RoamAbout ™ Wireless Networking Access Point 3000 Hardware Installation Guide P/N 9033978-01
Electrical Hazard: Only qualified personnel should perform installation procedures. Riesgo Eléctrico: Solamente personal calificado debe realizar procedimientos de instalacion. Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden. Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its Web site without prior notice.
Radio Certification and Regulatory Information Zertifizierung für Funkgeräte und gesetzliche Vorschriften Caution: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Precaución: Cualquier cambio o modificación a este dispositivo sin la aprobación del organismo autorizado, puede anular el derecho del usuario a operar el equipo.
Ein Artikel, der mit CExxxx oder dem CE‐Warnhinweis gekennzeichnet ist, enthält einen Funksender, der den Anforderungen der R&TTE‐Richtlinie (1999/5/EC) der EU‐Kommission entspricht. Die Übereinstimmung mit dieser Richtlinie schließt die Konformität mit den folgenden europäischen Normen ein (die entsprechenden internationalen Normen sind in Klammern angegeben). • EN 300 328‐1 December 2001 V1.3.1 • EN 300 328‐2 December 2001 V1.2.1 • EN 301 893 August 2003 V1.2.3 • EN 301 489‐1 August 2002 V1.2.
VCCI Notice This is a Class B product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Channel Information 802.11a • Europe: 19 non‐overlapping channel (5.15 ~ 5.35 GHz, 5.47 ~ 5.725 GHz) • Japan: 4 non‐overlapping channels (5.15 ~ 5.
Enterasys erklärt hiermit, dass dieses LAN‐Funkgerät die wesentlichen Anforderungen und sonstigen relevanten Vorschriften der R&TTE‐Richtlinie 1999/5/EC erfüllt. Eine Kopie dieser unterzeichneten Erklärung erhalten Sie von Enterasys Networks, 50 Minuteman Road, Andover, MA 01810, USA. Attn: Wireless Group. Approved Countries The following table lists the approved countries, Access Point 3000 part numbers, and if applicable, the approval numbers and references.
Country Finland (FIN) Part Number RBT3K-AG IEEE 802.11a Only IEEE 802.11 b/g Only 5150 – 5350 MHz < 200 mW EIRP (Indoors only) 2400 – 2483.5 MHz < 100 mW EIRP (Indoors only) Comments 5470 – 5725 MHz < 1 W EIRP (Indoors only) France (F) Germany (D) RBT3K-AG RBT3K-AG 5150 – 5350-MHz < 200 mW EIRP (Indoors only) 1>2400 -2483.5 MHz < 100 mW eirp (Indoors only) 5470 – 5725 MHz Under examination (Not permitted) 2>2400 – 2483.
Country Part Number IEEE 802.11a Only IEEE 802.11 b/g Only Comments Italy (I) RBT3K-AG 5150 – 5350 MHz < 200 mW EIRP (Indoors only) 1>2400 – 2483.5 MHz < 100 mW EIRP (Indoors only) 1> If used outside of own premises, general authorization is required. 1>2400 – 2483.5 MHz < 100 mW EIRP (Indoors only) 1> If used outside of own premises, general authorization is required.
Country Portugal (P) Part Number RBT3K-AG IEEE 802.11a Only IEEE 802.11 b/g Only 5150 – 5350 MHz < 200 mW EIRP (Indoors only) 2400 – 2483.5 MHz < 100 mW EIRP (Indoors only) Comments 5470 – 5725 MHz < 1 W EIRP (Indoors only) Slovenia (SA) RBT3K-AG 5150 – 5350 MHz < 200 mW EIRP (Indoors only) 2400 – 2483.5 MHz < 100 mW EIRP (Indoors only) 5470 – 5725 MHz < 1 W EIRP (Indoors only) Slovakia (SK) RBT3K-AG 5150 – 5350-MHz < 120 mW EIRP (Indoors only) 2400 – 2483.
Enterasys Networks, Inc. Firmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys Networks, Inc.
4. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the Program is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party.
10. ENFORCEMENT. You acknowledge and agree that any breach of Sections 2, 4, or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate, and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys’ rights under this Agreement in addition to any and all remedies available at law. 11. ASSIGNMENT.
xii
Contents About This Guide Purpose of This Manual ....................................................................................................................................xv Intended Audience ............................................................................................................................................xv Associated Documents .....................................................................................................................................
Network Management ..............................................................................................................................A-3 Temperature .............................................................................................................................................A-3 Humidity ...................................................................................................................................................A-3 EMC Compliance (Class B) .....................
About This Guide Purpose of This Manual This manual describes how to install the RoamAbout Access Point 3000. It also includes basic configuration information, problem solving, and connector pin assignment information. Intended Audience This manual is intended for use by personnel who will install and set up the RoamAbout Access Point 3000. Electrical Hazard: Only qualified personnel should perform installation procedures.
Getting Help For additional support related to this device or document, contact Enterasys Networks using one of the following methods. World Wide Web: www.enterasys.com/support Phone: (603) 332-9400 1-800-872-8440 (toll-free in the U.S. and Canada) For the Enterasys Networks Support toll-free number in your country: www.enterasys.com/support/gtac-all.html Email: support@enterasys.com To expedite your message, please type [wireless] in the subject line.
1 Introduction Overview The Enterasys Networks Wireless Access Point 3000 is an IEEE 802.11a/b/g (RBT3K‐AG & RBT3K‐AG‐G), or an IEEE 802.11b/g only (RBT3K‐1G), access point that provides transparent, wireless high‐speed data communications between the wired LAN and fixed, portable or mobile devices equipped with an 802.11a, 802.11b or 802.11g wireless adapter.
Hardware Description Hardware Description Figure 1‐1 displays the top view and back panel of the Access Point 3000. Figure 1-1 Access Point 3000 1 A B/G 2 LOCK CONSOLE 5 1 Status indicators for Access Point and the 802.11a and 802.
Component Description Component Description Antennas The access point includes two antennas for wireless communications. The signal transmitted from both antennas is identical, but only the best signal received on one of the antennas is used. The antennas transmit the outgoing signal along a horizontal plane perpendicular to the antenna (in the shape of a toroidal sphere, or a donut). The antennas should be adjusted to different angles to provide better coverage.
Component Description Table 1-1 LED Indicator Descriptions (continued) LED B/G 802.11g or 802.11b Radio Interface 2 Status Description On Indicates a valid 802.11g or 802.11b wireless link. Very Slow Flashing Searching for network association. Slow Flashing Associated with network but no activity. Fast Flashing Indicates that the access point is transmitting or receiving data through wireless links. Flashing rate is proportional to network activity.
Features and Benefits Power Connector The access point does not have a power switch. It is powered on when connected to the AC power adapter, and the power adapter is connected to a power source. The power supply automatically adjusts to any voltage between 100‐240 volts at 50 or 60 Hz. No voltage range settings are required. The access point may also receive Power over Ethernet (PoE) from a switch or other network device that supplies power over the network cable based on the IEEE 802.3af standard.
Applications 1-6 Introduction
2 Hardware Installation Preparing to Install Choose a proper place for the access point. The best location is at the center of your wireless coverage area, within line of sight of all wireless devices. Try to place the access point in a position that can best cover its Basic Service Set (refer to RoamAbout Access Point 3000 Configuration Guide). Normally, the higher you place the access point, the better the performance. Electrical Hazard: Only qualified personnel should perform installation procedures.
Mounting the Access Point Mounting on a Wall To mount the Access Point 3000 on a wall, perform the following steps: 2-2 1. Locate at least two mounting holes/slots on the mounting bracket that line up with a wall stud. 2. Use two screws to secure the flat side of the mounting bracket to the wall stud. Use plastic anchors, or self‐anchoring screws (not included) to secure the mounting bracket to the wallboard, as shown below. 3.
Mounting the Access Point 4. Slide the access point over the raised tabs and lock them into place, as shown in the following figure. Note: The access point will not slide if it was successfully locked into place.
Mounting the Access Point Mounting on the Ceiling To mount the Access Point 3000 on the ceiling, perform the following steps: 2-4 1. If you received washers with your kit, discard them. 2. Attach the mounting clips to the mounting bracket as shown below. Ensure that the screws line up with the holes on the tab of each side of the mounting bracket. Ensure that the nuts are secure, but do not tighten them. 3. Slide the mounting clips over the ceiling support, as shown below. 4.
Removing the Access Point from the Mounting Bracket 5. Slide the access point over the mounting bracket to locate the three raised tabs. and lock them in place, as shown below. Note: The access point will not slide if it was successfully locked into place. 6. Attach the locking clip to the mounting bracket and to the access point, as shown below. /3A DC 5V POE IN E CONS OL LOCK Removing the Access Point from the Mounting Bracket To remove the access point from the mounting bracket: 1.
Connecting the Cables Connecting the Cables Note: Refer to Appendix C for cabling and pin-out information. Perform the following steps to connect the cables and power on the access point: Connect the Ethernet Cable. The access point can be wired to a 10/100 Mbps Ethernet through a network device, such as a hub or a switch. Connect your network to the RJ‐45 port on the back panel with category 3, 4, or 5 UTP Ethernet cable.
Connecting the Cables 2. Connect the Power Cord. Connect the power adapter to the access point, and the power cord to an AC power outlet. Otherwise, the access point can derive its operating power directly from the RJ‐45 port when connected to a device that provides IEEE 802.3af compliant Power over Ethernet (PoE). Caution: Use ONLY the power adapter supplied with this access point. Otherwise, the product may be damaged.
Connecting the Cables 2-8 Hardware Installation
3 Initial Configuration Overview The Enterasys Networks RoamAbout Access Point 3000 includes a Web‐based interface, and a direct connection to the console port for CLI management. You can also manage the Access Point 3000 using an SNMP manager, such as Enterasys Networks NetSight Atlas. You can perform the initial configuration steps through the CLI or the Web interface. The access point requests an IP address from a Dynamic Host Configuration Protocol (DHCP) server by default.
Using the CLI Note: When using HyperTerminal with Microsoft® Windows® 2000, make sure that you have Windows 2000 Service Pack 2 or later installed. Windows 2000 Service Pack 2 fixes the problem of arrow keys not functioning in HyperTerminal’s VT100 emulation. See www.microsoft.com for information on Windows 2000 service packs. 4. Once you have set up the terminal correctly, press the Enter key to initiate the console connection. The console login screen will be displayed.
Using the CLI b. Determine the code for your country, and then type country followed by your country code (for example, country US for United States). c. Reboot the RoamAbout Access Point 3000. RoamAbout 3000#country US Please reset the AP to make the country code change effective RoamAbout 3000#reset board Reboot system now? : y Username: admin Password:******** RoamAbout 3000# 5. If your access point uses a DHCP assigned IP address go on to change the default username and password.
Using the CLI 6. Change the default username and password: type username and specify a unique user name; type password and specify a unique password. RoamAbout 3000(config)#username JadaPerl RoamAbout 3000(config)#password G7nq1Z Confirm new password: G7nq1Z RoamAbout 3000(config)# 7. Enable Management VLAN. Note: Before enabling the VLAN feature on the access point, you must set up the network switch port to support tagged VLAN packets from the access point.
Using Web Management Using Web Management To use the Web interface to minimally configure the access point, perform the following steps: 1. Open a Web browser and enter the access point’s IP address in the address field: – If your access point uses a DHCP assigned IP address, make sure the access point is connected to your network and enter the DHCP assigned IP address in your browser’s address field (use your DHCP server or other utility to determine the access point’s IP address).
Using Web Management 3. To set the Country, perform the following steps: a. Click the arrow in the Country pull‐down menu to select the appropriate country, then click Apply at the bottom of the page. The access point prompts you to reset. b. Click OK. The Identification page appears. 4. 3-6 Initial Configuration Click Administration from the menu on the left‐hand side of the page.
Using Web Management The Administration page appears. a. Click Reset, at the bottom of the page. The access point prompts you to confirm that you want to reboot the system. b. Click OK. The access point reboots and the Login window appears. 5. Enter the username admin and the password password, and click LOGIN. 6. To set a static IP address, perform the following steps: a. Click TCP/IP Settings from the menu on the left of the page. The TCP/IP Settings page appears.
Using Web Management b. Click the DHCP Client: Disable radio button. An IP Address section appears on the page. c. Specify IP address, Subnet Mask, Default Gateway, and Primary and Secondary DNS. d. Click Apply at the bottom of the page. e. Type the IP address that you specified for the access point in your browser’s address field. For example, enter http://10.2.101.22/. The Login window appears. f. Enter the username admin and the password password, and click LOGIN. g.
Using Web Management c. Specify a new password in the Password field. d. Specify the new password again in the Confirm Password field. e. Click Apply at the bottom of the page. The access point displays a Settings Saved message. f. Click OK. The Administration page appears. 8. Set management VLAN: a. Click Filter Control from the menu on the left of the page. The Filter Control page appears. b. Click the Management VLAN ID: field, and enter the VLAN ID from which you will manage the AP. c.
Using Web Management d. Click Apply at the bottom of the page. The access point displays a dialog box indicating that the VLAN status has changed and will take effect after the next reboot. The dialog box prompts you to choose whether to reboot now or later. e. Click OK to reboot now. The access point reboots and the Login window appears. f. 9. 3-10 Enter the username and the password that you specified for this access point, and click LOGIN.
A Specifications General Specifications Maximum Channels 802.11a: US & Canada: 13 (normal mode), 5 (turbo mode) Japan: 4 (normal mode), 1 (turbo mode) ETSI: 11 channels (normal mode), 4 (turbo mode) 802.11b/g: FCC/IC: 1 to 11 ETSI: 1 to 13 France: 10 to 13 MKK: 1 to 14 Maximum Clients 250 if you are NOT using encryption or authentication. 120 if you ARE using encryption or authentication. Operating Range See “Maximum Distance Tables” on page D‐3. Data Rate 802.
General Specifications Modulation Type 802.11a: BPSK, QPSK, 16‐QAM, 64‐QAM 802.11g: CCK, BPSK, QPSK, OFDM 802.11b: CCK, BPSK, QPSK Network Configuration Infrastructure Operating Frequency 802.11a: 5.15 to 5.25 GHz (lower band) US/Canada, Japan 5.25 to 5.35 GHz (middle band) US/Canada 5.725 to 5.825 GHz (upper band) US/Canada 5.50 to 5.70 GHz Europe 802.11b/g: 2.4 to 2.4835 GHz (US, Canada, ETSI) 2.4 to 2.497 GHz (Japan) Power Supply Input: 100 to 240 AC, 50 to 60 Hz Output: 5.
General Specifications Network Management Web‐browser, RS232 console, Telnet, SNMP Temperature Operating: 0°C to 55°C (32°F to 131 °F) Storage: 0°C to 70 °C (32 °F to 158 °F) Humidity 15% to 95% (non‐condensing) EMC Compliance (Class B) FCC Class B (US) ICES‐003 (Canada) VCCI (Japan) RCR STD‐33A EN55024, EN5022 Radio Signal Certification For the latest radio certification and regulatory information, go to http://www.enterasys.com/products/wireless/. The information is listed under County Approvals.
General Specifications Safety CSA/NTRL (CSA 22.2 No. 950 & UL 1950) EN60950 (TÜV/GS), IEC60950 (CB) LVD/EN 60950 Plenum Rated UL2043 Standards IEEE 802.3 10BASE‐T, IEEE 802.3u 100BASE‐TX, IEEE 802.11a, 802.11b, 802.
Sensitivity Sensitivity 802.11a IEEE 802.11a Sensitivity (GHz - dBm) Modulation/Rates 5.15-5.250 5.25-5.350 5.50-5.700 5.725-5.825 BPSK (6 Mbps) -88 -88 -88 -88 BPSK (9 Mbps) -87 -87 -87 -87 QPSK (12 Mbps) -86 -86 -86 -86 QPSK (18 Mbps) -84 -84 -84 -84 16 QAM (24 Mbps) -81 -81 -81 -81 16 QAM (36 Mbps) -77 -77 -78 -78 64 QAM (48 Mbps) -73 -73 -73 -73 64 QAM (54 Mbps) -69 -70 -70 -67 802.11g IEEE 802.
Transmit Power Transmit Power 802.11a IEEE 802.11a Maximum Output Power (GHz - dBm) Data Rate 5.15 to 5.250 5.25 to 5.350 5.50 to 5.700 5.725 to 5.825 6 Mbps 17 17 17 17 9 Mbps 17 17 17 17 12 Mbps 17 17 17 17 8 Mbps 17 17 17 17 24 Mbps 17 17 17 17 36 Mbps 17 17 17 17 48 Mbps 17 17 17 17 54 Mbps 12 17 17 16 802.11g IEEE 802.11g Maximum Output Power (GHz - dBm) Data Rate 2.412 2.417 to 2.467 2.
B Default Settings This Appendix lists the access point system defaults. To reset the access point defaults, refer to the CLI command “reset configuration” from the Exec level prompt. Refer to the RoamAbout Access Point 3000 Configuration Guide. Feature Parameter Default Identification System Name RoamAbout AP Administration User Name admin Password password DHCP Enabled HTTP Server Enabled HTTP Port 80 HTTPS Server Enabled HTTPS Port 443 IP Address 192.168.1.1 Subnet Mask 255.255.
Feature Parameter Default MAC Authentication MAC Authentication Local MAC Local MAC System Default Allow Local MAC Permission Allow Status Disabled Broadcast Key Refresh 0 minutes (disabled) Session Key Refresh 0 minutes (disabled) RADIUS Session Timeout 60 minutes 802.
Feature Parameter Default Wireless Interface 802.11a Radio Settings Enabled Native VLAN ID 1 Description RoamAbout AP3000 - 802.
Feature Parameter Default Wireless Interface 802.11b/g Radio Settings Enabled Description RoamAbout AP3000 - 802.
C Cables and Pin-outs Twisted-Pair Cable Assignments Caution: DO NOT plug a phone jack connector into the RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards. Precaución: NO utilice un conector de teléfono en el puerto RJ-45. Utilice solamente cable de par trenzado con conectores RJ-45 para cumplir con los estándares de la FCC. Achtung: Verbinden Sie keine Telefonkabel mit dem RJ-45-Anschluss.
Twisted-Pair Cable Assignments 10/100BASE-TX Pin Assignments Use unshielded twisted‐pair (UTP) or shielded twisted‐pair (STP) cable for RJ‐45 connections: 100‐ ohm Category 3 or better cable for 10 Mbps connections, or 100‐ohm Category 5 or better cable for 100 Mbps connections. Also be sure that the length of any twisted‐pair connection does not exceed 100 meters (328 feet). The RJ‐45 port on the access point is wired with MDI pinouts.
Console Port Pin Assignments Crossover Wiring Because the 10/100 Mbps port on the access point uses an MDI pin configuration, you must use “crossover” cable for network connections to PCs, servers or other end nodes that only have MDI ports. However, if the device to which you are connecting supports auto‐MDIX operation, you can use either “straight‐through” or “crossover” cable.
Console Port Pin Assignments Table C-1 Wiring Map for Serial Cable (continued) Signal (serial port) Pin Signal (management console port) RTS (request to send) 8 CTS (clear to send) Unused 9 Unused Note: The left hand column pin assignments are for the female DB-9 connector on the access point. Pin 2 (TXD or “transmit data”) must emerge on the management console’s end of the connection as RXD (“receive data”).
D Troubleshooting Troubleshooting Steps Check the following items before contacting technical support. 1. If wireless clients cannot access the network, check the following: a. Be sure the access point and the wireless clients are configured with the same Service Set ID (SSID). b. If authentication or encryption are enabled, ensure that the wireless clients are properly configured with the appropriate authentication or encryption keys. c.
Troubleshooting Steps 3. 4. If you cannot access the on‐board configuration program via a serial port connection: a. Be sure you have set the terminal emulator program to VT100 compatible, 8 data bits, 1 stop bit, no parity and 9600 bps. b. Check that the null‐modem serial cable conforms to the pin‐out connections provided in Appendix C.
Maximum Distance Tables Maximum Distance Tables Table D-4 through Table D‐6 list the wireless distances. Note: Maximum distances posted below are actual tested distance thresholds. However, there are many variables such as barrier composition and construction and local environmental interference that may impact your actual distances and cause you to experience distance thresholds far lower than those posted in the following tables. Table D-4 802.
Maximum Distance Tables D-4 Troubleshooting
