User's Manual
Table Of Contents
- 1 General description
- 2 Functional overview
- 2.1 Product description
- 2.2 Functional modes
- 2.3 Reporting interval
- 2.3.1 Energy considerations
- 2.3.2 Standard reporting interval
- 2.3.3 Illumination-controlled reporting interval
- 2.3.4 Temperature-controlled reporting interval
- 2.3.5 Humidity-controlled reporting interval
- 2.3.6 Acceleration-controlled reporting interval
- 2.3.7 Magnet contact sensor-controlled reporting interval
- 2.3.8 Arbitration between reporting intervals
- 3 Sensor functionality
- 4 Product interface
- 5 Radio communication
- 6 Security
- 7 Commissioning
- 8 NFC interface
- 9 NFC registers
- 9.1 NFC memory areas
- 9.2 Device identification NDEF
- 9.3 User information NDEF
- 9.4 NFC HEADER
- 9.5 CONFIGURATION
- 9.5.1 Using the NFC configuration functionality
- 9.5.2 CONFIGURATION area structure
- 9.5.3 NFC_PIN_CODE
- 9.5.4 PRODUCT_ID
- 9.5.5 USER_KEY
- 9.5.6 SECURITY_KEY_MODE
- 9.5.7 SECURITY_MODE
- 9.5.8 EEP
- 9.5.9 SIGNAL
- 9.5.10 LED_MODE
- 9.5.11 FUNCTIONAL_MODE
- 9.5.12 STANDARD_TX_INTERVAL
- 9.5.13 THRESHOLD_CFG1
- 9.5.14 THRESHOLD_CFG2
- 9.5.15 LIGHT_SENSOR_CFG
- 9.5.16 ACC_SENSOR_CFG
- 9.5.17 SOLAR_THRESHOLD
- 9.5.18 SOLAR_TX_INTERVAL
- 9.5.19 LIGHT_THRESHOLD
- 9.5.20 LIGHT_TX_INTERVAL
- 9.5.21 ACCELERATION_THRESHOLD
- 9.5.22 ACCELERATION_TX_INTERVAL
- 9.5.23 TEMPERATURE_THRESHOLD
- 9.5.24 TEMPERATURE_TX_INTERVAL
- 9.5.25 HUMIDITY_THRESHOLD
- 9.5.26 HUMIDITY_TX_INTERVAL
- 9.5.27 MAGNET_CONTACT_TX_INTERVAL
- 9.5.28 ILLUMINATION_TEST_RESULT
- 9.6 USER DATA
- 10 Mechanical interface
- 11 Installation recommendations
- 12 Regulatory notes
- 13 Product history
USER MANUAL
STM 550 / EMSI – ENOCEAN MULTISENSOR FOR IOT APPLICATIONS
© 2020 EnOcean | www.enocean.com F-710-017, V1.0 STM 550 / EMSI User Manual | v1.4 | November 2020 | Page 69/97
9.5.21 ACCELERATION_THRESHOLD
If reduction of the reporting interval based on acceleration has been enabled then the ac-
celeration threshold is defined by ACCELERATION_THREHOLD register as shown in Figure
48 below.
Note that this threshold is also used for the wake-on-acceleration function as described in
chapter 3.5.
ACCELERATION _THRESHOLD
Bit 15
Bit 14
…
Bit 1
Bit 0
ACCELERATION THRESHOLD
Figure 48 – ACCELERATION _THRESHOLD register
The encoding used by the ACCELERATION THRESHOLD bit field is shown in Table 33 below.
ACCELERATION THRESHOLD
Threshold
0b000000
Reserved (Do not use)
0b000001 (Default)
1/64 * Full scale
0b000010
2/64 * Full scale
…
0b111110
62/64 * Full scale
0b111111
63/64 * Full scale
Table 33 – ACCELERATION THRESHOLD bit field encoding