Owner`s manual

PRODUCT INFORMATION
6External Roof-mounted Power Vent System EuropeanHome.com
3
3903001 05.12
 3 . MechanicalInstallation
3.1InstallationofProvenDraftSwitch(PDS1)
The PDS 1 is for indoor installation only. The PDS 1 must be installed in a vertical position with the pressure
  connectionpointingdown.Securetheswitchbyusingthemountingholesasshownonthegure.Afterinstallation
connect the tubing from the probe onto the port marked accessible through the small of the plastic enclosure.
Connect tubing to the NEGATIVE (-) port on the PDS.
Factory wiring comes with three wires that are already crimped onto the PDS. The purpose of these wires is to
provide a point in which you can extend the length of the wire by using wire nuts and additional wire (not provided).
3.2InstallationofStackProbeforPDS1
A stack probe is used with ENERVEX Proven Draft
Switches (PDS). The PDS 1 monitors the pressure
inside the stack and signals the control to shut down the
  applianceifinsufcientdraftexistsinsidethestack.The
probe must be installed between the appliance and
the exhaust fan.
For all installations, the stack probe must be placed
  s o theowthroughthestackisperpendiculartothetip
of the probe. Locate the probe at least the distance
“A” away from any elbows or tees in the stack.
  T h e distance“A”isdenedasatleast
  three(3)ventdiameters;A≥3*V(seegurebelow).To
prevent condensation from entering the probe or PDS
when installed on a horizontal stack, the probe
must be installed above the centerline of the stack. For
  replaceinstallations,thestackprobeshouldbe 
installed as close to the exhaust fan as possible.
ENERVEX
ENDURA PLASTICS
XP042105-1-1
REV A
0.05” WC PR
MOUNT DIAPHRAGM VERTICAL
UR
Mounting holes
Connection for
tubing at the bottom of
the enclosure
BRACKET ASM.
SELF TAPPING SCREWS
(RECOMMEND 1/4-20 OR M6)
(NOT PROVIDED
)
GASKET
PROBE
FERRULE
END CAP
ENERVEX®
View of PDS 1 with Cover Removed
3
3903001 05.12
 3 . MechanicalInstallation
3.1InstallationofProvenDraftSwitch(PDS1)
The PDS 1 is for indoor installation only. The PDS 1 must be installed in a vertical position with the pressure
  connectionpointingdown.Securetheswitchbyusingthemountingholesasshownonthegure.Afterinstallation
connect the tubing from the probe onto the port marked accessible through the small of the plastic enclosure.
Connect tubing to the NEGATIVE (-) port on the PDS.
Factory wiring comes with three wires that are already crimped onto the PDS. The purpose of these wires is to
provide a point in which you can extend the length of the wire by using wire nuts and additional wire (not provided).
3.2InstallationofStackProbeforPDS1
A stack probe is used with ENERVEX Proven Draft
Switches (PDS). The PDS 1 monitors the pressure
inside the stack and signals the control to shut down the
  applianceifinsufcientdraftexistsinsidethestack.The
probe must be installed between the appliance and
the exhaust fan.
For all installations, the stack probe must be placed
  s o theowthroughthestackisperpendiculartothetip
of the probe. Locate the probe at least the distance
“A” away from any elbows or tees in the stack.
  T h e distance“A”isdenedasatleast
  three(3)ventdiameters;A≥3*V(seegurebelow).To
prevent condensation from entering the probe or PDS
when installed on a horizontal stack, the probe
must be installed above the centerline of the stack. For
  replaceinstallations,thestackprobeshouldbe 
installed as close to the exhaust fan as possible.
ENERVEX
ENDURA PLASTICS
XP042105-1-1
REV A
0.05” WC PR
MOUNT DIAPHRAGM VERTICAL
UR
Mounting holes
Connection for
tubing at the bottom of
the enclosure
BRACKET ASM.
SELF TAPPING SCREWS
(RECOMMEND 1/4-20 OR M6)
(NOT PROVIDED
)
GASKET
PROBE
FERRULE
END CAP
View of PDS 1 Stack Probe
ENERVEX®
Solenoid Gas Valve (PV-GS-SGV-01)
Voltage 1 x 120V AC
Amperage 0.15
Temp. Limits 14°F to 176°F
Pipe Size ½” NPT
Max. Height 3.875”
Max. Length 3.5”
Max. Width
2.0”
System Switch (PV-ES-PLS-WHT-02)
Voltage 1 x 120V AC
Amperage 15
Temp. Limits -20°C to 60°C
Height 4.20”
Depth 0.97”
Width
1.32”
Faceplate
not included