User Guide

4
5
6
April 11, 2016
Enerlites offers a 2 years warranty on this product to be free of
defects in material and workmanship. This warranty is voided if
this product is installed improperly or in an improper environment,
overloaded, misused, or altered in any manner. Enerlites is not
liable for consequential damages arising out of, or in connection
with the use or performance of this product or other indirect
damages with respect to loss of property, revenue or profit or cost
of removal, installation or reinstallation.
Automatic Humidity:
Light (Manual On/Automatic Off),
Fan (Automatic On/Automatic Off)
The device is pre-set at the factory and required to turn on the light
manually and turn on the fan automatically when excess humidity is
detected. The sensor keeps the light on when there is occupancy and
automatically turn
s off if no movement is detected and the time delay
setting has expired. The fan will turn off after the humidity level has
dropped under the set humidity level. If the humidity level of an
enclosed space is still over the preset humidity level after the fan has
run for 30 minutes, it will turn off and continue to run after a 20 minute
break.
Automatic On/Automatic Off with PIR:
The light and fan will turn on automatically with PIR motion detection
and turn off automatically based on the occupancy and humidity levels
respectively. During the light/fan "on" state, the light will turn off
automatically if no movement is detected and the time delay setting has
expired. However the fan will continue to operate if the sensor detects
excess humidity and will automatically turn the fan off after 3 minutes
when the humidity level has dropped.
Manual On/Automatic Off:
The light and the fan will turn on manually and turn off automatically
based on occupancy and humidity level respectively. During the light/
fan "on" state, the light will turn off automatically if no movement is
detected and the time delay setting has expired. However the fan will
continue to operate if the sensor detects excess humidity and will
automatically turn the fan off after 3 minutes when the humidity level has
dropped.
Manual On/Manual Off:
At any time the light and the fan can be manually controlled with their
push buttons at the front of the switch.
Functions
Time Delay
Photocell
Humidity
*Factory Default
Quick Installation
15
Seconds
5FC
Medium
30
Minutes
Disable
Fan
LED Indicator
Flashing
Solid
Medium
Operation
Mode
Automatic
Humidity
Automatic
Humidity
Factory Default and Quick Installation Setting
1. 15 seconds (*)
2. 5 minutes
3. 15 minutes
4. 30 minutes
Function 2: Operation mode
Function 3: Ambient light level (photocell)
to keep the light off if the ambient light is sufficient
1. Disabled
2. 5 foot-candle (*)
3. 10 foot-candle
4. 20 foot-candle
Function 4: Humidity level (Humidity Range 80% - 45%)
1. High humidity sensitivity
2. Medium humidity sensitivity(*)
3. Low humidity sensitivity
TROUBLESHOOTING
Note: When the PIR sensor detects movement the
light button's green LED indicator will flash. The fan's
LED will turn red when the sensor detects excess
humidity in a room; otherwise, it will always stay lit in
white.
Function 1: Time delay for the light and the fan
1. START: programming mode
Press and hold the light button for eight seconds until the solid
green LED lights up, (its LED will stay on). The sensor is now in
programming mode.
a. The LED light will stay on for 20 seconds, awaiting next step.
b. If the button has not been pressed within 20 seconds, the
LED light will flash three times and the sensor will exit the
programming mode.
2. CHOOSE: Functions from 1-4
Press the button "X" number of times to enter a function to
change, (the LED light will flash with each press).
Note: When the button stops, the sensor will then flash back the
current setting for that function, (the sensor will do this 10 times at
two-second intervals, and then go back its last status mode).
3. CHANGE: the settings under each function
Press the button "X" number of times for the new setting, (the
LED light will flash with each press).
Note: for demonstration purposes, the switch is set at Quick
Installation setting for the following example.
The switch buttons are not functional
Check if the device is installed and wired properly. The device requires a neural wire for
operation.
Press the light or the fan button
If the load does not work and the indicator light does not flash
Turn OFF power at the circuit breaker then check wire connections. Confirm the
neutral wire is connected, Black and Blue leads are connected to Hot/Line wire.
If the load operates normally, but the load will not turn off.
Change sensor's mode of operation to desired setting and set to higher humidity level.
NOTE: Do not use the switch to control a fan/light combination where this is the only
means of illumination or light installed. The device will not eliminate condensation
solely and must be used with a properly sized ventilation fan in an enclosed space.
WARRANTY INFORMATION
1. Automatic Humidity : Light (manual on, auto off), fan
(auto on/off depending on humidity level) (*).
2. Automatic On/Automatic Off with PIR: When motion
is detected, both the light and the fan turn on
automatically and turn off based on occupancy for the
selected time delay and humidity level.
3. Manual On/Automatic Off: Both the light and the fan
turn on manually, and turn off automatically based on
occupancy for selected time delay and humidity level.
1. Press and hold the light button for eight seconds, (the
green LED light should be solid).
2. Press the light button one time for Function 1: time delay
for the light and the fan.
3. The green LED light will now flash four times indicating the
current time delay, which is at 30 minutes.
4. Press the light button two times to choose time delay
setting of 5 minutes.
5. The green LED light now will flash two times confirming
the new setting.
6. Press and hold the light button for eight seconds until its
LED light flashes three times. The time delay setting is
now saved.
E
xample 1: C
hange the current time delay of the
switch from 30 minutes to 5 minutes as follows
.
Custom program features:
PREP: Review the Function Chart on the next slide
before proceeding with the programming. (During
programming, only the light button will be used and the
green LED light will flash)
FUNCTION SETTING
Note : When the button stops, the sensor will then flash back the
setting for that function, (the sensor will do this 10 times at two-
second intervals, and then go back to its last status mode).
4. SAVE: Setting
Press and hold the light button for eight seconds until its LED
light flashes three times, the program is saved.
22055B
To switch between factory default and quick installation setting simply
press and hold the light and fan buttons for 10 seconds and release
when the red LED indicator turns solid green.
Factory default settings are indicated with (*)
PUSH BUTTON FUNCTION CHART