Installation Manual

INSTALLATION INSTRUCTION
Voltage...................................................................... 120VAC, 60HZ
Load(Single Pole Circuit)
Time Delay.................................................1, 5, 10, 15, 20, 30 minutes
Environment.............................................Commercial Indoor use only
Humidity.................................................. 95% RH, non-condensing
Incandescent lamp.......................................................... 0-800Watt
Fan Motor............................................................................... 1/4 HP
INSTALLATION AND WIRING
FULL TWO -YEAR WARRANTY
DESCRIPTION AND OPERATION
TROUBLESHOOTING
The Timer Switch replaces standard single-pole wall switch for energy
savings throughout the home. It turns controlled lights or fans off when
the selected time expires.
Turning lights on with
the HET06A-R
is accomplished by pressing the
desired time selection or on/off button. Lights will remain on for the
duration of the time-out setting that was last used and turn on the indicator
light for that active time interval. Lights can be turned off before the
time-out setting expires by pressing the on/off button. To change the
time-out setting, press the desired time selection button and the HET06A-R
will reset to that countdown interval. The LED will flash for the last
10s of the desired time. When the Timer Switch is power on, all the
LED’S flash three times, it indicates that the Timer Switch is ready to set.
Features:
· Seven-button Preset Timer Switch
·Adjustable time delay:1, 5, 10, 15, 20, 30 minutes
·Replace a standard light or fan single pole switch
·Work with most common lighting types
·Ideal for closet, pantry, garage, laundry room, outdoor lighting and spa
The HET06A-R is a timer switch that turns OFF the connected light or fan
illuminates while the switch is OFF. One of the time button indicators is
when the selected time expires. The light under the ON/OFF button
always lit to indicate the last used timer.
Manual ON
T urn ON the connected light or fan by pressing the desired time button,
first time selection(1 minute).
or the ON/OFF button. If you press the ON/OFF button, it activates the
Manual OFF
While a timer is active, you can press the ON/OFF button to turn OFF
the connected light or fan without delay.
Changing the selected time
If you decide that you need more or less time than you originally
selected, restart the timer switch by pressing the button that matches
the amount of time you think you will need.
Hold Mode(Continuous Operation)
To turn timer On for extended periods of time, press and hold the push
button for more than 3 seconds. Timer enters HOLD mode, all 7
LED’S go off and the connected load is turned ON. To exit HOLD mode
press and release the push button. 2 LED’S go on and the connected
load turns OFF.
For your safety: Connecting a proper ground to the timer switch
CAUTION
provides protection against electrical shock in the event of certain
fault conditions.
If a proper ground is not available, consult with a qualified
electrician before continuing installation.
Only connect the HET06A-R to a Single Pole Circuit. The
HET06A-R is not suitable for 3-way switching. If the existing
wiring does not match the description for a Single Pole Circuit,
you should consult with a qualified electrician.
-02--01- -03-
Press ON/OFF button. The connected light or fan should turn ON. If not:
Wire the timer switch
·
Twist the existing wires together with the wire leads on the timer
switch as indicated in the drawing. Cap them securely using the
wire nuts provided.
·Connect the green or non-insulated(copper) GROUND wire from
the circuit to the GROUND wire on the HET06A-R.
·
Connect the power wire from the circuit (HOT) to the black wire
on the HET06A-R.
·
Connect the power wire to the lamp or fan (LOAD) to the red wire
on the HET06A-R.
·Connect the NEUTRAL wires from the circuit (NEUTRAL) to the
white wire on the HET06A-R.
To test the timer switch
The light under the ON/OFF button should be ON when the switch is
OFF. The indicator light beside one of the time selection buttons is ON. Press
the ON/OFF button. The connected light or fan comes ON. The connected
light or fan should turn OFF in the number of the minutes indicated by the
time selection indicator light. You can turn it OFF sooner by pressing the
ON/OFF button again.
Light or fan will not turn ON (the indicator under the ON/
OFF button is on)
·Check the light bulb and/ or motor switch on the fan mechanism.
·Turn OFF power to the circuit then check wire connections.
Light or fan will not turn ON (the indicator under the
ON/OFF button is OFF)
·Turn OFF power to the circuit then check wire connections.
Make certain that the circuit breaker is ON and functioning.
·Check the light bulb and/ or motor switch on the fan mechanism.
Light or fan will not turn OFF
·
Press the ON/OFF button. If connected light or fan does not turn OFF
,
turn OFF power to the circuit then check wire connections.
If within two(2) years from the date of purchase, this product fails
due to a defect in material or workmanship, we will repair or replace
it, at its sole option, free of charge. This warranty does not apply to:
(a) damage to units caused by accident, dropping or abuse in handling,
acts of God or any negligent use; (b) units which have been subject
to unauthorized repair, opened, taken apart or otherwise modified;
(c) unit not used in accordance with instructions; (d) damages
exceeding the cost of the product; (e) sealed lamps and/or lamp
bulbs, LED’s and batteries; (f) the finish on any portion of the product,
such as surface and/or weathering, as this is considered normal
wear and tear; (g) transit damage, initial installation costs, removal
costs, or reinstallation costs.
This warranty service is available by returning the product with proof
of purchase date and a description of the problem to the dealer from
whom the unit was purchased.
HET06A-R
TIMER SWITCH
7-BUTTON PRESET
6 time selection buttons with
activation indicator lights
ON/OFF Button
with hold on function
SPECIFICATIONS
INTRODUCTION
Operating Temperature................ ................32.......
to 131
F(0
to 50
°
°
℃
°
15
20
30






)
Wiring Diagram:
HOT(BLACK)
LOAD(RED)
NEUTRAL(WHITE)
GROUND(GREEN)
22016A
Nov, 2014
Fluorescent lamp................................................................0-800VA