Owners manual

Must reuse original hardware
(When specified)
1
Instruction sheet for set # 3.4110
67-72 Chevy K5 Blazer 4WD
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
Position #3 - 6
1. Body.
2. Supplied washer P/N 15.03.11.39.
(3” O.D. x 9/16” I.D. x 1/8”)
3. Supplied sleeve P/N 15.10.50.39.
(7/8” O.D. x 11/16” I.D. x 1.80” Lg.)
4. 4054 Top bushing.
5. Frame.
6. 4056 Lower bushing.
7. Supplied washer P/N 15.03.06.39.
(2” O.D. x 3/8” I.D. x 1/8”)
Position #2
1. Body.
2. Supplied washer P/N 15.03.11.39.
(3” O.D. x 9/16” I.D. x 1/8”)
3. Supplied sleeve P/N 15.10.50.39.
(7/8” O.D. x 11/16” I.D. x 1.80” Lg.)
4. 4053 Top bushing.
5. Frame.
6. 4055 Lower bushing.
7. Supplied washer P/N 15.03.05.39.
(2” O.D. x 1/2” I.D. x 1/8”)
Position # 1
1. Core -support.
2. Supplied washer P/N 15.03.07.39.
(2-1/2” O.D. x 7/16” I.D. x 1/8”)
3. Supplied sleeve P/N 15.10.17.39.
(7/8” O.D. x 5/8” I.D. x 1.960” lg.)
4. 4025 Top bushing.
5. Frame.
6. 4056 Lower bushing.
7. Supplied washer P/N 15.03.09.39.
(2” O.D. x 7/16” I.D. x 1/8”)
1
3
2
4
5
6
7
Parts Diagram
NOTE: When disassembling the body mounts, be sure to note the number and position of shims that may have been used to align the
body. These shims will have to be reused to retain proper body alignment.
CAUTION: Remove all the body mount bolts on one side of the vehicle. Loosen but do not remove all the body mount bolts on the
opposite side of the vehicle. Only raise one side of the vehicle at a time, lifting the body only high enough to remove/replace the mounts.
Always watch the fan shroud, brake lines, and various hoses for sufficient clearance when raising the body. When jacking the body, use a
2x4 or equivalent to spread the weight. Never place jack faces directly on body panels! When all mounts and hardware are installed, torque
all bolts to factory specifications.
17017
2/DEC/09 BRH
It is recommended that if you are unfamiliar with this type of work that you refer to a qualified service center
specializing in this type of work. It is also recommended that if you choose to do this work yourself that a factory
service manual be obtained for the proper procedures pertaining to removal, replacement and proper torque
specifications for your vehicle. This instruction set is intended as a guideline for the safe installation of Energy
Suspension’s polyurethane bushings, once you have removed the factory components from your vehicle.
Updated 8/JAN/03 BRH Updated 23/JAN/04 BRH
Updated 14/JAN/05 BRH Updated 10/JAN/06 BRH
Updated 2/JAN/07 BRH
2008 Energy Suspension. All rights reserved.2008 Energy Suspension. All rights reserved.
CC
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
4
5
6
2
3