SAFETY AND OPERATING MANUAL Original Instructions V12 18V COMBI DRILL ENE456COM
Read all safety warnings and all instructions before use. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
GENERAL SAFETY INSTRUCTIONS WARNING! Read all safety warnings designated by the symbol and all instructions. WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool 1) Work area a) Keep work area clean and well lit.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust-related hazards 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it is designed. b) Do not use the power tool if the switch does not turn it on and off.
SPECIAL SAFETY INSTRUCTIONS 1. Wear ear protection when using the impact drilling. Exposure to the noise can cause hearing loss. 2. Hold power tool by insulated gripping surfaces, when performing an operation where the drilling accessory may contact hidden wiring or its own cord. Drilling accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. 3. Remove the battery pack from the drill before carrying out adjustments. 4.
If there is an electrolyte leak, avoid any contact with the skin. In the event of a leak, wipe with a rag. If the liquid comes into contact with the skin, rinse abundantly with water. In the event of a reaction or contact with the eyes or mucous membranes, consult a doctor. Ensure that the appliance is properly switched off before inserting the battery into the appliance. Inserting a battery into a appliance while it is switched on can cause accidents.
NOISE INFORMATION Wear hearing protection! Measured sound values determined according to EN 60745. The noise figures quoted are emission levels and are not necessarily safe working levels. Whilst there is a correlation between the emission and exposure levels, this cannot be used reliably to determine whether or not further precautions are required. Factors that influence the actual level of exposure of work-force include the characteristics of the work room, the other sources of noise, etc. i.e.
This tool may cause hand-arm vibration syndrome if its use is not adequately managed. WARNING! Identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).
Important note Be sure the supply is the same as the voltage given on the rating plate. Remove the mains plug / battery pack before carrying out any adjustment or servicing. Intended use The machine is intended for driving in and loosening screws and bolts as well as for tightening and loosening nuts within the respective range of dimension. And it can be used to drill holes on wood, concrete or metal. When drill the hole in the steel, let the machine in low speed (not full speed).
SYMBOLS The symbols shown on the product has great significance for the safe use of the product. WARNING - To reduce the risk of injury, user must read the instruction manual Wear safety gloves Wear eye protection Wear ear protection Wear respiratory protection Double insulation Class II Conforms to all relevant safety standards. Charging time 3 to 5 h Do not dispose of batteries in a fire. They explode and result in injury.
Components and controls 1 2 3 4 5 6 7 8 9 Keyless chuck Torque adjustment ring Gear Control Forward, reverse rotation and lock control On/off switch with variable speed control Battery pack Battery pack release button Charging stand Charger 18V COMBI DRILL ENE456COM
TECHNICAL DATA Rated voltage: No load speed: Chuck capability: Number of clutch position: Maximum torque: Max drilling capability Machine weight: Normal charging time: Battery pack Charger Wood: Masonry: Steel: ENE456COM 18V 0-350 min-1/0-1250 min-1 10mm 20+1+ 1 18 N.m 16mm 10mm 8mm 1,8kg 3-5 hours ENE469BAT 18V Ni-Cd, 1300mAh ENB470CHR PRI: 230-240V~50Hz 20W SEC: 18V NOISE INFORMATION Sound pressure level : LpA = 86.5 dB(A) Uncertainty K=3dB(A) Sound power level : LwA =97.
CHARGING PROCEDURE 1. BEFORE USING THE CORDLESS DRILL If the machine is new, the battery must first be charged. A new battery or one which has not been used for an extended period achieves full performance only after few times charging and discharging cycles. Attention! After storing for a long time, the battery capacity will be reduced. A substantial drop in operating period per charge indicates that the battery is worn out and must be replaced.
Operating instructions 1. INSTALLING AND REMOVING BITS Warning! Always remove the battery before you change the drill or screw bit to avoid unintentional starting of the machine. Fig.1 1. Open the drill chuck by holding the rear section of the chuck and turn the front section in an anti-clockwise direction, until the jaws are open enough. (Fig.1) 2. Insert the bit firmly into the chuck.
6. REVERSIBLE The forward/reverse rotation control located above the On/Off switch controls the direction of rotation. For drilling and screw driving use forward rotation, slide the rotation lever to the right. To use reverse rotation, slide the rotation lever to the left to remove screws or release a jammed drill bit. (Fig.5) Fig.5 Warning! Never change the direction of rotation when the chuck is rotating, Wait until it has stopped. 7.
9. BIT STORAGE The backup bit can be placed in the storage area temporary during working. Just push the bit into the slot. (Fig.8) 10. LEVEL DRILLING Fig.8 The bubble level recessed in the motor housing on top can keep the drill level during horizontal drilling operation. The bubble level recessed in the motor housing on back of the drill can keep the drill level during vertical drilling operation.(Fig.9) 11. DRILLING Fig.
TERMS OF USE When all precautions have been taken and the previous operations were done, you can start working. Always secure the work piece especially if it is small and the sheets. Use the appropriate drill bit and the material at the correct speed. In the woods, a burned area indicates an inappropriate speed or a bit sharpened improperly. In steel, lubricate to prevent overheating and premature wear of the drill.
GUARANTEE This ENERGER product carries a guarantee of 12 months. If your product develops a fault within this period, you should, in the first instance contact the retailer where the item was purchased.
Declaration of Conformity We, Importer Powersmith (UK) LTD.
