Specifications
ENFORCER Wireless Help Button
2 SECO-LARM U.S.A., Inc.
2x
Wall
plate screws
2x
Mounting screws
2x
Wall anchors
1x
9V Alkaline battery
4
x
Adhesive
rubber
feet
1x
Manual
Specifications:
Overview:
Dimensions:
Introduction:
The ENFORCER Wireless Help Button can be used to wirelessly expand the Room Monitor
(RM-R100-KB1Q) with a service/help button. The button is perfect for placing on a desktop, mounting on
walls, or any other location where it is difficult to run wires. The Wireless Help Button combines the very
best of SECO-LARM, flexible wireless solutions and reliable access control.
Parts List:
1x Wireless Help Button 1x Back box
Operating frequency 433.92MHz
Operating voltage 9VDC
Maximum range 250' (76m)*
Battery life Up to four (4) years (60 uses per day)
Dimensions
Desktop 4
5
/
8
"x2
7
/
8
"x1
7
/
8
" (117x73x48 mm)
Wall mount
4
5
/
8
"x2
7
/
8
"
x2
"
(117x73x50 mm)
Weight 6-oz (178g)
*Actual operating range will vary greatly depending on the installation and operating environment.
Desktop Wall mount
4
5
/
8
"
(117mm)
2
7
/
8
"
(73mm)
2"
(50mm)
15
/
16
"
(24mm)
4
5
/
8
"
(117mm)
1
7
/
16
"
(36mm)
1
7
/
8
"
(48mm)
Battery clip
9V Alkaline
battery
Request
button
LED Indicator
Off: No transmission
Blue: Transmitting
Red: Low battery
Push
for Help
Push
for Help
1
3
/
4
"
(45mm)
ENFORCER Wireless Help Button
SECO-LARM U.S.A., Inc. 3
Installation:
RM
-
R100
-
TB
Q
Sample Application
s
:
You can easily print your own message plate on very thin card stock, no
thicker than the included message plate, and trim to 1
7
/
8
" (37mm) square.
NOTE: Thicker card stock will not allow the transparent lens to fully seat.
1. Use the tip of a very thin screwdriver to pry off the transparent lens
over the message plate (see Fig. 1).
2. Replace the current plate with the desired message plate, keeping the
spacer plate in place.
3. Check that message plate orientation is correct.
4. Carefully snap the lens assembly back on.
Fig. 1
Your
Custom
Message
Message
Plate
Transparent
lens
Changing the Message Plate
:
Spacer
Plate
1. Find a suitable location for the Wireless Help Button.
NOTE: Do not house in a metal box as this will greatly reduce the range.
2. The Wireless Help Button can either be wall mounted (taller side of back box on bottom), or placed
on a desktop (taller side of back box on top).
3. Test the operation of the Wireless Help Button in the location where it will be installed before
finalizing the installation.
NOTE: The Wireless Help Button needs to be programmed into the RM-R100-RB1Q or a
SK-910 (433.92MHz) series receiver before testing. See the receiver manual for transmitter
learning procedure.
4. Ensure the battery clip is securely connected, mount the Wireless Help Button in the back box
according to the appropriate orientation stated above, and secure it with the two included screws. Apply
the included adhesive rubber feet for desktop applications.
Indicator/Receiver
RM-R100-RB1Q
1
2
Wireless Help Button
RM-R100-TBQ
Sensor/Transmitter
RM-R100-TLQ
Basic Installation with Room Monitor Kit (RM-R100-KB1Q)
Room occupied
–
i
ndicator/
r
eceiver LED is
lit.
Wireless pushbutton pressed – indicator/receiver
LED flashes and/or buzzer sounds
Attendant uses wireless remote (not included) to
reset the indicator flashing LED and/or buzzer.
Light/Buzzer
and
RF receiver
(not included)
Wireless Help Button
RM-R100-TBQ
Sensor/Transmitter
RM-R100-TLQ
Room occupied
Room occupied
–
remote i
ndicator/
r
eceiver LED is
lit
.
Wireless pushbutton pressed – light/buzzer connected to a
433.92MHz RF receiver outside door is triggered and remote
indicator/receiver LED flashes and/or buzzer sounds
Attendant uses wireless pushbutton (or wireless remote, not
included) to reset the Indicator flashing LED and/or buzzer.
Indicator/Receiver
RM-R100-RB1Q