Installation Guide

BATTERY INSTALLATION
Puck: To open, twist back cover of puck light counterclockwise and
remove. Insert 3 AAA baeries per puck (noting polarity). To close,
replace cover and twist clockwise.
IMPORTANT: Dierent types of baeries or new and used baeries
should not be mixed. Exhausted baeries should be removed from
the fixture and disposed of properly.
Remote:
To replace exhausted baery, remove the screw and
baery cover, on the back of the remote. Insert 1 CR2032 baery,
noting polarity. Replace the cover and screw back in.
Note: Remove baery isolation tab before first time use.
MOUNTING INSTRUCTIONS:
1. Remove baery cover and use pre-
installed double-sided tape to mount in
desired location.
Note: For a more permanent
installation, screw through the two
holes using counter sunk screws.
Note: Ensure one of the two wireless
icons (
) remains unobstructed and facing desired direction for
remote to reach interior sensor. The remote will work beer with
direct line of sight access to the wireless icons (
).
2. Reaach light to mounted baery cover by aligning tabs and
twisting clockwise.
Note: Baery door may remain mounted when changing baeries.
REMOTE OPERATION:
1. On the remote, press the ON buon to turn the lights on, or press
the OFF buon to turn them o. The default seing is white.
2. Pressing the FADE buon will slowly cycle through the spectrum of
colors. Press again to stop on the current color.
3. Press the WHITE buon to switch the lights back to white.
Screw holes
4. Use the + and - buons to brighten or dim the lights.
5. The R, G and B buons stand for red, green and blue. These buons
allow you to either select one of these colors or blend them to select
the desired color.
a. Hold the R, G or B buon for three seconds to go directly to
that color.
b. Press and release the buons
repeatedly to move through the RGB
spectrum one color at a time.
c. Press and release the R, G and B
buons in any combination to create
custom colors.
6. The SAVE buon allows you to quickly
return to your favorite color. Once the
desired color is found, hold the SAVE
buon until the pucklight flashes. The color
will now be easily selectable by pressing
the SAVE buon. Once the color is set, you
can turn o the product and hit SAVE to
turn it back on to the set color.
7. The 10min, 30min, 60min and 120min
buons automatically turn the lights o
aer the number of minutes indicated on
the buon.
Note: When using the remote, point directly at the puck for proper
connection.
MANUAL OPERATION:
1. First press: turns the light on
in white
2. Second press: color-changing mode
3. Third press: stops on the current color
4. Fourth press: turns the light o
Functional range may be adversely aected by one or more of the
following factors: weather, radio frequency interference, low baery
or obstructions between the transmier and receiver.
Wireless Color-Changing Puck Lights
50014 EnSp Manual v1
06/10/2020
©2020 Energizer. Energizer and certain graphic designs are
trademarks of Energizer Brands, LLC and related subsidiaries
and are used under license by Jasco Products Company, LLC. All
other brand names are trademarks of their respective owners.
Neither Jasco Products Company, LLC nor Energizer Brands, LLC
is aliated with the respective owners of their trademarks.
Contact our U.S.-based Consumer Care at 1-800-654-8483
between 7AM-8PM CST.
90-day warranty. Visit www.byjasco.com for warranty details.
MADE IN CHINA/HECHO EN CHINA
READ IT OR WATCH IT
READ INSTRUCTIONS OR W ATCH
EASY-TO-FOLLOW V IDEO.
SCA N QR CODE OR VISIT
HTTP:/ / B IT.LY/ 3ATKYKH