User Manual

If you did NOT use Installer Toolkit to build arrays and scan device serial
numbers, create the virtual array in Array Builder using the installation map
as your reference. (You may need to wait if the devices have not yet reported
to Enlighten.)
Method B // If the IQ Envoy is NOT associated with a system in
Installer Toolkit
A ) Log into Enlighten and click Add a New System from the dashboard.
B ) Enter the System, Installer, Owner, and Location information.
C ) Enter the IQ Envoy serial number.
D ) Click Save to submit the form.
E ) After the devices have reported to Enlighten, open Array Builder from the
activation form, and create the virtual array, using the installation map
as your reference.
Activate Monitoring
Register the IQ Envoy in Enlighten (enlighten.enphaseenergy.com).
Method A // If the IQ Envoy is associated with a system in Installer Toolkit
A ) On your mobile device, go to Settings and disconnect from the Envoy’s
AP Wi-Fi network.
B ) Return to the Installer Toolkit app and tap the Sync button on the Sys-
tem Overview screen.
C ) When you have access to a computer, log in to Enlighten and select the
system name from the Activation List on the dashboard.
D ) From the activation form, open Array Builder.
If you used Installer Toolkit to build arrays and scan device serial numbers,
the array(s) are built —make any necessary adjustments in Array Builder.
Send System Summary Report
When you have completed your system setup, you can generate and email a
summary report.
A ) From Installer Toolkit, tap Done in the upper-right corner of the screen to
disconnect from the Envoy. Installer Toolkit will ask if you want to view a
summary report.
B ) Tap View Report. The report displays IQ Envoy and system information
with a list of device serial numbers, their last power reports, and infor-
mation about the grid prole applied to the microinverters.
C ) Tap to email the report to your ofce as a record of successful sys-
tem installation or to the utility for evidence of grid prole settings.
Connect to Enlighten
This section describes using the IQ Envoy integrated Wi-Fi or the Mobile
Connect modem. For information about using Ethernet and/or PLC bridg-
es, refer to the Enphase IQ Envoy Installation and Operation Manual at:
enphase.com/support.
Method A // Integrated Wi-Fi
Requires a wireless router with an Internet connection.
A ) On the Envoy, verify that no Ethernet cable is plugged into the RJ45
port.
B ) If the router supports WPS, press and hold the WPS button on the
wireless router for a few seconds. On most routers, a WPS indicator
begins ashing.
C ) If you are using the Installer Toolkit mobile app, tap the Network
button, tap Wi-Fi, and then tap your network from the list of available
networks. If the wireless
router does not support
WPS, you may be prompted
to enter a password.
The Network Communica-
tions LED
begins ashing
green. Within three minutes the
Network Communications LED lights solid green, indicating a successful
connection to Enlighten. If the Network Communications LED remains off
or lights solid amber, see Troubleshooting
d
.
Method B // Enphase Mobile Connect Modem
(Order CELLMODEM-01 separately)
A ) Connect the antenna(s) to the modem, and mount the modem as
described in the Enphase Mobile Connect Installation Guide.
B ) First, connect the USB cable to the IQ Envoy and then connect the
mini-USB connector to the modem. If receiving power from the IQ
Envoy, the modem power LED lights.
Within three minutes the Network Communications LED lights solid green,
indicating a successful connection to Enlighten.
If the Network Communications LED remains off
or lights solid amber, see Troubleshooting in the
Enphase Mobile Connect Installation Guide.
Method C // Power Line Communication Bridges
(Order EPLC-01 separately)
Requires a broadband router with an Internet connection.
A ) Plug one of the bridges into the AC outlet in the IQ Combiner.
B ) Place the ferrite bead on the cable, near one end, and close the latch.
C ) Plug the cable end with the ferrite into the IQ Envoy Ethernet port, and
secure a tie wrap on the cable on each side of the ferrite bead.
D ) Tighten an additional tie wrap around the ferrite bead.
E ) Trim any tie wrap excess.
F ) Plug the other end of the Ethernet cable into the bridge.
G ) Plug the other bridge into an AC outlet near the broadband router.
H ) Connect one end of a second Ethernet cable to the second bridge,
and connect the other end of the cable into the broadband router.
Within three minutes the Network Communications LED
lights solid
green, indicating a successful connection to the Internet and to Enlighten.
wireless router
IQ Envoy
Enphase
Mobile
Connect
IQ Envoy
Re-torque Connections and Secure the Door
A ) Turn off power to IQ Combiner at the main load center. Verify that all
power is removed from the system before attempting any wiring.
B ) Open the IQ Combiner door.
C ) Remove the clear plastic dead front, and keep the screws and washers
in a safe place.
D ) Measure voltage L1 to L2, L1 to N, and L2 to N to make sure there is no
voltage present.
E ) Re-torque all eld wiring connections, and busbar side of output terminal
blocks (if a breaker was removed), one hour after rst torque.
F ) Close and secure the door of the IQ Combiner so that it is protected
against moisture and rain.
11
12
13
Note: If you do not use the 5A AC outlet in the Combiner, you can re-
quest a cover for the outlet from enphase.com/en-us/support/contact.
14
DANGER! Risk of arcing over time. Do not skip this step.
You must re-torque all eld wiring connections after one
hour.