2 MP Series Turret & Dome Camera User Manual User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual may contain several technical mistakes or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
Keep the camera away from liquid while in use for non-water-proof device. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark Description DC Voltage 1 Introduction 1.1 Product Features The main features are as follows: High performance CMOS sensor Auto white balance Smart IR 3-Axis Adjustment 1.2 Overview 1.2.
Main Body Enclosure Trim Ring Switch Button Mounting Base I N D C1 2V Power Cord Video Cable Figure 1-4 Overview of Type II Camera Note: Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS. 1.2.3 Overview of Type III Camera Enclosure Main Body Power Cord Video Cable Mounting Base Figure 1-5 Overview of Type III Camera Note: This camera is TVI only.
1.2.5 Overview of Type V Camera Mounting Base Clip Plate Enclosure Main Body Switch Button IN DC 12 V Power Cord Video Cable Figure 1-8 Overview of Type V Camera Note: Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS. 1.2.6 Overview of Type VI Camera Black Liner Adjusting Screws IR Zoom Camera Module Power Cord Video Cable Bubble Figure 1-9 Overview of Type VI Camera Note: This camera is TVI only.
2 Installation Before you start Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the installation environment. Check whether the power supply is matched with your power output to avoid the damage. Make sure the wall is strong enough to withstand three times the weight of the camera, and the mount.
4. Route the cables through the cable hole, or the side opening. 5. Secure the camera on the mounting base. 1) Pull out the clip plate, and then to combine the camera with the mounting base. 2) Push the clip plate in, and secure the camera by tightening the screw. Figure 2-3 Secure the Camera 6. Connect the corresponding power cord, and video cable. 7. Power on the camera to check whether the image on the monitor is gotten from the optimum angle.
For cement wall/ceiling, expansion bolts are required to fix the camera. For wooden wall/ceiling, self-tapping screws are required. 4. Route the cables through the cable hole, or the side opening. 5. Install the camera back to the mounting base and secure them with the trim ring. Figure 2-6 Install the Camera back 6. Connect the corresponding power cord, and video cable. 7. Power on the camera to check whether the image on the monitor is gotten from the optimum angle.
Note: The supplied screw package contains self-tapping screws, and expansion bolts. 5. Route the cables through the cable hole, or the side opening. 6. Install the camera back to the mounting base and secure it. Figure 2-10 Install the Camera Back 7. Connect the corresponding cables, such as power cord, and video cable. 8. Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the camera according to the figure below to get an optimum angle.
Tilt Position [0°to70°] Pan Position [0° to 350°] Rotation Position [0° to 350°] Figure 2-14 3-Aixs Adjustment 7. Install the black liner and the bubble back.
3 Menu Description Please follow the steps below to call the menu. Note: The actual display may vary with your camera model. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. TVI DVR Camera Monitor Figure 3-1 Connection 2. Power on the camera, TVI DVR, and the monitor to view the image on the monitor. 3. Click PTZ Control to enter the PTZ Control interface. 4. Call the camera menu by clicking button, or call the preset No. 95.
5. Click the direction arrow to control the camera. 1). Click up/down direction button to select the item. 2). Click Iris + to confirm the selection. 3). Click left/right direction button to adjust the value of the selected item. 3.1 VIDEO FORMAT You can set the video format to 2MP@30fps, 2MP@25fps, PAL or NTSC. Note: When switching the video output to TVI/ CVI/ AHD, you can set the video format to 2MP@30fps or 2MP@25fps; when switching the video output to CVBS, you can set the video format to PAL or NTSC.
DAY/NIGHT MODE IR LIGHT SMART IR BACK EXIT SAVE & EXIT B&W ON 1 Figure 3-3 B&W IR LIGHT You can turn on/off the IR LIGHT to meet different circumstances. SMART IR The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure. The higher the value is, the more obvious effects are. AUTO Automatically switch Color, or BW (Black and White) according to actual scene brightness.
VIDEO SETTINGS IMAGE MODE WHITE BALANCE BRIGHTNESS CONTRAST SHARPNESS SATURATION DNR MIRROR BACK EXIT SAVE & EXIT STD 5 5 5 5 5 OFF Figure 3-5 VIDEO SETTING IMAGE MODE IMAGE MODE is used to adjust the image saturation, and you can set it to STD (Standard) or HIGH-SAT (High Saturation). WHITE BALANCE White balance, the white rendition function of the camera, is to adjust the color temperature according to the environment. It can remove unrealistic color casts in the image.
HV: The image flips 180° both horizontally and vertically. 3.5 FACTORY DEFAULT Reset all the settings to the factory default. 3.6 EXIT Move the cursor to EXIT and click Iris+ to exit the menu. 3.7 SAVE & EXIT Move the cursor to SAVE & EXIT and click Iris+ to save the settings, and exit the menu.
