Operator`s manual

ON/OFFON/OFF
R
Amp
Tube
FOOTPEDAL
Z-4
Your Options for controlling the ENGL Raider 100 amp remotely:
#1 ENGL Z-9 Custom Footswitch: This specialized footboard connects to the amp
via a 6.3 mm (¼”) stereo cord plugged into the Serial Amp Port - S.A.C. (34).
The Z-9 affords you direct access to the amp's four gain stages (CH 1 / CH 2 merged
with Hi Gain) simply by tapping the four channel switching buttons, and lets you
control two special functions, for example, Mid Boost and Reverb.
#2 A two-way footswitch such as the ENGL Z-4: Connect
dual footswitches to the amp by plugging stereo 6.3 mm
(¼”) cords into jack nos. 35, 36, and 37.
-> CH 1 / CH 2 (Channel 1 / 2) and Hi Gain (1 x Z-4);
-> Master A/B and Mid Boost (1 x Z-4);
-> Main FX Loop and Reverb (1 x Z-4);
As an alternative to dual footswitches, you can connect
a MIDI switcher (the ENGL Z-11 will do nicely) to these
three jacks to control the six switching functions.
#2
#1
R
Amp
Technology
Tube
Custom
Footswitch
Z-9
Ser.Cnt.:
Channel 1
Ser.Cnt.:
Channel 2
Ser.Cnt.:
Channel 3
Ser.Cnt.:
Channel 4
Ser.Cnt.:
Function 1
Ser.Cnt.:
Function 2
MIDI:
Patch 1/6
MIDI:
Patch 2/7
MIDI:
Patch 3/8
MIDI:
Patch 4/9
MIDI:
Patch 5/10
MIDI:
Bank A/B
Power Supply In
7-14 Volts AC
9-20 Volts DC
approx. 100 mA
MIDI
Out
Serial Amp
Control Out
Caution !
Connect To
Amplifier
Only!
Design by
Horst Langer
To assign Amp switching
features to the Function
1 and 2 button, press the
Channel 1 and the
respective Function button
simultaneously until the
LED starts flashing.
Now use the buttons
1 to 4 to select
the desired switching
feature (press 1x or 2x).
Store the selected
switching feature by
pressing the opposite
Function button
for approx. 1 second.
Poweramp Output
Serial Amp
Control Port
CA
UTION:
Connect Custom
Footswitch Z-9 Only!
CH 1 / CH 2
Hi Gain
R EPLACE F USE
O NLY W ITH S AME
T YPE A ND R ATING !
Main FX Loop
Send Return
Threshold
Level
Off max.
Noise Gate Serial FX Loop
Send ReturnBalance
Dry Effect
Footswitch
8 Ohms Parallel
1 x 8 Ohms or 2 x 16 Ohms
16 Ohms4 Ohms Parallel
1 x 4 Ohms or 2 x 8 Ohms
Master A/B
Mid Boost
FX Loop
R everb
S.A.C. Port
D O N OT O PEN !
R ISK O F E LECTRIC S HOCK !
D O N OT E XPOSE T HIS E QUIPMENT
T O R AIN O R M OISTURE !
CAUTION !
!
All-tube
Guitar Combo Amp
RAIDER 100
TYPE E344
Am
p-Design by
Horst Langer
MADE IN GERMANY
R
Amp
Tube
#1 #2 #2 #2
Wiring of Principal Connectors
Stereo
1/4" jack
Serial Amp Control Port (34)
tip: + 5 volts
ring: Data
sleeve: Ground, GND
Very important:
use a stereo
plug only!
Connect ENGL
Custom Z-9
Footswitch only!
Stereo
1/4" jack
Dual Footswitch (35, 36, 37)
tip: refer to *3
ring: refer to *2
sleeve: Ground, GND
Use a stereo
plug only!
page: 14, 15
Stereo
1/4" plug
ring
tip
sleeve
Here you'll find at a glance the technical details
of the Raider 100's various remote switching capabilities:
*2: A switch connected to this terminal controls
Reverb - off <-> on via jack (35)
Mid Boost - passive <-> active via jack (36)
Hi Gain - Lo Gain <-> Hi Gain via jack (37)
*3: A switch connected to this terminal controls
Main FX Loop - off (bypassed) <-> on (enabled) via jack (35)
Master A/B - Master A <-> Master B via jack (36)
CH 1 / CH 2 - Channel 1 <-> Channel 2 via jack (37)
page: 14
24