Owners manual

Position 4
#4006
#4007
Part#15.10.99.39
Part#15.03.05.39
Part#15.03.13.39
NOTE: Position # 2 is
for convertible only and
is supplied in set # 3.4152
Note the Quantities
and positions of
shims and re-use.
Supplied flat washer
2.00” x .500” x .125”
Supplied flat washer
1.750”x .438” x .120”
Supplied sleeve
.688” x .500” x .937”
Frame
Frame
Body
Body
Body
Installation instructions
3.4102 Coupe (hard top)
3.4152 Roadster (convertible)
3.4153 Seat belt cushions
63-67 Chevrolet Corvette
It is recommended that if you are unfamiliar with this type
of work that you refer to a qualified service center
specializing in this type of work. It is also recommended
that if you choose to do this work yourself that a factory
service manual be obtained for the proper procedures
pertaining to removal, replacement and proper torque
specifications for your vehicle. This instruction set is
intended as a guideline for the safe installation of Energy
Suspension’s polyurethane bushings, once you have
removed the factory components from your vehicle.
Updated 8/JAN/03 BRH
Updated 23/JAN/04 BRH
Updated 14/JAN/05 BRH
2005 Energy Suspension. All rights reserved.2005 Energy Suspension. All rights reserved.
CC
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
Read these instructions carefully before installing mounts.
NOTE: Be sure on disassembly to note the quantity and
positions of any shims or spacers that may have been
inserted for body alignment. These shims or spacers will
have to be re-used to insure proper body alignment. Position
# 2 is for convertible only. 63-64 Corvettes used cushions at
the seat belt mounts, be sure to remove the bolts from this
position before raising body. Install mounts one side at a time
with bolts on other side loosened only! Customer must reuse
or replace if O.E. hardware is unuseable (bolts, lock washers,
shims, spacers and nuts).
REMEMBER: Only raise body high enough to remove &
replace mounts. Always watch the fan shroud for sufficient
clearance when raising body. When jacking body use a long
enough 2x4 - 4x4 for maximum support. Never put jack
directly on body panels. Re-torque to factory specifications.
NOTE: Actual parts may vary from graphical depiction below.
17055
14/JUN/05 BRH
Frame
Positions 2&3
Position 1
#4007
Part#15.10.99.39
Supplied sleeve
.688” x .500” x .937”
Note the Quantities
and positions of
shims and re-use.
Part#15.03.05.39
Supplied flat washer
2.00” x .500” x .125”
#4006
Part#15.03.13.39
Supplied flat washer
1.750”x .438” x .120”
#4007
Part#15.10.99.39
Supplied sleeve
.688” x .500” x .937”
Note the Quantities
and positions of
shims and re-use.
Part#15.03.05.39
Supplied flat washer
2.00” x .500” x .125”
#4006
4
1
2
3
Part#15.03.13.39
Supplied flat washer
1.750”x .438” x .120”
#4233
Part#15.03.13.39
Supplied flat washer
1.750”x .438” x .120”
Set # 3.4153 63-64 Seat belt mount cushion
positions. Only the cushions and washers are
suplied, customer must reuse all O.E. hardware.
#4233
Seat belt cushion
positions
Frame Position Diagram