USER MANUAL V1.0 Pushbutton Transmitter Device PTM 215Z September 17, 2013 Patent protected: US 6,747,573 US 7,019,241 Further patents pending EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone +49.89.67 34 689-0 Fax +49.89.67 34 689-50 info@enocean.com www.enocean.com Subject to modifications PTM 215Z User Manual | v1.
USER MANUAL V1.0 PTM 215Z REVISION HISTORY The following major modifications and improvements have been made to the first version of this document: No 1.0 Major Changes Initial Release Published by EnOcean GmbH, Kolpingring 18a, 82041 Oberhaching, Germany www.enocean.com, info@enocean.com, phone ++49 (89) 6734 6890 © EnOcean GmbH All Rights Reserved Important! This information describes the type of component and shall not be considered as assured characteristics.
USER MANUAL V1.0 PTM 215Z TABLE OF CONTENT 1 GENERAL DESCRIPTION .................................................................................... 4 1.1 Basic Functionality ........................................................................................... 4 1.2 Typical Applications .......................................................................................... 5 1.3 Technical Data ................................................................................................. 5 1.
USER MANUAL V1.0 PTM 215Z 1 GENERAL DESCRIPTION The radio transmitter device PTM 215Z from EnOcean enables the implementation of wireless remote controls without batteries. Power is provided by a built-in electro-dynamic power generator. The PTM 215Z device transmits data based on the 2.4GHz ZigBee Green Power standard. The outer appearance of PTM 215Z is shown on the picture below.
USER MANUAL V1.0 PTM 215Z The PTM 215Z radio telegram identifies the status (pressed or not pressed) of the four contact nipples (2) when the energy bow was pushed or released. This enables the implementation of up to two switch rockers or up to four pushbuttons. 1.
USER MANUAL V1.0 PTM 215Z PTM 215Z without antenna, tilted view (including rocker catwalks) 1) these catwalks are not needed when using one single rocker only 2) dimensions of rocker part PTM 215Z, top view (note cut A, B and C marking) EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone +49.89.67 34 689-0 Fax +49.89.67 34 689-50 info@enocean.com www.enocean.com Subject to modifications PTM 215Z User Manual | v1.
USER MANUAL V1.0 PTM 215Z PTM 215Z, cut A 2) dimensions of rocker part PTM 215Z, cut B and C EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone +49.89.67 34 689-0 Fax +49.89.67 34 689-50 info@enocean.com www.enocean.com Subject to modifications PTM 215Z User Manual | v1.
USER MANUAL V1.0 PTM 215Z Hatched areas: support planes PTM 215Z rear view EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone +49.89.67 34 689-0 Fax +49.89.67 34 689-50 info@enocean.com www.enocean.com Subject to modifications PTM 215Z User Manual | v1.
USER MANUAL V1.0 PTM 215Z 2) dimensions of rocker part PTM 215Z, side view If the rocker is not mounted on the rotation axis of PTM 215Z several tolerances have to be considered! The measure from support plane to top of the energy bow is 7.70 mm +/- 0.3 mm! The movement of the energy bow must not be limited by mounted rockers! Catwalks of the switch rocker must not exert continuous forces on contact nipples! EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone +49.89.67 34 689-0 Fax +49.89.
USER MANUAL V1.0 PTM 215Z 1.5 Environmental Conditions Operating temperature Storage temperature Humidity 1.6 -5 °C up to +45 °C -25 °C up to +65 °C 0% to 95% r.h., non-condensing Ordering Information Type PTM 215Z EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Ordering Code S3071-A215 Phone +49.89.67 34 689-0 Fax +49.89.67 34 689-50 info@enocean.com www.enocean.com Subject to modifications PTM 215Z User Manual | v1.
USER MANUAL V1.0 PTM 215Z 2 2.1 FUNCTIONAL DESCRIPTION Block Diagram Data Status Processor HF Contact Nipples Pushed/Released Ant DC Power Energy Bow N S Power Converter Block diagram of PTM 215Z Energy Bow / Power Generator Converts the motion of the energy bow into electrical energy. Power Converter Converts the energy of the power generator into a stable DC supply voltage for the device electronics.
USER MANUAL V1.0 PTM 215Z 2.2 Contact Nipples Designation PTM 215Z devices provide four contact nipples. They are grouped into two channels (Channel A and Channel B) each containing two contact nipples (State O and State I). The state of all four contact nipples (pressed or not pressed) is transmitted together with a unique device identification (fixed 32-bit ZGPD SrcId) whenever the energy bow is pushed or released.
USER MANUAL V1.0 PTM 215Z 2.3.1 Normal Mode In normal mode, PTM 215Z transmits secure data telegrams reflecting the state of the four device buttons whenever the energy bar is pressed or released. The state of the four buttons is encoded in one data byte of payload. The data telegrams sent when the energy bar is pressed are different from the ones sent when the energy bar is released.
USER MANUAL V1.0 PTM 215Z 2.3.2 Commissioning Mode In order to join an existing ZigBee Green Power compliant network, PTM 215Z devices need to be configured for the correct radio channel and subsequently issue a properly formatted “Join” request outlining its device and security parameters. The combination of these tasks is referred to as commissioning. 2.3.2.1 Radio Channel Selection PTM 215Z devices support up to four pre-configured, dynamically selectable radio channels.
USER MANUAL V1.0 PTM 215Z 2.4 Construction of application specific Switch Rockers For CAD system development support, 3D construction data is available from EnOcean (IGS data). Using this data, the mechanical interface is fixed, and the shape and surface of the rocker(s) can be changed according to requirements. Polycarbonate is recommended as rocker material since it is both buckling resistant and wear-proof. It is also recommended to apply Teflon varnish in the areas of actuation.
USER MANUAL V1.0 PTM 215Z 2.6 Regulatory Notes PTM 215Z has been certified according to applicable regulations. Changes or modifications not expressly approved by EnOcean could void the user's authority to operate the equipment. 2.6.1 FCC (United States) Regulatory Statement This device complies with part 15 of the FCC Rules.
USER MANUAL V1.0 PTM 215Z 3 Transmission Range The main factors that influence the system transmission range are: - Type and location of the antennas of receiver and transmitter - Type of terrain and degree of obstruction of the link path - Sources of interference affecting the receiver - “Dead spots” caused by signal reflections from nearby conductive objects.
