- Enterasys Gigabit and Fast Ethernet Switches Hardware Installation Guide
Table Of Contents
- Enterasys® SecureStack™ B2 Gigabit and Fast Ethernet Switches Hardware Installation Guide
- Notice
- Regulatory Compliance Information
- Federal Communications Commission (FCC) Notice
- Clase A. Aviso de ITE
- Klasse A ITE Anmerkung
- Seguridad del Producto
- Produktsicherheit
- Electromagnetic Compatibility (EMC)
- Compatibilidad Electromágnetica (EMC)
- Elektro- magnetische Kompatibilität ( EMC )
- VCCI Notice
- BSMI EMC Statement - Taiwan
- Safety Information Class 1 Laser Transceivers
- Enterasys Networks, Inc. Firmware License Agreement
- Regulatory Compliance Information
- Notice
- Contents
- About This Guide
- Introduction
- Network Requirements
- Hardware Installation
- Considerations Prior to Installation
- Required Tools
- Unpacking the Switch
- Installing Optional Mini-GBICs
- Installing the Switch on a Flat Surface
- Rack Mounting the Switch
- Connecting High-Speed Stacking Cables
- Configuring Switches in a Stack
- Connecting AC and RPS-SYS Power
- Connecting to Console Port for Local Management
- Connecting to the Network
- Completing the Installation
- Troubleshooting
- Specifications
- Index

v
VCCI NOTICE
ThisisaclassAproductbasedonthestandardoftheVoluntaryControlCouncilforInterferencebyInformation
TechnologyEquipment(VCCI).Ifthisequipmentisusedinadomesticenvironment,radiodisturbancemayarise.
Whensuchtroubleoccurs,theusermayberequiredtotakecorrectiveactions.
BSMI EMC STATEMENT — TAIWAN
ThisisaclassAproduct.Inadomesticenvironmentthisproductmaycauseradiointerferenceinwhichcasetheuser
mayberequiredtotakeadequatemeasures.
SAFETY INFORMATION
CLASS 1 LASER TRANSCEIVERS
SINGLE MODE NETWORK EXPANSION MODULES USE CLASS 1 LASER TRANSCEIVERS.
READ THE FOLLOWING SAFETY INFORMATION
BEFORE INSTALLING OR OPERATING THESE MODULES.
TheClass1lasertransceiversuseanopticalfeedbacklooptomaintainClass1operationlimits.Thiscontrolloop
eliminatestheneedformaintenancechecksoradjustments.Theoutputisfactoryset,anddoesnotallowanyuser
adjustment.Class1Lasertransceiverscomplywiththefollowingsafetystandards:
•21CFR
1040.10and1040.11U.S.DepartmentofHealthandHumanServices(FDA).
•IECPublication825(InternationalElectrotechnicalCommission).
• CENELECEN60825(EuropeanCommitteeforElectrotechnicalStandardization).
Whenoperatingwithintheirperformancelimitations,lasertransceiveroutputmeetstheClass1accessibleemission
limitofallthreestandards.Class1levelsoflaserradiationare
notconsideredhazardous.
Whentheconnectorisinplace,alllaserradiationremainswithinthefiber.Themaximumamountofradiantpower
exitingthefiber(undernormalconditions)is‐12.6dBmor55x10
‐6
watts.
Removingtheopticalconnectorfromthetransceiverallowslaserradiationtoemitdirectlyfromtheopticalport.The
maximumradiancefromtheopticalport(underworstcaseconditions)is0.8Wcm
‐2
or8x10
3
Wm
2
sr‐1.
Donotuseopticalinstrumentstoviewthelaseroutput.Theuseofopticalinstrumentstoviewlaseroutputincreases
eyehazard.Whenviewingtheoutputopticalport,powermustberemovedfromthenetworkadapter.