Specifications

Troubleshooting
Troubleshooting
About the CancekNo Button
Pressing (CANCEL-NO] will usually abort the command in response to any of the following error
messages unless otherwise noted.
When using DAT BACKUP/RESTORE, be certain you want to completely abort your DAT
BACKUP, RESTORE or VERIFY before pressing (CANCEL-NO).
Error/Informational Messages (in alphabetical order)
l-
Message displayed:
RUDIU DEU NUT SELECTED
COPINR,ND RBURTE3
tONFIGURE RTRKS FIRST
DR: CHECKSUN ERROR
DRT FROII JJRONG SET
DRT VERIFY ERROR
DRTR NCT FUL’ND
DIFFERENT SIZE DRIVES
DlSK DRIPE NUT RERDY
DISK HRS BEEN CHRNGED
Defined/What to Do:
If you configure for ATRK PLAY/REC=SCSI with REC SCSI DRIVE set to one
SCSI Device ID number, and then you run CHANGE STORAGE DEVICE and
set the current storage device to a different SCSI Device ID number.
This will also appear if you try to play DiskTracks from a device that is not
currently selected (regardless of what the REC SCSI DRIVE is set to).
Pressing (CANCELSNO) in response to any prompt or parameter page (unless
specified otherwise) will abort the command, and momentarily display this.
If you are configured for SCSI, with SCSI REC DRIVE=NONE, and you try to
enter record with an Audio Track selected.
During RESTORE or VERIFY, the ASR-10 has read the wrong backup packet
checksum from the DAT tape.
You will have the option to RETRY here. (See User Retry section.)
A tape from the wrong backup set has been inserted. You will be given the
chance to insert the correct tape after pressing (ENTER-YES) .
You will have the option to RETRY here. (See User Retry section.)
The backup packet on the DAT tape does not verify with the data on the
selected SCSI Storage Device.
You will have the option to RETRY here. (See User Retry section.)
During RESTORE or VERIFY, the ASR-10 has not read the backup data
packet number it is expecting from the DAT tape, or the data is unreadable.
You will have the option to RETRY here. (See User Retry section.)
The backed-up data on the DAT tape is not from the same size drive as the
selected SCSI Storage Device.
Select a SCSI Storage Device that is either the same drive as the one used for
BACKUP or another that is the same size.
This message usually occurs when the ASR-10 is trying to access the floppy
drive or a removable SCSI storage device when there is no disk or cartridge
in
the drive, or when the SCSI storage device is spinning up.
If this message occurs, insert a floppy disk or cartridge in the drive, then use
the CHANGE STORAGE DEVICE command to select the appropriate SCSI
Device ID number (or press (LOAD) , then (INSTRUMENT)). Make sure the disk
or cartridge has been inserted into the disk drive or SCSI Storage Device and
has had a chance to spin up. This event may take place because of improperly
saved files. Refer to the section on “Transferring Banks from a Floppy Disk to
a SCSI Storage Device.”
The disk (or cartridge) has been ejected from the drive since the last time the
drive was accessed by the ASR-10. This is also displayed when the ASR-10
can’t find the Temporary Record Files when you entered record on an Audio
Track while configured for ATRK PLAY/REC=SCSI, or the available recording
space within the Temporary Record File has been depleted.
Reinsert the disk or cartridge, press (LOAD), then (INSTRUMENT), and
continue.
This is also displayed if the Akai or Roland format SCSI Stora e Device is
changed after the directory is read, and you press (ENTER-YES to begin
importing an Akai program or Roland patch. The command will be aborted.
ENSONIQ A.%-10 Version 3 Operating System
87