WoBoard / WoBoard S WoBoard / WoBoard S USER GUIDE www.enskate.com support@enskate.
CONTENTS 2 ................................. Security Warnings 2 ................................. Introduction Of WoBoard /WoBoard S 5 ................................. Introduction Of Battery 6 ................................. Introduction Of Remote Control 7 ................................. Prepare For Riding 10 ................................. Operating Limits 11 ................................. Troubleshooting 12 ................................. Other Safety Warnings 14 ...........................
Instruction Manual for WoBoard / WoBoard S I. Security warnings You should read, understand and abide by the terms and conditions of the user guide before riding skateboard. Riders may risk death or serious injury from loss of control and falls. Always wear helmet and protective gear such as knee pads, elbow pads, wrist pads while riding skateboard. DO NOT ride the board if you are under the age of 16 years old. Avoid riding on uneven surfaces, dirt, sand, steep hills, cracks, rocks might cause a fall.
2-2 Schematic diagram and description of skateboard A B C D E F G H I J K L （Figure 2） Serial number Name A Display screen (View figure 3) C Driven wheel (Front wheel) B D E F G H I J K L Front indicator light Maple wood Battery Carbon Fiber Sticker Sandpaper Control Panel Power switch Charging port Motor Tail lights - 03 -
A. Description of identifiers on the display screen: （Figure 3） Front light indicator. Turn on the front light of the skateboard, and the identifier appears; Rear warning light indicator. Turn on the rear warning light of the skateboard, and the identifier appears; Displays real-time riding speed; Bluetooth light of skateboard; Remote control pairing identifier; Riding mileage. Record riding mileage; Current battery status of the skateboard; Temperature of the main control panel of the skateboard.
III. Introduction of battery 3-1 Schematic diagram and description of battery Internal battery inside the battery case as Figure 2-E. Please keep it clean and dry. 3-2 Power specifications and parameters: Enclosure material Flame retardant grade engineering plastics Battery cell SamSung 18650 Voltage DC 36V Capacity USB output Wobaord 2.5Ah / Wobaord S 3.5Ah 42V 2A 3-3 Description of battery recharging: Charging Method: Connect the standard charger AC with 100-240VAC socket.
IV. Introduction of remote control 4-1 Schematic diagram and description of remote control A B C D E Advanced speed mode Advanced eco mode Intermediate mode Beginner mode F G (Figure 5-1) (Figure 5-2) A.Remote control switch: 1 .Short press to turn on remote, hold for 3 seconds to turn off. 2. Speed mode switch: Shortly press to check speed mode status, continue for switching speed mode. B.Accelerator rocker: 1.Push forward to accelerate, pull backward to decelerate and brake. 2.
Remote pairing buttons:B+A Turn on remote and press the Accelerator rocker ( B), you can hear a sound then pull it backward, mean while shortly press power button (A) and release to go into bluetooth pairing mode. Remote pairing introduction: With the skateboard power on, press the power button on skateboard for 3s-5s till you hear the beep means the skateboard is in bluetooth pairing mode. Turn on remote and press the remote pairing buttons (as above) till it slowly flashes means pairing successful.
5-1-2 Power button: Press the power button and hear the beep, battery display lights on means the board was turned on. （Figure 7） Charge the battery before using skateboard (Check 3-3). 5-2 Turn on remote control and start operation 5-2-1. Press the power switch of the remote control for 3-5s to turn on the remote control. Press the power button for 3-5 seconds or leave the board for 3 minutes and it will automatically turn off.
5-3 Pairing With the skateboard power on, press the power button for 3s-5s till hear the beep, release the button while battery light flashing, means it is in the pairing mode. Turn on the remote control, press the button for 3s-5s then you can hear the sound, means pairing successful and the logo start slowly flashing. 5-4 Switch direction witch the back and forward button while pause status to change direction, push the remote accelerator rocker to operate.
VI. Operating limits It is important that you are familiar with the limits of skateboard, which to maximize rider’s safety and reduce the risk of damaging skateboard. The skateboard will perform better when you observe these limits.
VII. Troubleshooting If your skateboard is not running properly, stop using it immediately. In most cases, turning the skateboard off for ten seconds and restarting it will solve the issue. If you find other problems, or restarting the skateboard doesn’t resolve the issue, refer to the following chart for common troubleshooting methods. If the problem still exists, please stop using the skateboard and contact enSkate.
※ Replacable tire and motor PU tires replacement instruction: Loosen 6 screws with hexwrench then pull out the PU tire, insert the new one into the motor hub, and tighten the screws to complete the replacement. Motor replacement instruction: 1. Turn off the skateboard, unplug the waterproof cable, remove the screws, replace by new motor and secure the screws. 2. Follow the alignment mark on the waterproof plug and insert the connector to assuring correct mating.
B. Riding Instruction And Tips 1. In any case, we always recommend using remote control. 2. Switch to APP control or cruise control mode only after you got familiar with skateboard. 3. Emergency brake while riding with high-speed is dangerous, you may need to rely on skating techniques like foot-braking for a gently brake. 4. You can always loose the throttle before the brake. C. Age, Weight & Health 1. Skateboard is not designed for riders under 16. Keep skateboard away from children, young teens. 2.
IX. Maintenance and repair 9-1 Clean ※ For your safety and to avoid potential safety problems, do not wash the board directly with water, only use damp cloth to clean the surface. ※ It is strictly forbidden clean all the sliding interface by damp cloth, including battery connector, battery output interface and etc. 9-2 Maintenance ※ Termly check if the screws loose. ※ For storage, stored the board in a dry and ventilated environment, do not in the sun or hot and humid environment.
This limited warranty is valid only for the original purchaser of a product, and it cannot be transferred to another person upon the sale, lease, or transfer of the product. This limited warranty does not cover normal wear and tear. Belts, bearings, wheels, and grip tape are normal wear and tear items and are not covered under warranty.
FCC Notice: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installati on. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
