User's Manual
Table Of Contents
- 1 General description
- 2 Functional overview
- 2.1 Product description
- 2.2 Functional modes
- 2.3 Reporting interval
- 2.3.1 Energy considerations
- 2.3.2 Standard reporting interval
- 2.3.3 Illumination-controlled reporting interval
- 2.3.4 Temperature-controlled reporting interval
- 2.3.5 Humidity-controlled reporting interval
- 2.3.6 Acceleration-controlled reporting interval
- 2.3.7 Magnet contact sensor-controlled reporting interval
- 2.3.8 Arbitration between reporting intervals
- 3 Sensor functionality
- 4 Product interface
- 5 Radio communication
- 6 Security
- 7 Commissioning
- 8 NFC interface
- 9 NFC registers
- 9.1 NFC memory areas
- 9.2 Device identification NDEF
- 9.3 User information NDEF
- 9.4 NFC HEADER
- 9.5 CONFIGURATION
- 9.5.1 Using the NFC configuration functionality
- 9.5.2 CONFIGURATION area structure
- 9.5.3 NFC_PIN_CODE
- 9.5.4 PRODUCT_ID
- 9.5.5 USER_KEY
- 9.5.6 SECURITY_KEY_MODE
- 9.5.7 SECURITY_MODE
- 9.5.8 EEP
- 9.5.9 SIGNAL
- 9.5.10 LED_MODE
- 9.5.11 FUNCTIONAL_MODE
- 9.5.12 STANDARD_TX_INTERVAL
- 9.5.13 THRESHOLD_CFG1
- 9.5.14 THRESHOLD_CFG2
- 9.5.15 LIGHT_SENSOR_CFG
- 9.5.16 ACC_SENSOR_CFG
- 9.5.17 SOLAR_THRESHOLD
- 9.5.18 SOLAR_TX_INTERVAL
- 9.5.19 LIGHT_THRESHOLD
- 9.5.20 LIGHT_TX_INTERVAL
- 9.5.21 ACCELERATION_THRESHOLD
- 9.5.22 ACCELERATION_TX_INTERVAL
- 9.5.23 TEMPERATURE_THRESHOLD
- 9.5.24 TEMPERATURE_TX_INTERVAL
- 9.5.25 HUMIDITY_THRESHOLD
- 9.5.26 HUMIDITY_TX_INTERVAL
- 9.5.27 MAGNET_CONTACT_TX_INTERVAL
- 9.5.28 ILLUMINATION_TEST_RESULT
- 9.6 USER DATA
- 10 Mechanical interface
- 11 Installation recommendations
- 12 Regulatory notes
- 13 Product history
USER MANUAL
STM 550 / EMSI – ENOCEAN MULTISENSOR FOR IOT APPLICATIONS
© 2020 EnOcean | www.enocean.com F-710-017, V1.0 STM 550 / EMSI User Manual | v1.4 | November 2020 | Page 8/97
1.2 Product variants
STM 550 is available in three different product and packaging variants:
◼ STM 550 is the multisensor module in original PTM module form factor intended for
integration into OEM housings. It is provided in tray and box packaging of 100 units
per box.
◼ STM 550 Installation Kit combines the STM 550 multisensor module with a wall
mount, a design frame, a magnet (for magnet sensor functionality) and an adhesive
mounting tape into a ready to use product. It is provided in tray and box packing of
100 units per box.
◼ EMSI Easyfit Multisensor contains the same components as STM 550 Installation Kit
but is provided in single unit packaging with 10 single packaged units per box.
Figure 1 below shows the STM 550 module on the left and the finished product combining
the STM 550 module with wall mount and design frame on the right.
Figure 1 – STM 550 module (left) and finished product (right)