 2V e -50Po we /10 V r Su .5A /7. pp MA 5A ly X MA X, SE RIA L NO . Á À 1 AC power plug 2 AC power connector 2-8 Installation  10AC L 0- IN 5 240 E 10 0-60 VAC .
Connecting C2RPS-POE Cable and AC Power Cord Figure 2-7 C2RPS-POE Cable and AC Power Cord Connections Redundant Power Supply STACK UP AC LINE 100-240 VAC 50-60 Hz 0.8 A MAX STACK DOWN MAC ADDRESS SERIAL NO. Ã À Å Ä Á Â AC LINE 100-240 VAC 50-60 Hz 10.0 A MAX Redundant Power Supply DC Line -50V /7.5A MAX, +12V /10.5A MAX SERIAL NO.
Connecting C2RPS-POE Cable and AC Power Cord 2-10 Installation
A Specifications This appendix provides information about the following: For information about... Refer to page... C2RPS-POE Specifications A-1 C2RPS-POE Redundant Power Supply Output Connector A-2 Compliance Standards A-3 Enterasys Networks reserves the right to change the specifications at any time without notice.
C2RPS-POE Redundant Power Supply Output Connector Table A-1 C2RPS-POE Specifications (continued) Item Specification Physical Dimensions 4.45 H x 44.5 W x 16.5 D (cm) 1.75 H x 17.5 W x 6.5 D (in.) Net Weight (unit only) 3.47 kg (7.63 lb) Gross Weight (1 unit and packaging) 4.95 kg (10.
Compliance Standards Table A-2 C2RPS-POE Redundant Power Supply Connector Pin Functions Pin Number Function 1 - 50 V return 2 - 50 Vdc 3 12 Vdc output 4 12 Vdc output 5 12 Vdc output 6 12 Vdc output 7 Ground 8 Ground 9 No connection 10 RPS present 11 Status 1 12 Status 2 13 Power good 14 Ground Compliance Standards The C2RPS‐POE meets the safety and electromagnetic compatibility (EMC) requirements listed in Table A‐3: Table A-3 Compliance Standards Item Standard Safety
Compliance Standards A-4 Specifications
