Specifications

ManualsBrandsENFORCER ManualsHome building and DecorDP-236Q

DP-236Q

• Wireless operation – camera and monitor can

operate from up to 492ft (150m)

away

• Camera has built-in IR LEDs for nighttime

operation

• Remotely and securely talk to visitors and

unlock doors or gates via the monitor

• Lightweight monitor can be carried around the

premises while talking to the visitor

• Connect up to two additional monitors

• Camera includes a built-in PIR sensor that

activates the camera and takes photos of the

visitor when he or she approaches

• Monitor includes a kickstand and a charging

base

• Camera powered by 9~16 VAC/5~16 VDC

• Monitor front door at any time

• Egress input

• 120° wide viewing angle

Second and third monitors sold separately.

Line-of-sight range. Actual range may vary depending on the installation and operating environment.

Manual

Wireless Video Door Phone

Summary of content (12 pages)

PAGE 1
DP-236Q Wireless Video Door Phone Manual 3 • • • • • Wireless operation – camera and monitor can operate from up to 492ft (150m)2 away Camera has built-in IR LEDs for nighttime operation Remotely and securely talk to visitors and unlock doors or gates via the monitor Lightweight monitor can be carried around the premises while talking to the visitor Connect up to two additional monitors1 1Second • • • • • • Camera includes a built-in PIR sensor that activates the camera and takes photos of the visit
PAGE 2
ENFORCER Wireless Video Door Phone Table of Contents: Introduction ....................................................... 2 Parts List ........................................................... 2 Also Available ................................................... 2 Specifications .................................................... 3 Overview ........................................................... 3 Display Overview .............................................. 4 Installation Notes ..................
PAGE 3
ENFORCER Wireless Video Door Phone Specifications: Type Chip Resolution Lens Viewing angle Operating voltage Relock delay Relay output Active Current draw Standby Active Battery life Standby PIR Detection range PIR Detection angle Dimensions Weight Operating temperature Camera Color Camera CMOS 480 TV Lines 2mm 120° 9~16 VAC/5~16 VDC 1~6 s 3A@250VAC/30VDC 250mA@4.2VDC 3mA@4.2VDC 4.4 Hours 366 Hours (15 days) 9’ (3m) 138° 511/16”x31/8”x23/8” (144x80x60 mm) with bracket 4.
PAGE 4
ENFORCER Wireless Video Door Phone Display Overview: : Signal Strength – Displays the wireless signal strength : Time – Displays the current time : PIR – Displays when the PIR sensor is turned on : Ringer – Displays if the ringer is audible or muted : Missed Call – Displays when there is a missed call : Two-Way Communication – Displays when the monitor and camera station can hear each other : Relay – Displays while the relay is active : Camera Battery: Displays the current camera station battery level : M
PAGE 5
ENFORCER Wireless Video Door Phone 6 5 N.C. Output 4 N.O. Output Egress input (N.O., -) 1 COM 2 3 Camera Wiring Diagram: (–) 9~16 VAC/ (+) 5~16 VDC 1) Positive (+) power input. Connect to the red wire of the included AC adapter or to the positive wire of the doorbell’s power supply. 2) Negative (-) power input. Connect to the black wire of the included AC adapter or to the negative wire of the doorbell’s power supply. 3) Egress (N.O.) negative input. Connect to an optional N.O. egress device.
PAGE 6
ENFORCER Wireless Video Door Phone Installation – Camera: 1. Position the camera so the area to be monitored is easily visible, optimally 5ft (1.5m) above the ground. Do not position the camera in direct sunlight, or where it will be exposed directly to rain or snow. NOTE: For best results, the visitor should stand 2.5~5ft (0.8~1.5m) away from camera. 2. Cut a hole large enough to run the min. 21AWG 2-conductor wire to the door unlock device through the wall, as well as to the included power supply. 3.
PAGE 7
ENFORCER Wireless Video Door Phone Installation – Monitor (continued): Recharge the monitor battery: There are two ways to recharge the monitor battery. 1. Place the monitor into the monitor charger stand and plug the charger into the stand. 2. Plug the charger directly into the monitor. Turn monitor ON: Hold the “ON/OFF” button for 3 seconds. The monitor will turn ON with the ENFORCER screen.
PAGE 8
ENFORCER Wireless Video Door Phone Programming: 1. While the monitor display is on, hold the “Photo/Settings” button for 3 seconds to enter programming mode. 2. Press the “Photo/Settings” button to cycle through the programming options, including: a. Time setup b. Ringtone choice c. Lock delay d. PIR setup 3. To exit programming mode, press the “Photo/Settings” button to cycle through the remaining programming modes, or press the “Talk” button to return to the home screen.
PAGE 9
ENFORCER Wireless Video Door Phone Operating the Wireless Video Door Phone: Request entry: 1. Press the doorbell button on the camera. 2. Wait for someone to press the “ON/OFF” button on the monitor to unlock the door. ON/OFF: • Turn monitor ON/OFF • Standby mode • Unlock door Talk Doorbell View Photo/ Settings Receive a visitor: 1. If a visitor presses the doorbell button on the camera, the monitor’s display turns ON and the monitor sounds the chosen ring tone. 2.
PAGE 10
ENFORCER Wireless Video Door Phone Operating the Wireless Video Door Phone (continued): Adjust the monitor’s color tint: 1. Press the “ON/OFF” button to turn the monitor’s display ON. 2. Press the monitor’s “View” button to turn the camera on. 3. While the camera’s image is displayed, press the up and down arrows on the front of the monitor to turn Arrow View the brightness up and down. Buttons 4. Press the monitor’s “View” button to save the brightness setting and turn the camera off.
PAGE 11
ENFORCER Wireless Video Door Phone Resetting the Camera and Pairing a First Monitor: To reset the camera and pair a first monitor: 1. Clear the camera’s existing pairings: a. Remove the camera from the bracket. b. The alarm will begin to sound. c. Remove the battery from the camera then replace the battery to deactivate the tamper alarm. d. Use a paper clip or other small object to press and hold the camera’s reset button for three seconds. A beep confirms the pairings have been cleared. 2.
PAGE 12
ENFORCER Wireless Video Door Phone Troubleshooting: The monitor’s screen is blank. • Make sure the “ON/OFF” button was pressed. • Recharge the monitor’s battery. • Plug the charger directly into the monitor. The monitor recharges when plugged • Check that the monitor is firmly seated in the charging directly in, but not in the recharging stand. stand, indicated by the cradle’s red charging light. The monitor’s screen turns on, but does not display the camera’s image.