WIRELESS 11N LONG RANGE OUTDOOR CB/AP ENS200 User Guide V1.
TABLE OF CONTENTS TABLE OF CONTENTS Conventions Copyright 0-vi 0-viii Product Overview Package Contents 1-1 Product Overview 1-2 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3 Technical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS Installing the Device 2-2 Pre-Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2 Installing the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2 Web Configuration Logging In 3-1 Best Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS Configuring IP Settings 4-10 Configuring Spanning Tree Settings 4-11 Router Setup 4-12 Configuring WAN Settings 4-12 Static IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Dynamic IP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Point-to-Point Protocol over Ethernet (PPPoE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31 Wi-Fi Protected Access 2 Pre-Shared Key (WPA2-PSK). . . . . . . . . . . . . . . . . . . . . . . . . . 4-32 Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) Mixed . . . . . . . . . . . . . . . . . . . . . . . 4-33 Wi-Fi Protected Access (WPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34 Wi-Fi Protected Access 2 (WPA2) . . . . . . . . . .
TABLE OF CONTENTS Configuring Logging 4-50 Configuring Diagnostics 4-51 Viewing Device Discovery 4-52 Configure Denial of Service Protection 4-53 Logging Out 4-54 Appendix A Federal Communication Commission Interference Statement A-1 Appendix B Industry Canada Statement B-1 Appendix C WorldWide Technical Support C-1 V
CONVENTIONS Conventions The following conventions are used to give the user additional information about specific procedures or content. It is important to pay attention to these conventions as they provide information to prevent damage to equipment or personal injury. Example: Indicates information used to demonstrate or explain an associated concept. N/A: General Conventions Indicates that a component or a procedure is not applicable to this model.
CONVENTIONS Typographical Conventions The following typographical conventions are used in this document: Italics Indicates book titles, directory names, file names, path names, and program/process names. Constant width Indicates computer output shown on a computer screen, including menus, prompts, responses to input, and error messages. Constant width bold Indicates commands lines as entered on the computer. Variables contained within user input are shown in angle brackets (< >).
COPYRIGHT Copyright This user guide and its content is copyright of © EnGenius Networks, 2011. All rights reserved. Any redistribution or reproduction in part or in whole in any form is prohibited. Do not distribute, transmit, store in any form of electronic retrieval system or commercially exploit the content without the expressed written permission of EnGenius Networks.
Product Overview Chapter 1
PRODUCT OVERVIEW PACKAGE CONTENTS 1.1 Package Contents ITEM QUANTITY ENS200 Wireless Access Point / Client Bridge 1 PoE Injector (EPE1212) 1 24V/0.
PRODUCT OVERVIEW PRODUCT OVERVIEW 1.2 Product Overview Thank you for choosing ENS200. The ENS200 is a long range, high performance IEEE 802.11b/g/n network solution that provides Access Point, Client Bridge, WDS, and Client Router functions in a single device. In addition to providing the latest wireless technology, the ENS200 supports Power over Ethernet and Power by Adapter capabilities, which allow the device to be installed easily in nearly any indoor or outdoor location.
PRODUCT OVERVIEW BENEFITS Benefits Wireless extensions to Ethernet networks WLANs enable network managers in dynamic environments to minimize overhead caused by moves, extensions to networks, and other changes. The ENS200 is the ideal product around which you can build your WLAN.
PRODUCT OVERVIEW TECHNICAL SPECIFICATION Technical Specification Wireless Specification IEEE802.11b/g/n, 1T1R, 150Mbps 2.400 to 2.484 GHz, programmable upon different country regulations Hardware Specification Physical Interface: 2 x 10/100Mbps LAN Ports, 1 x Reset Button Power Supply: Passive PoE, 24V/0.
PRODUCT OVERVIEW PRODUCT LAYOUT 1.3 Product Layout BACK PANEL VIEW A B C A B C Power LED Figure 1-1: Back Panel View 1-5 OFF = ENS200 is not receiving power ON = ENS200 is receiving power LAN (2) LEDs OFF = ENS200 is not connected to the network.
PRODUCT OVERVIEW PRODUCT LAYOUT A BOTTOM VIEW A Reset Button B LAN Connector C PoE LAN Connector B C DESCRIPTION To reset to factory settings, press button for > 10 seconds. To configure the ENS200, connect to an Ethernet adapter in a computer.
Installation Chapter 2
INSTALLATION SYSTEM REQUIREMENTS 2.1 System Requirements To install the ENS200, you need the following: Computer (Windows, Linux, Mac OS X Operating System) Web Browser (Internet Explorer, FireFox, Chrome, Safari) Network Interface Card with an open RJ-45 Ethernet Port Wi-Fi Card or USB Wi-Fi Dongle (802.
INSTALLATION INSTALLING THE DEVICE 2.2 Installing the Device Installing the Device Installing the ENS200 on a pole or wall optimizes the wireless access range. To install the ENS200, use the following procedure to mount the device on a pole and refer to the figure below. Note: Only experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities should install the ENS200. 1.
INSTALLATION INSTALLING THE DEVICE 5. Plug the other end of the Ethernet cable into the PoE port of the PoE injector. PoE LAN Figure 2-1: Installing the ENS200 6. Turn over the ENS200. Then insert the mast strap through the middle hole of the ENS200. Use a screwdriver to unlock the pole-mounting ring putting it through the ENS200. 7. Mount the ENS200 securely to the pole by locking the strap tightly. This completes the installation procedure.
Web Configuration Chapter 3
WEB CONFIGURATION LOGGING IN 3.1 Logging In The ENS200 has a built-in Web Configurator that lets you manage the unit from any location using a Web browser that supports HTTP and has Javascript installed. 3. When the login screen appears, enter admin for the username in the top field and admin for the password in the bottom field. After configuring the computer for TCP/IP using the procedure appropriate for your operating system, use that computer’s Web browser to log in to the ENS200 Web Configurator.
WEB CONFIGURATION BEST PRACTICES Best Practices Perform the following procedures regularly to make the ENS200 more secure and manage the ENS200 more effectively. Change the default password Use a password that is not easy to guess and that contains different characters, such as numbers and letters. The ENS200 username cannot be changed. For more information, see Configuring Administrator Account. Back up the configuration and be sure you know how to restore it.
Basic Network Settings Chapter 4
BASIC NETWORK SETTINGS SYSTEM STATUS 4.1 System Status View the summary of the current system status including system (hardware/software version, date/time), wired network (LAN) and wireless network (WLAN) information. 4.1.1 Using Save/Reload Save and apply the settings shown in the Unsaved changes list, or cancel the unsaved changes and revert to the previous settings that were in effect.
BASIC NETWORK SETTINGS VIEWING SYSTEM INFORMATION 4.1.2 Viewing System Information Displays status information about the current operating mode. System Information shows the general system information such as operating mode, system up time, firmware version, serial number, kernel version, and application version. LAN Settings shows Local Area Network settings such as the LAN IP address, subnet mask, and MAC address.
BASIC NETWORK SETTINGS VIEWING SYSTEM INFORMATION Current Wireless Settings shows wireless information such as frequency and channel. Since the ENS200 supports multipleSSIDs, information about each SSID, such as its ESSID and security settings, are displayed.
BASIC NETWORK SETTINGS VIEWING WIRELESS CLIENT LIST 4.1.3 Viewing Wireless Client List Displays a list of clients associated to the ENS200, along with the MAC addresses and signal strength for each client. Click the Refresh button to update the client list.
BASIC NETWORK SETTINGS VIEWING SYSTEM LOG 4.1.4 Viewing System Log The ENS200 automatically logs events to internal memory. Note: The oldest events are deleted from the log when memory is full. Click the Refresh button to update the client list or the Clear button to remove all events.
BASIC NETWORK SETTINGS VIEWING CONNECTION STATUS 4.1.5 Viewing Connection Status Displays the current status of the network. The WLAN information shown includes network type, SSID, BSSID, connection status, wireless mode, current channel, security, data rate, noise level, and signal strength. The WAN information shown includes the MAC address, connection type, connection status, IP address, IP subnet mask, primary DNS and secondary DNS.
BASIC NETWORK SETTINGS VIEWING DHCP CLIENT TABLE 4.1.6 Viewing DHCP Client Table Displays the clients that are associated to the ENS200 through DHCP. The MAC addresses and signal strength for each client are also shown. Click the Refresh button to update the client list.
BASIC NETWORK SETTINGS VIEWING WDS LINK LIST 4.1.7 Viewing WDS Link List Displays the clients that are associated to the ENS200 through WDS. The MAC addresses, link status and signal strength for each client are also shown. Click the Refresh button to update the client list.
BASIC NETWORK SETTINGS SYSTEM SETUP 4.2 System Setup The following sections explain the features and functionality of the ENS200 in access point mode, client bridge mode, WDS access point mode, WDS bridge mode, WDS station mode and client router mode. 4.2.1 Configuring Operation Mode Set the primary function of the device. The function that is selected affects which items are available in the main menu. Device Name Enter a name for the device. The name you type appears in SNMP management.
BASIC NETWORK SETTINGS CONFIGURING IP SETTINGS 4.2.2 Configuring IP Settings Configure the LAN settings for the ENS200 using a static or dynamic IP address. IP Network Setting Configure the network connection type using either a static IP or dynamic IP. IP Address Enter the LAN IP address of the ENS200. Subnet Mask Enter the subnet mask of the ENS200. Default Gateway Enter the default gateway of the ENS200. Primary DNS Enter the primary DNS address of the ENS200.
BASIC NETWORK SETTINGS CONFIGURING SPANNING TREE SETTINGS 4.2.3 Configuring Spanning Tree Settings Spanning Tree Status Enable or disable the ENS200 Spanning Tree function. Bridge Hello Time Specify Bridge Hello Time, in seconds. This value determines how often the ENS200 sends hello packets to communicate information about the topology throughout the entire Bridged Local Area Network Bridge Max Age Specify Bridge Max Age, in seconds.
BASIC NETWORK SETTINGS ROUTER SETUP 4.3 Router Setup 4.3.1 Configuring WAN Settings Configure the WAN settings for the ENS200 using a static or dynamic IP address, PPPoE or PPTP. Static IP Setting a static IP address allows an administrator to set a specific IP address for the router and guarantees that it can not be assigned a different address. Account Name Enter the account name provided by your ISP. Domain Name Enter the domain name provided by your ISP.
BASIC NETWORK SETTINGS DYNAMIC IP Secondary DNS Enter the secondary DNS server address. Discard Ping on WAN Check to Enable to recognize pings on the ENS200 WAN interface or Disable to block pings on the ENS200 WAN interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is valid. Blocking pings provides some extra security from hackers. Click Accept to save the settings or Cancel to discard changes.
BASIC NETWORK SETTINGS POINT-TO-POINT PROTOCOL OVER ETHERNET (PPPOE) Point-to-Point Protocol over Ethernet (PPPoE) Point-to-Point Protocol over Ethernet (PPPoE) is used mainly by ISPs that provide DSL modems to connect to the Internet. MTU Enter the maximum transmission unit (MTU). The MTU specifies the largest packet size permitted for an internet transmission (PPPoE default: 1492). The MTU size can be set between 512 and 1492. Login Enter the username assigned by an ISP.
BASIC NETWORK SETTINGS POINT-TO-POINT TUNNELLING PROTOCOL (PPTP) Point-to-Point Tunnelling Protocol (PPTP) The point-to-point tunnelling protocol (PPTP) is used in association with virtual private networks (VPNs). There a two parts to a PPTP connection: the WAN interface settings and the PPTP settings. MTU Enter the maximum transmission unit (MTU). The MTU specifies the largest packet size permitted for an internet transmission (PPPoE default: 1492). The MTU size can be set between 512 and 1492.
BASIC NETWORK SETTINGS POINT-TO-POINT TUNNELLING PROTOCOL (PPTP) Use These DNS Servers Click the radio button to set up the Primary DNS and Secondary DNS servers manually. Discard Ping on WAN Check to Enable to recognize pings on the ENS200 WAN interface or Disable to block pings on the ENS200 WAN interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is valid. Blocking pings provides some extra security from hackers.
BASIC NETWORK SETTINGS CONFIGURING LAN SETTINGS 4.3.2 Configuring LAN Settings IP Address Enter the LAN port IP address. IP Subnet Mask Enter the LAN IP subnet mask. WINS Server IP Enter the WINS Server IP. Use Router As DHCP Server Check this option to enable the ENS200 internal DHCP server. Starting IP Address Specify the starting IP address range for the pool of allocated for private IP addresses.
BASIC NETWORK SETTINGS CONFIGURING VPN PASS-THROUGH 4.3.3 Configuring VPN Pass-Through VPN Pass-through allows a secure virtual private network (VPN) connection between two computers. Enabling the options on this page opens a VPN port and enables connections to pass through the ENS200 without interruption. PPTP Pass-through Check this option to enable PPTP pass-through mode. L2TP Pass-through Check this option to enable L2TP pass-through mode.
BASIC NETWORK SETTINGS CONFIGURING PORT FORWARDING 4.3.4 Configuring Port Forwarding Port forwarding enables multiple server applications on a LAN to serve clients on a WAN over a single WAN IP address. The router accepts incoming client packets, filters them based on the destination WAN, or public, port and protocol and forwards the packets to the appropriate LAN, or local, port. Unlike the DMZ feature, port forwarding protects LAN devices behind the firewall. NO.
BASIC NETWORK SETTINGS CONFIGURING PORT FORWARDING Service Name Enter a name for the port forwarding rule. Protocol Select a protocol for the application: Choices are Both, TCP, and UDP. Starting Port Enter a starting port number. Ending Port Enter an ending port number. All ports numbers between the starting and ending ports will forward users to the IP address specified in the IP Address field. IP Address Enter the IP address of the server computer on the LAN network where users will be redirected.
BASIC NETWORK SETTINGS CONFIGURING DEMILITARIZED ZONE 4.3.5 Configuring Demilitarized Zone Configuring a device on the LAN as a demilitarized zone (DMZ) host allows unrestricted two-way Internet access for Internet applications, such as online video games, to run from behind the NAT firewall. The DMZ function allows the router to redirect all packets going to the WAN port IP address to a particular IP address on the LAN.
BASIC NETWORK SETTINGS CONFIGURING WIRELESS LAN 4.4 Configuring Wireless LAN 4.4.1 Configuring Wireless Settings Instructions on how to configure the wireless and security settings for each of the possible operating modes. ! WARNING! Incorrectly changing these settings may cause the device to stop functioning. Do not modify the settings in this section without a thorough understanding of the parameters. Access Point Mode The ENS200 supports Access Point Mode.
BASIC NETWORK SETTINGS ACCESS POINT MODE AP Detection AP Detection can select the best channel to use by scanning nearby areas for Access Points. Current Profile Configure up to four different SSIDs. If many client devices will be accessing the network, you can arrange the devices into SSID groups. Click Edit to configure the profile and check whether you want to enable extra SSIDs. Click Accept to confirm the changes or Cancel to cancel and return previous settings.
BASIC NETWORK SETTINGS CLIENT BRIDGE MODE Client Bridge Mode Client Bridge Mode lets you connect two LAN segments via a wireless link as though they are on the same physical network. Since the computers are on the same subnet, broadcasts reach all machines. As a result, DHCP information generated by the server reach all client computers as though the clients residing on one physical network. Wireless Mode Wireless mode supports 802.11b/ g/n mixed modes. SSID Specify the SSID if known.
BASIC NETWORK SETTINGS CLIENT BRIDGE MODE Profile If you used the Site Survey, the Web Configurator shows nearby Access Points. To connect to an Access Point, click the Access Point’s BSSID. Wireless Security See Configuring Wireless Security. Click Refresh to scan again.
BASIC NETWORK SETTINGS WDS BRIDGE MODE WDS Bridge Mode Unlike traditional bridging. WDS Bridge Mode allows you to create large wireless networks by linking several wireless access points with WDS links. WDS is normally used in large, open areas, where pulling wires is cost prohibitive, restricted or physically impossible. Wireless Mode Wireless mode supports 802.11b/g/n mixed modes. Channel HT Mode The default channel bandwidth is 40 MHz.
BASIC NETWORK SETTINGS WDS BRIDGE MODE Security Select the type of WDS security: None, WEP, or AES. WEP Key Enter the WEP key. AES Pass phrase Enter the AES pass phrase. MAC Address Enter the MAC address of the Access Point to which you want to extend wireless connectivity. Mode Select Disable or Enable to disable or enable WDS. Click Accept to confirm the changes or Cancel to cancel and return previous settings.
BASIC NETWORK SETTINGS CLIENT ROUTER MODE Client Router Mode In Client Router Mode, you can access the Internet wirelessly with the support of a WISP. In AP Router Mode, the ENS200 can access the Internet via a cable or DSL modem. In this mode, the ENS200 can be configured to turn off the wireless network name (SSID) broadcast, so that only stations that have the SSID can be connected.
BASIC NETWORK SETTINGS CLIENT ROUTER MODE Profile If you used the Site Survey, the Web Configurator shows nearby Access Points. To connect to an Access Point, click the Access Point’s BSSID. Wireless Security See Configuring Wireless Security. Click Refresh to scan again.
BASIC NETWORK SETTINGS CONFIGURING WIRELESS SECURITY 4.4.2 Configuring Wireless Security The Wireless Security Settings section lets you configure the ENS200’s security modes: WEP, WPA-PSK, WPA2-PSK, WPA-PSK Mixed, WPA, WPA2, and WPA Mixed. We strongly recommend you use WPA2-PSK. Wired Equivalent Privacy (WEP) Security Mode Select WEP from the drop-down list to begin the configuration. Auth Type Select Open System or Shared. Input Type Select an input type of Hex or ASCII.
BASIC NETWORK SETTINGS WI-FI PROTECTED ACCESS PRE-SHARED KEY (WPA-PSK) Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) Security Mode Select WPA-PSK from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires passphrase. AES = automatic encryption with WPA2-PSK; requires passphrase. Passphrase Specify the security password.
BASIC NETWORK SETTINGS WI-FI PROTECTED ACCESS 2 PRE-SHARED KEY (WPA2-PSK) Wi-Fi Protected Access 2 Pre-Shared Key (WPA2-PSK) Security Mode Select WPA2-PSK from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires passphrase. AES = automatic encryption with WPA2-PSK; requires passphrase. Passphrase Specify the security password.
BASIC NETWORK SETTINGS WI-FI PROTECTED ACCESS PRE-SHARED KEY (WPA-PSK) MIXED Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) Mixed Security Mode Select WPA2-PSK Mixed from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires passphrase. AES = automatic encryption with WPA2-PSK; requires passphrase. Passphrase Specify the security password.
BASIC NETWORK SETTINGS WI-FI PROTECTED ACCESS (WPA) Wi-Fi Protected Access (WPA) Security Mode Select WPA from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires passphrase. AES = automatic encryption with WPA2-PSK; requires passphrase. Radius Server Specify the IP address of the RADIUS server.
BASIC NETWORK SETTINGS WI-FI PROTECTED ACCESS 2 (WPA2) Wi-Fi Protected Access 2 (WPA2) Security Mode Select WPA2 from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires passphrase. AES = automatic encryption with WPA2-PSK; requires passphrase. Radius Server Specify the IP address of the RADIUS server.
BASIC NETWORK SETTINGS WI-FI PROTECTED ACCESS (WPA) MIXED Wi-Fi Protected Access (WPA) Mixed Security Mode Select WPA Mixed from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires passphrase. AES = automatic encryption with WPA2-PSK; requires passphrase. Radius Server Specify the IP address of the RADIUS server.
BASIC NETWORK SETTINGS CONFIGURING WIRELESS MAC FILTER 4.4.3 Configuring Wireless MAC Filter Note: This section applies to Access Point and WDS Access point mode. Wireless MAC Filters are used to allow or deny network access to wireless clients according to their MAC addresses. You can manually add a MAC address to restrict the permission to access ENS200. The default setting is Disable Wireless MAC Filters.
BASIC NETWORK SETTINGS CONFIGURING WDS LINK SETTINGS 4.4.4 Configuring WDS Link Settings Using WDS Link Settings, you can create a wireless backbone link between multiple access points that are part of the same wireless network. This allows a wireless network to be expanded using multiple Access Points without the need for a wired backbone to link them, as is traditionally required. Security Select the type of WDS security: None, WEP, or AES. WEP Key Enter the WEP key.
BASIC NETWORK SETTINGS CONFIGURING ADVANCED NETWORK SETTINGS 4.4.5 Configuring Advanced Network Settings Network address translation (NAT) allows users on the LAN to access the Internet through a single or multiple Public IP Addresses. NAT provides firewall protection from hacker attacks and allows for mapping LAN IP addresses to WAN IP addresses with key services such as websites, FTP, video game servers, etc. Data Rate Select a data rate from the drop-down list. The data rate affects throughput.
BASIC NETWORK SETTINGS MANAGEMENT SETUP 4.5 Management Setup The Management section lets you configure administration, management VLAN, SNMP settings, backup/restore settings, firmware upgrade, time settings, and log settings. This chapter describes these settings. 4.5.1 Configuring Administrator Account Click the Administration link under the Management menu to change the user name and password used to log on to the ENS200 Web Configurator.
BASIC NETWORK SETTINGS CONFIGURING MANAGEMENT VLAN 4.5.2 Configuring Management VLAN Click the Management VLAN link under the Management menu to assign a VLAN tag to the packets. A VLAN is a group of computers on a network whose software has been configured so that they behave as if they were on a separate Local Area Network (LAN).
BASIC NETWORK SETTINGS CONFIGURING SNMP 4.5.3 Configuring SNMP SNMP is used in network management systems to monitor network-attached devices for conditions that warrant administrative attention. SNMP Enable or disable the ENS200 SNMP function. Contact Enter the contact details of the device. Location Enter the location of the device. Community Name (Read Only) Enter the password for accessing the SNMP community for read-only access.
BASIC NETWORK SETTINGS CONFIGURING SNMP Engine ID Specify the engine ID for SNMPv3. Click Save/Apply to apply the changes or Cancel to return previous settings.
BASIC NETWORK SETTINGS CONFIGURING BACKUP/RESTORE SETTINGS 4.5.4 Configuring Backup/Restore Settings Click the Backup/Restore Setting link under the Management menu to save the ENS200’s current settings in a file on your local disk or load settings onto the device from a local disk. This feature is particularly convenient administrators who have several ENS200 devices that need to be configured with the same settings. This page also lets you return the ENS200 to its factory default settings.
BASIC NETWORK SETTINGS CONFIGURING FIRMWARE UPGRADE 4.5.5 Configuring Firmware Upgrade Firmware is system software that operates and allows the administrator to interact with the router. ! WARNING! Upgrading firmware through a wireless connection is not recommended. Firmware upgrading must be performed while connected to an Ethernet (LAN port) with all other clients disconnected. The firmware upgrade procedure can take several minutes.
BASIC NETWORK SETTINGS CONFIGURING SYSTEM TIME 4.5.6 Configuring System Time Change the system time of the ENS200 by manually entering the information, synchronizing the device with a PC, or setup automatic updates through a network time (NTP) protocol server. Manually Set Date and Time Enter the date and time values in the date and time fields or click the Synchronize with PC button to get the date and time values from the administrator’s PC.
BASIC NETWORK SETTINGS CONFIGURING WI-FI SCHEDULE 4.5.7 Configuring Wi-Fi Schedule Use the Wi-Fi schedule function to control the wireless power ON/OFF service that operates on a routine basis. Add a Schedule Service Create a schedule service type and date/time parameters for a specific service. Schedule Name Enter the description of the schedule service. Service Select the type of schedule service, either Wireless Power ON or Wireless Power OFF.
BASIC NETWORK SETTINGS SCHEDULE SERVICES TABLE Schedule Services Table The Schedule function relies on the GMT time setting acquired from a network time protocol (NTP) server. For details on how to connect the ENS200 to an NTP server, see Configuring System Time. Schedule Table Displays a list of scheduled services for the ENS200. The properties of each service displayed are: # Displays the ID number of the service in the table. Name Displays the description of the service.
BASIC NETWORK SETTINGS CONFIGURING COMMAND LINE INTERFACE 4.5.8 Configuring Command Line Interface Most users will configure the ENS200 through the graphical user interface (GUI). However, for those who prefer an alternative method there is the command line interface (CLI). The CLI can be access through a command console, modem or Telnet connection. CLI Select to enable or disable the ability to modify the ENS200 via a command line interface (CLI).
BASIC NETWORK SETTINGS CONFIGURING LOGGING 4.5.9 Configuring Logging Display a list of events that are triggered on the ENS200 Ethernet and wireless interfaces. You can consult this log if an unknown error occurs on the system or when a report needs to be sent to the technical support department for debugging purposes. Syslog Enable or disable the ENS200 syslog function. Log Server IP Address Enter the IP address of the log server. Local Log Enable or disable the local log service.
BASIC NETWORK SETTINGS CONFIGURING DIAGNOSTICS 4.5.10 Configuring Diagnostics The diagnosis feature allow the administrator to verify that another device is available on the network and is accepting request packets. If the ping result returns alive, it means a device is on line. This feature does not work if the target device is behind a firewall or has security software installed. Target IP / Domain Name Enter the IP address you would like to search. Ping Packet Size Enter the packet size of each ping.
BASIC NETWORK SETTINGS VIEWING DEVICE DISCOVERY 4.5.11 Viewing Device Discovery Device Name Displays the name of the devices connected to the network. Operation Mode Displays the operation mode of the devices connected to the network. IP Address Displays the IP address of the devices connected to the network. System MAC Address Displays the system MAC address of the devices connected to the network. Firmware Version Displays the firmware version of the devices connected to the network.
BASIC NETWORK SETTINGS CONFIGURE DENIAL OF SERVICE PROTECTION 4.5.12 Configure Denial of Service Protection Use TCP SYN Cookies Protection Click to enable TCP SYN cookies protection. SYN Flood Attack Protection Click to enable or disable SYN Flood Attack Protection. Match Interval Per Second Enter the allowed number of packets per second. Limit Packets Enter the maximum number of packets allowed per request. UDP Flood Attack Protection Click to enable or disable UDP Flood Attack Protection.
BASIC NETWORK SETTINGS LOGGING OUT 4.5.13 Logging Out Click Logout to logout from the ENS200.
APPENDIX A FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT Appendix A Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
APPENDIX A FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT Important: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with FCC RF Exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
APPENDIX B INDUSTRY CANADA STATEMENT Appendix B Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
APPENDIX C WORLDWIDE TECHNICAL SUPPORT Appendix C WorldWide Technical Support REGION/COUNTRY OF PURCHASE SERVICE CENTRE SERVICE INFORMATION CANADA Canada LOS ANGELES, USA USA C-1 web site www.engeniuscanada.com email rma@engeniuscanada.com contact numbers Toll Free: (+1) 888-397-2788 Local: (+1) 905-940-8181 hours of operation Monday - Friday 9:00AM to 5:30PM EST (GMT-5) web site www.engeniustech.com email support@engeniustech.
APPENDIX C WORLDWIDE TECHNICAL SUPPORT REGION/COUNTRY OF PURCHASE SERVICE CENTRE SERVICE INFORMATION MIAMI, USA Mexico, Central and Southern America NETHERLANDS Europe Africa Middle East Russia CIS / Armenia, Azerbaijan, Belarus, Georgia, Kazakhstan, Kyrgyzstan, Moldova, Tajikistan, Turkmenistan, Ukraine, Uzbekistan Turkey Afghanistan Pakistan Bangladesh, Maldives, Nepal, Bhutan, Sri Lanka DUBAI, UAE C-2 web site [ES] es.engeniustech.com [PT] pg.engeniustech.
APPENDIX C WORLDWIDE TECHNICAL SUPPORT REGION/COUNTRY OF PURCHASE Singapore, Cambodia, Indonesia, Malaysia, Thailand, Philippines, Vietnam China, Hong Kong, Korea India South Africa Oceania Others SERVICE CENTRE SERVICE INFORMATION SINGAPORE TAIWAN, R.O.C. Note: * Service hours are based on the local time of the service center. * Please visit the website for the latest information about customer service. C-3 web site www.engeniustech.com.sg/e_warranty_form email techsupport@engeniustech.com.
