Wireless Outdoor Access Point / Client Bridge M5000 User Manual Version : V1.
Table of Contents 1 PRODUCT OVERVIEW ........................................................................................................................................................... 3 1.1 FEATURE......................................................................................................................................................................... 3 1.2 BENEFITS .........................................................................................................................
4.6 WIRELESS → WDS LINK SETTINGS.................................................................................................................................. 34 5 LAN SETTINGS ..................................................................................................................................................................... 35 5.1 SYSTEM → IP SETTINGS .........................................................................................................................................
APPENDIX A – FCC INTERFERENCE STATEMENT .................................................................................................................... 75 1 Product Overview Thank you for using M5000. It is a powerful, enhanced, enterprise scale product with 5+1 multi-functions Access Point, Access Point with WDS function, Client Bridge, WDS Bridge, Client Router, and Mesh. M5000 is easily to install almost anywhere with Power over Ethernet for quick outdoor installation.
Show rooms, meeting rooms, retail stores, and manufacturing sites where frequently rearrange the workplace. e) Wireless extensions to Ethernet networks Network managers in dynamic environments can minimize the overhead caused by moves, extensions to networks, and other changes with wireless LANs. f) Wired LAN backup Network managers implement wireless LANs to provide backup for mission-critical applications running on wired networks.
1.2 Benefits Access Point Mode Use this feature to setup the access point’s configuration information. It has support adjusting transmit power and channel. Client can access the network with different regulatory settings and automatically change to the local regulations. Client Bridge Mode Use this feature to connect to an Access Point and enjoy the great speed of surfing internet. WDS Bridge Mode Use this feature to link multiple APs in a network.
1.3 Package Contents Open the package carefully, and make sure that none of the items listed below are missing. Do not discard the packing materials, in case of return; the unit must be shipped in its original package. 1* Wireless Outdoor Access Point / Client Bridge (M5000) 1* 24V/1A Power Adapter 1* Ethernet Cable 1* QIG 1* CD (User Manual) 1* 5dBi Dipole Antennas Auction: Using other Power Adapter than the one included with M5000 may cause damage of the device. 1.
• Red: Bad Quality Power Requirements Active Ethernet (Power over Ethernet) Proprietary PoE design Power Adapter 24V / 1A DC Regulation Certifications FCC Part 15C/15B/15E, EN301 893, EN 300 328, EN 301 489-1/-17, EN60950, IC Certification 7
2 M5000 Multi-Function Instruction Guide 2.1 Access Point In the Access Point Mode with WDS Function, M5000 function likes a central connection for any stations or clients that support IEEE 802.11a network. Stations and Client must configure the same SSID and Security Password to associate within the range. M5000 supports 4 different SSIDs to separate different clients at the same time. 2.
2.3 Client Bridge In the Client Bridge Mode, the M5000 function likes a wireless dongle. Connected to an Access Point wirelessly and surf internet whenever you want. Using Site Survey to scan all the Access Point within the range and configure its SSID and Security Password to associate with it. Connect you station to the LAN port of the M5000 via Ethernet. 2.
2.5 Client Router In the Client Router Mode, the M5000 has DHCP Server build inside that allows many LANs automatically generate an IP address to share the same Internet. Connect an AP/WISP Wirelessly and connect to LANs via wired. Client Router Mode is act completely opposite to the AP Router Mode. 2.6 Mesh In the Mesh Mode, the M5000 is act like an independent node and each node is allowed connecting to another network.
11
3 Computer Settings 3.1 Assign a Static IP In order to configure M5000, please follow the instruction below: 1. In the Control Panel, double click Network Connections and then double click on the connection of your Network Interface Card (NIC). You will then see the following screen. 2. Select Internet Protocol (TCP/IP) and then click on the Properties button. This will allow you to configure the TCP/IP settings of your PC/Notebook 3.
3.2 Logging Method After complete the IP settings from last section, you can now access the web-based configuration menu. 1. Open web browser 2. Enter IP 192.168.1.1 into you address filter. Auction: If you have changed the M5000 LAN IP address, make sure you enter the correct IP Address. 3. After connected to the M5000 successfully, browser will pop out a Windows Security window. Please enter the correct Username and Password. 4. The default Username and Password are both admin.
4 Wireless Settings 4.1 Switching Operation Mode (System → System Properties) The M5000 supports 4 different operation modes: Access Point, Client Bridge, WDS Bridge, and Client Router. Click System Properties under System Section to begin. . Device Name: Specify a name for the device, but it is not the broadcast SSID. It will be shown in SNMP management. Country/Region: Select a Country/Region to conform local regulation. Operation Mode: Select an operation mode via Radio Button.
Mode and then enable WDS Link Settings function. 4.2 Wireless Settings 4.2.1 Access Point Mode → Wireless Network Wireless Mode M5000 supports 802.11a/b/g wireless band. Channel / Frequency The channel availability is based on the country’s regulation. Auto Place a Check to enable Auto channel selection. AP Detection AP Detection can help to select a best channel by scan nearby area.
supports 5GHz network can associate with. Please make sure your wireless client supports 5GHz wireless network. Note: Enable Profile Isolation will cause wireless clients cannot communicate each other. For more details please refer to the “VLAN Management Configuration Guide. SSID Specify the SSID for current profile. VLAN ID Specify the VLAN tag for current profile. Suppressed SSID Place a Check to hide the SSID. Client will not be able to see the broadcast SSID in Site Survey.
4.2.2 Client Bridge Mode → Wireless Network Wireless Mode M5000 supports 802.11a wireless band. SSID Specify the SSID if known. SSID text box will be automatically fill in when select an AP in the Site Survey. Site Survey Using Site Survey to scan nearby APs and then select the AP to establish the connection. Prefer BSSID Specify the MAC address if known. Prefer BSSID text box will be automatically fill in when select an AP in the Site Survey.
filled in manually. 4.2.3 WDS Bridge Mode → Wireless Network Wireless Mode M5000 supports 802.11a wireless band. Channel / Frequency The channel availability is based on the country’s regulation. Apply / Cancel Press Apply to apply the changes or Cancel to return previous settings.
MAC Address Enter the Access Point’s MAC address that you would like to extend the wireless area into the MAC address filter. Mode Select Disable or Enable from the drop down list. Apply / Cancel Press Apply to apply the changes or Cancel to return previous settings. Auction: The Access Point that you would like to extend the wireless area must enter your Access Point’s MAC address. Not all Access Point supports this feature. More WDS bridges connected together may cause lower performance.
4.2.4 Client Router Mode → Wireless Network Wireless Mode M5000 supports 802.11a wireless band. SSID Specify the SSID if known. SSID text box will be automatically fill in when select an AP in the Site Survey. Site Survey Using Site Survey to scan nearby APs and then select the AP to establish the connection. Prefer BSSID Specify the MAC address if known. Prefer BSSID text box will be automatically fill in when select an AP in the Site Survey.
4.2.5 Mesh Mode → Wireless Network Wireless Mode M5000 supports 802.11a wireless band. SSID Specify the SSID if known. SSID text box will be automatically fill in when select an AP in the Site Survey. Channel / Frequency The channel availability is based on the country’s regulation. Mesh Profile Place a Check to act like gateway. Press Edit to configure the mesh profile and place a Check to enable extra SSID.
Mesh Profile SSID Specify the name of the Mesh networking. Wireless Security Please refer to the Wireless Security section. Save / Cancel Press Save to save the changes or Cancel to return previous settings. Note: Mesh Mode’s Wireless Security only supports WEP encryption. Auction: The SSID and Security Mode must be the same to the Mesh Network otherwise it cannot join the mesh network Access Point Profile SSID Specify the SSID for current profile. Suppressed SSID Place a Check to hide the SSID.
Auction: M5000 only supports 802.11a (5GHz) wireless mode, only the wireless client which supports 5GHz network can associate with. Please make sure your wireless client supports 5GHz wireless network.
4.3 Wireless Security Settings Wireless Security Settings section will guide you to the entire Security modes configuration: WEP, WPA-PSK, WPA2-PSK, WPA-PSK Mixed, WPA, WPA2, and WPA Mixed. We strongly recommend that uses WPA2-PSK as your security settings. 4.3.1 WEP Security Mode Select WEP from the drop down list to begin the configuration. Auth Type Select Auth Type in Open System or Shared. Input Type Select Input Type in Hex or ASCII.
4.3.2 WPA-PSK Security Mode Select WPA-PSK from the drop down list to begin the configuration. Encryption Select Auto, TKIP or AES for Encryption type. Passphrase Specify the security password. Group Key Update Interval Specify Group Key Update Interval time. Group Key Update Timeout Specify Group Key Update Timeout time. Pairwise Key Update Interval Specify Pairwise Key Update Timeout time. 4.3.3 WPA2-PSK Security Mode Select WPA2-PSK from the drop down list to begin the configuration.
Encryption Select Auto, TKIP or AES for Encryption type. Passphrase Specify the security password. Group Key Update Interval Specify Group Key Update Interval time. Group Key Update Timeout Specify Group Key Update Timeout time. Pairwise Key Update Interval Specify Pairwise Key Update Timeout time. 4.3.4 WPA-PSK Mixed Security Mode Select WPA-PSK Mixed from the drop down list to begin the configuration. Encryption Select Auto, TKIP or AES for Encryption type.
4.3.5 WPA WPA security mode is for 802.1x authentication. You must provide a RADIUS Server to check the permission of access the network. Security Mode Select WPA from the drop down list to begin the configuration. Encryption Select Auto, TKIP or AES for Encryption type. Radius Server Specify Radius Server IP Address. Radius Port Specify Radius Port number, the default port is 1812. Radius Secret Specify Radius Secret that is given by the Radius Server.
4.3.6 WPA2 WPA2 security mode is for 802.1x authentication. You must provide a RADIUS Server to check the permission of access the network. Security Mode Select WPA2 from the drop down list to begin the configuration. Encryption Select Auto, TKIP or AES for Encryption type. Radius Server Specify Radius Server IP Address. Radius Port Specify Radius Port number, the default port is 1812. Radius Secret Specify Radius Secret that is given by the Radius Server.
4.3.7 WPA Mixed WPA Mixed security mode is for 802.1x authentication. You must provide a RADIUS Server to check the permission of access the network. Security Mode Select WPA Mixed from the drop down list to begin the configuration. Encryption Select Auto, TKIP or AES for Encryption type. Radius Server Specify Radius Server IP Address. Radius Port Specify Radius Port number, the default port is 1812. Radius Secret Specify Radius Secret that is given by the Radius Server.
4.3.8 Radius Accounting Radius Accounting function allows you to record the statics of user login. Your Radius Server must have the ability to support Radius Accounting function. Radius Accounting Select Enable to begin configuration of Radius Accounting. Radius Accounting Server Specify Radius Accounting Server IP. Radius Accounting Port Specify Radius Accounting Server IP. The default port is 1813.
4.4 Wireless → Wireless Advanced Settings Data Rate Select Data Rate from the drop down list. Data rate will affect the efficiency of the throughput. If the data rate is set to a small number, the lower through will get but it can transmit to longer distance. Transmit Power Select Transmit Power to increase or decrease Transmit Power. Higher transmit power will sometimes cause unable to connect to the network. On the other hand, the lower transmit power will cause client unable to connect to the device.
may cause lower throughput but less collision. Distance Specify distance rage between AP and Clients. Longer distance may lose high connection speed. Wireless Traffic Shaping Place a Check to enable Wireless Traffic Shaping function. Incoming Traffic Limit Specify the wireless transmission speed for downloading. Outgoing Traffic Limit Specify the wireless transmission speed for uploading. Auction: Changing Wireless Advanced Settings may cause insufficient wireless connection quality.
4.5 Wireless → Wireless MAC Filter Wireless MAC Filters is used to Allow or Deny wireless clients, by their MAC addresses, accessing the Network. You can manually add a MAC address to restrict the permission to access M5000. The default setting is Disable Wireless MAC Filters. 0. ACL Mode ACL Mode can help to deny or allow certain Client to access the network. Select Disable, Deny MAC in the list or Allow MAC in the list from the drop down list. MAC Address Filter Specify the MAC address manually.
4.6 Wireless → WDS Link Settings WDS Link Settings is used to establish a connection between Access Points but the device is not losing Access Point function. AP has WDS function can extend the wireless coverage and allow LANs to communicate each other. MAC Address Enter the Access Point’s MAC address that you would like to extend the wireless area. Mode Select Disable or Enable from the drop down list. Apply / Cancel Press Apply to apply the changes or Cancel to return previous settings.
5 LAN Settings This section will guide you to the Local Area Network (LAN) settings 5.1 System → IP Settings This section is only available for Non-Router Mode. IP Settings allows you to setup LAN port IP address. Auction: Changing LAN IP Address will change LAN Interface IP address. Webpage will automatically redirect to the new IP address after Apply. IP Network Setting Select Radio button for Obtain an IP address automatically or Specify an IP address. IP Address Specify LAN port IP address.
5.2 System → Spanning Tree Settings Spanning Tree Status Select the Radio button to On or Off Spanning Tree function. Bridge Hello Time Specify Bridge Hello Time in second. Bridge Max Age Specify Bridge Max Age in second. Bridge Forward Delay Specify Bridge Forward Delay in second. Priority Specify the Priority number. Smaller number has greater priority. Apply / Cancel Press Apply to apply the changes or Cancel to return previous settings.
6 Router Settings This section is only available for AP Router Mode and Client Router Mode. 6.1 Router → WAN Settings There are four different types of WAN connection: Static IP, DHCP, PPPoE and PPTP. Please contact your ISP to select the connection type. 6.1.1 WAN Settings → Static IP Select Static IP in WAN connection if your ISP gives all the information about IP address, Subnet Mask, Default Gateway, Primary DNS and Secondary DNS.
Internet Connection Type Select Static IP to begin configuration of the Static IP connection. Account Name Specify Account Name that is provided by ISP. Domain Name Specify Domain Name that is provided by ISP. MTU Specify the Maximum Transmit Unit size. Suggest remain in Auto. IP Address Specify WAN port IP address. IP Subnet Mask Specify WAN IP Subnet Mask. Gateway IP Address Specify WAN Gateway IP address. Primary DNS Specify Primary DNS IP. Secondary DNS Specify Secondary DNS IP.
unable to establish some connections. In either case, network performance can suffer.
6.1.2 WAN Settings → DHCP (Dynamic IP) Select DHCP as your WAN connection type to obtain your IP address automatically. You will need to enter Account Name as your hostname and DNS (Optional). Internet Connection Type Select DHCP to begin configuration of the DHCP connection. Account Name Specify Account Name that is provided by ISP. Domain Name Specify Domain Name that is provided by ISP. MTU Specify the Maximum Transmit Unit size. Suggest remain in Auto.
Auction: If the router's MTU is set too high, packets will be fragmented downstream. If the router's MTU is set too low, the router will fragment packets unnecessarily and in extreme cases may be unable to establish some connections. In either case, network performance can suffer.
6.1.3 WAN Settings → PPPoE (Point-to-Point Protocol over Ethernet) Select PPPoE as your WAN connection type if your ISP provides Username and Password. PPPoE is a DSL service and please remove your PPPoE software from your computer, the software is not worked in M5000. Internet Connection Type Select PPPoE to begin configuration of the PPPoE connection. MTU Specify the Maximum Transmit Unit size. Suggest remain in Auto. Login Specify the Username that is given by your ISP.
Connect on Demand Select the Radio button to specify the maximum idle time. Internet connection will disconnect when it reach the maximum idle time, but it will automatically connect when user tries to access the network. Keep Alive Select the Radio button to keep internet connection always on. Specify the redial period once the internet lose connection. Get Automatically From ISP Select the Radio button for get the DNS automatically from DHCP server.
6.1.4 WAN Settings → PPTP (Point-to-Point Tunneling Protocol) Select PPTP as your WAN connection type if your ISP provides information about IP Address, Subnet Mask, Default Gateway (Optional), DNS (Optional), Server IP, Username, and Password. Internet Connection Type Select PPTP to begin configuration of the PPTP connection. MTU Specify the Maximum Transmit Unit size. Suggest remain in Auto.
IP Address Specify WAN port IP address. IP Subnet Mask Specify WAN IP Subnet Mask. Gateway IP Address Specify WAN Gateway IP address. PPTP Server Specify PPTP Server IP address. Username Specify the Username that is given by your ISP. Password Specify the Password that is given by your ISP. Connect on Demand Select the Radio button to specify the maximum idle time.
6.2 Router → LAN Settings IP Address Specify LAN port IP address. IP Subnet Mask Specify LAN IP Subnet Mask. WINS Server IP Specify WINS Server IP. Use Router As DHCP Server Place a Check to enable DHCP server. Starting IP Address Specify DHCP server starting IP address. Ending IP Address Specify DHCP server ending IP address. Apply / Cancel Press Apply to apply the changes or Cancel to return previous settings.
6.3 Router → VPN Pass Through VPN Pass Through is used to allow certain protocol to be tunneled through an IP network such as PPTP and L2TP or implement secure exchange of packets at the IP Layer such as IPSec. PPTP Pass Through Place a Check to enable PPTP protocol passes through WAN. L2TP Pass Through Place a Check to enable L2TP protocol passes through WAN. IPSec Pass Through Place a Check to enable IPSec protocol passes through WAN.
6.4 Router → Port Forwarding Port Forwarding is used to allow a public service such as Web Server, Mail Server, and FTP server to be set up. For example: Set up a Web Server on your computer with port number 8080. Visitor on the internet can access your Web Server by entering WAN Port IP with port number 8080. If your WAN Port IP is 192.168.5.1, then visitor must enter http://192.168.5.1:8080. To find out more the well known port numbers please search the internet.
Ending Port Specify Ending Port number. IP Address Specify IP address. Save / Cancel Press Save to apply the changes or Cancel to return previous settings. 7 Information Status Status section is on the navigation drop-down menu. You will then see three options: Main, Wireless Client List, System Log, WDS Link Status, Connection Status, and DHCP Client Table. Each option is described in detail below. 7.
50
7.2 Status → Wireless Client List Click on the Wireless Client List link under the Status drop-down menu. This page displays the list of Clients that are associated to the M5000. The MAC addresses and signal strength for each client is displayed.
7.3 Status → System Log Click on the System Log link under the Status drop-down menu. The device automatically logs (records) events of possible interest in its internal memory. If there is not enough internal memory for all events, logs of older events are deleted, but logs of the latest events are retained.
7.4 Status → WDS Link Status The WDS Link Status will only show in WDS Bridge Mode. Click on the WDS Link Status link under the Status drop-down menu. This page displays the current status of WDS link, including station ID, MAC address, status and RSSI.
7.5 Status → Connection Status Click on the Connection Status link under the Status drop-down menu. This page displays the current status of the network, including network type, SSID, BSSID, connection status, wireless mode, current channel, security, data rate, noise level and signal strength.
7.6 Status → DHCP Client Table Click on the DHCP Client List link under the Status drop-down menu. This page displays the list of Clients that are associated to the M5000 through DHCP. The MAC addresses and signal strength for each client is displayed. Click on the Refresh button to refresh the client list.
8 Management Settings Management section is on the navigation drop-down menu. You will then see seven options: administration, management VLAN, SNMP settings, backup/restore settings, firmware upgrade, time settings, and log. Each option is described below. 8.1 Management → Administration Click on the Administration link under the Management menu. This option allows you to create a user name and password for the device. By default, this device is configured with a user name and password admin.
Port Port number is 8080, then you will need to enter following http://:8080 to access the web interface. Apply / Cancel Press Apply to apply the changes or Cancel to return previous settings.
8.2 Management → Management VLAN Click on the Management VLAN link under the Management menu. This option allows you to assign a VLAN ID to the packets on wired network. Management VLAN (Wired) is used to manage your device if the computer has authorized VLAN ID. If you would like to use Management VLAN function, you must enable Profile Isolation at Wireless Network section.
8.3 Management → SNMP Settings Click on the SNMP Settings link under the Management menu. This is a networking management protocol used to monitor network-attached devices. SNMP allows messages (called protocol data units) to be sent to various parts of a network. Upon receiving these messages, SNMP-compatible devices (called agents) return data stored in their Management Information Bases. SNMP Enable/Disable Select the Radio button to Enable or Disable SNMP function.
8.4 Management → Backup/Restore Settings Click on the Backup/Restore Setting link under the Management menu. This option is used to save the current settings of the device in a file on your local disk or load settings on to the device from a local disk. This feature is very handy for administrators who have several devices that need to be configured with the same settings.
8.5 Management → Firmware Upgrade Click on the Firmware Upgrade link under the Management menu. This page is used to upgrade the firmware of the device. Make sure that downloaded the appropriate firmware from your vendor. Auction: Upgrade process may take few minutes, please do not power off the device and it may cause the device crashed or unusable. M5000 will restart automatically once the upgrade is completed.
8.6 Management → Time Settings Click on the Time Settings link under the Management menu. This page allows you to configure the time on the device. You may do this manually or by connecting to a NTP server. Manually Set Date and Time Manually setup the date and time. Automatically Get Date and Time address of the NTP Server manually or uses default NTP Server. Apply / Cancel Press Apply to apply the changes or Cancel to return previous settings.
8.7 Management → Log Click on the Log link under the Management menu. The Log page displays a list of events that are triggered on the Ethernet and Wireless interface. This log can be referred when an unknown error occurs on the system or when a report needs to be sent to the technical support department for debugging purposes. Syslog Select Enable or Disable Syslog function from the drop down list. Log Server IP Address Specify the Log Server IP address.
8.8 Management → Diagnostics Click on the Diagnostics link under the Management menu. This function allows you to detect connection quality and trace the routing table to the target. Traceroute can help you to manage your network by detecting any routing during the transmission. If any routers refuse to reply ICMP packet, the result will show * sign for its Domain Name or IP Address. Target IP Specify the IP address you would like to search. Ping Packet Size Specify the packet size of each ping.
9 Network Configuration Example This chapter describes the role of the M5000 with 4 different modes. The Access Point mode’s default configuration is a central unit of the wireless network or as a root device of the wired environment. 9.1 Access Point Access Point Step1 Login to the web-based configuration interface with default IP 192.168.1.1 Step2 Select your country or region’s regulation. Step3 802.11a wireless network Step4 Use site survey to scan channels that have been used in nearby area.
Auction: M5000’s Access Point Mode does not provide DHCP server so the Wireless Client IP address must configure manually at the same subnet in Local Area Network. 9.2 Client Bridge Mode Client Bridge Mode functions like a wireless dongle. It must connect to an Access Point/AP Router to join the network. Please refer to the last section to check Access point’s configuration. Client Bridge Step1 Login to the web-based configuration interface with default IP 192.168.1.
WDS Bridge Step1 Login to the web-based configuration interface with default IP 192.168.1.1 Step2 Select your country or region’s regulation. Step3 Select Operation Mode to WDS Bridge from System Properties. Step4 802.11a wireless network. Step5 Select channel you would like to use. Step6 Setup the authentication settings Step7 Setup WDS Link Settings. Step8 Specify the AP’s MAC address you would like to connect with. Step9 Press Apply to process all the configurations.
Please refer to the last section to check Access point’s configuration. Client Router Step1 Login to the web-based configuration interface with default IP 192.168.1.1 Step2 Select your country or region’s regulation. Step3 Select Operation Mode to Client Router from System Properties. Step4 Change your Local Area Network setting to Obtain an IP Address Automatically. Step5 802.11a wireless network. Step6 Use site survey to scan Access Points that are available in nearby area.
Mesh Step1 Login to the web-based configuration interface with default IP 192.168.1.1 Step2 Select your country or region’s regulation. Step3 Change device mode to Mesh from System Properties. Step4 Select wireless mode you would like to associate with. Step5 Select channel/frequency you would like to associate with. Step6 Specify SSID for the Mesh Network. Step7 Setup the authentication settings. Step8 Specify current device is a gateway or relay. Step9 Press Apply to save all changes.
Network. Once a Gateway is connected to a WISP, all wireless clients and Mesh can retrieve IP address automatically.
10 VLAN CONFIGURATION GUIDE Following procedures are used to configure VLAN on EnGenius product. EnGenius product supports both wireless and wired tagging on your network. Wireless tagging can help you to divide the permission for different group of users. Wireless Clients associated with SSID1-4 will not have the authority to manage the device when you enable the Profile Isolation except the Wireless VLAN ID is the same as Management VLAN ID.
2. Press “Wireless Network” to configure Wireless VLAN. 3. To configure Wireless VLAN Tagging, please press Edit at Wireless Network section.
4. After Press Edit, web should pop-out a window as below. You may enter your desire VLAN ID. Then, press Save to save the changes. 5. Wireless Network webpage should have display all the VID as below. If you would like to enable Wireless VLAN function, select the radio button of “Isolate all Profiles from each other using VLAN standard” and then press Apply to configure the changes.
6. Press Management VLAN to configure wired VID. Enter your desire VLAN ID and press Apply to configure the changes. Auction: After press Apply, you must configure your Layer2 Switch or RADIUS Server with the same VLAN ID. Otherwise, you cannot access to the device’s web-base configuration page. 7. For 802.1x authentication, you may construct your network as below diagram. Note: EnGenius product supports maximum 4 different SSID with different VLAN ID.
Appendix A – FCC Interference Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
