Mid-Span Power Hub 24-Port User’s Guide P/N 9033926
Electrical Hazard: Only qualified personnel should perform installation procedures. NOTICE Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made. The hardware, firmware, or software described in this document is subject to change without notice.
INDUSTRY CANADA NOTICE This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
ENTERASYS NETWORKS, INC. FIRMWARE LICENSE AGREEMENT BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys Networks, Inc.
3. APPLICABLE LAW. This Agreement shall be interpreted and governed under the laws and in the state and federal courts of the Commonwealth of Massachusetts without regard to its conflicts of laws provisions. You accept the personal jurisdiction and venue of the Commonwealth of Massachusetts courts.
8. AUDIT RIGHTS. You hereby acknowledge that the intellectual property rights associated with the Program are of critical value to Enterasys and, accordingly, You hereby agree to maintain complete books, records and accounts showing (i) license fees due and paid, and (ii) the use, copying and deployment of the Program.
DECLARATION OF CONFORMITY Application of Council Directive(s): Manufacturer’s Name: Manufacturer’s Address: European Representative Address: Conformance to Directive(s)/Product Standards: Equipment Type/Environment: 89/336/EEC 73/23/EEC Enterasys Networks, Inc. 50 Minuteman Road Andover, MA 01810 USA Enterasys Networks Ltd.
Contents About This Guide Purpose ................................................................................................................................................ ix Who Should Use This guide ................................................................................................................ ix Document Conventions ........................................................................................................................ ix Getting Help ..............................
viii
About This Guide Purpose This guide provides information and procedures on hardware installation, setup, configuration, and management of the Enterasys Networks 24-Port Mid-Span Power Hub (BL-69524ENT). Who Should Use This guide Electrical Hazard: Only qualified personnel should perform the installation procedures described in this guide. This guide is intended for administrative and technical personnel responsible for installing and managing Enterasys Networks products.
Getting Help For additional support related to the Mid-Span Power Hub or this document, contact Enterasys Networks using one of the following methods: World Wide Web http://www.enterasys.com Phone 603-332-9400 1-800-872-8440 (toll-free in U.S. and Canada) For the Enterasys Networks Support toll-free number in your country: http://www.enterasys.com/support/gtac-all.html Internet mail support@enterasys.
1 Introduction Functions and Features The BL-69524ENT, Enterasys Networks’ 24-port Mid-Span Power Hub, supports applications in which AC power is difficult to access, such as VoIP phones, wireless LAN access points, or IP network cameras. The Enterasys 24-port Mid-Span Power Hub acts as a “patch panel” and adds ~48 VDC to unused (non-data) wires in standard Category 5, 5e, or 6 Ethernet cable. The power unit delivers both data and power over a single standard Ethernet cable.
2 Installation and Connection Electrical Hazard: Only qualified personnel should install or service this unit.
Kit Contents Kit Contents Figure 2-1 Contents of the BL-69524ENT Kit BL-69524ENT 24-Port Mid-Span Power Hub Use Guidr’s e 2-2 Installation and Connection Power Cord
Technical Considerations Technical Considerations The Enterasys Networks 24-port Mid-Span Power Hub may be placed on a shelf or mounted in a standard 48.26-centimeter (19-inch) rack. Before you mount the unit to a fixed location, consider the following: • Determine optimal placement. • Collect and document network information as required. • Ensure that the length of cable from the Ethernet network source to the powered device does not exceed 100 meters.
Configuration for the 24-Port Mid-Span Power Hub Configuration for the 24-Port Mid-Span Power Hub Figure 2-2 shows a typical configuration for the Enterasys 24-port Mid-Span Power Hub operating with 802.3af appliances. To ensure EMC compliance and compliance with Class A requirements, use Category 5, 5e, or 6 shielded twisted pair straight-through cables.
Powering Up Powering Up Simply plug one end of the power cord into the unit, and the other end into a grounded AC power source. Units are typically connected to a power strip or other power outlet that may be cycled on and off. An uninterruptible power supply may also be used. Check to make sure each module installed displays a green Power LED (see Figure 2-3). Verify that any module that does not display a green Power LED is properly seated in the chassis backplane.
3 Troubleshooting Refer to Table 3-1 for a checklist of problems and recommended actions to resolve the problem. If additional support is needed, refer to “Getting Help” on page x. Table 3-1 Troubleshooting Checklist Problem Recommended Action Unit is plugged into the Enterasys Mid-Span Power Hub, but main power LED is “off.” Verify the use of a good AC cable with a good ground connection. Verify that the AC is “hot” and that voltage is between 100 VAC to 264 VAC (50 Hz to 60 Hz).
Troubleshooting Table 3-1 Troubleshooting Checklist (continued) Problem Recommended Action The Mid-Span Power Hub operates and the load device works, but there is no data link. Verify that the Detect/Power Forwarding (blue) LED for the port is “on.” Verify that the Mid-Span Power Hub is connected to the Ethernet network with a good connection. Verify that the Ethernet cable is Category 5, 5e, or 6 and is less than 100 meters in length from the Ethernet source to the load.
A Hardware Specifications Certifications The equipment meets the following safety standards and emissions requirements: Safety UL 1950 and cUL Emissions FCC Class A EN 55022, Class A EN 55024, CE Mark (CISPR 22 Class A) CB certified per IEC 60950 Standards P802.
Model BL-69524ENT Physical/Mechanical Specifications Table A-1 provides physical and mechanical specifications for the 24-port Mid-Span Power Hub. Table A-1 Physical and Mechanical Specifications Item Specification Chassis Type 48.26 cm (19 in.) rackmount with 3 modules Chassis Size 44.45 cm W x 41.28 cm D x 4.45 cm H (17.5 in. W x 16.25 in. D x 1.75 in. H) Module Type Removable, hot swappable Weight 9 kg (20 lbs) LED Indicators/Module Table A-2 provides module LED states and their definitions.
Model BL-69524ENT Electrical Specifications AC Power Input Voltage 90–264 V autoranging (46 Hz–63 Hz) Connector 3-pin with ground Chassis grounding yes Power supply single DC Port Power Output Power enabling IEEE 802.3af Power pins Unused pairs, pins 4,5(+), 7,8(-) Maximum power/port 15.6 W Maximum power, all ports active 24 ports at 15.6 W each Module-to-module isolation 1500 V RMS Overload protection If current reaches 400–450 mA for 300–400 milliseconds, then the port shuts down.
