SAFETY AND OPERATING MANUAL Original Instructions 7.
Read all safety warnings and all instructions before use. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
SPEICIAL WARNING FOR HAMMER CAUTION This is a very powerful Drill. When using this drill it is essential that the following rules for use are followed! 1. When drilling it is common that the core / drill bit jams in the material being drilled. This will result in the drill trying to rotate around the drill bit and potentially come out of your grip. This SDS Drill has a safety clutch mechanism.
3 Personal safety a) Stay alert, watch what you are doing and use common sense when operating the tool. Do not use the tool when you are tired or under the influence of drugs, alcohol or medication. One moment of carelessness while using a tool can result in serious personal injury. b) Use safety equipment. Always wear eye protection. Safety equipment such as dust masks, non-slip safety shoes, a hard hat and hearing protection used for appropriate conditions will reduce personal injuries.
11. After long working periods, external metal parts and accessories could be hot. 12. Wear eye protection when operating this tool. WARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm.
NOISE INFORMATION Wear hearing protection! Measured sound values determined according to EN 60745. The noise figures quoted are emission levels and are not necessarily safe working levels. Whilst there is a correlation between the emission and exposure levels, this cannot be used reliably to determine whether or not further precautions are required. Factors that influence the actual level of exposure of work-force include the characteristics of the work room, the other sources of noise, etc. i.e.
WARNING! Identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). Vibration and noise reduction To reduce the impact of noise and vibration emission, limit the time of operation, use low-vibration and low-noise operating modes as well as wear personal protective equipment.
Torque limiter There is a clutch in your hammer drill. The torque limiter will actuate when a certain torque level is reached. The motor will disengage from the output shaft. When this happens, the bit will stop turning. As soon as the torque limiter actuates, release the trigger and remove the tool and bit immediately. This will help prevent premature wear of the tool. Double insulation The tool is double insulated.
SYMBOLS The symbols shown on the product has great significance for the safe use of the product. WARNING - To reduce the risk of injury, user must read the instruction manual Wear eye protection Wear ear protection Wear respiratory protection Wear safety gloves Double insulation Class II Conforms to all relevant safety standards.
LIST OF MAIN PART 1 2 3 4 5 6 7 8 9 SDS chuck Carbon brush cover Auxiliary handle Front hammer/drill switch with locking knob On / off switch Rear hammer/drill switch Cable Dust cover Depth gauge 850W ROTARY HAMMER ENB465DRH
TECHNICAL DATA Model Rated voltage Rated power No load speed Max drilling capability Wood: Masonry: Steel: Weight ENB465DRH 230-240V~50Hz 850W 850min-1 40mm 26mm 13mm 4.2kg NOISE DATA Sound pressure level : LpA = 92.7 dB(A) Uncertainty K=3dB(A) Sound power level : LwA =103.
Operating instructions 1. FITTING AND REMOVING THE DRILL BITS NOTE: The device is supplied with a SDS-plus chuck. 1. Clean the tip of the accessory and lubricate it lightly with a light oil or lubricant before insertion. 2. Pull back and hold the fastening sleeve. 3. Insert accessory in SDS plus chuck while turning and pushing it until it engages. 4. Make sure the bit has been locked by pulling and turning. (Fig.
4. DUST COLLECTION DEVICE (Fig.5) NOTE: The dust cap is ideal when working overhead (vertically). It protects the user from falling dust which may restrict vision. 1. Before fitting the drill bit, pull the dust cap down the length of the drill bit ensuring the recessed end of the cap is pointing towards the tip of the drill bit. 2. Fit the drill bit into the chuck. 3. Adjust the dust cap before use so that it does not rest on the cutters of the drill bit. Fig.5 5.
HAMMER/DRILL SWITCH The hammer/drill switches can switch the drill, hammer and hammer/ drill functions. There is a lock knob in front hammer/ drill switch, please depressed it first to preventing any unintentional adjusting. WRNING! Please check and make sure the function switch has been fixed by locking knob after each adjustment.
DRILLING OPERATION Drilling wood 1. For drilling into wood, ensure the selection switch is set to the regular drilling function (drilling mode only). 2. When drilling into soft wood, the drill should be operated at high speed. 3. When drilling into hard wood, the drill should be operated at low speed. 4. Ensure you are using a twist drill bit. 5. Ensure the workpiece is clamped or anchored firmly before operation. 6.
TERMS OF USE When all precautions have been taken and the previous operations were done, you can start working. Always secure the work piece especially if it is small and the sheets. Use the hammer drill suitable for the material. Drilling: In the woods, a burned area indicates an inappropriate speed or a bit sharpened improperly. In steel, lubricate to prevent overheating and premature wear of the drill. In steel, it is recommended to drill out regularly to remove chips and cool the drill.
GUARANTEE This ENERGER product carries a guarantee of 12 months. If your product develops a fault within this period, you should, in the first instance contact the retailer where the item was purchased.
PLUG REPLACEMENT (UK & IRELAND ONLY) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE =NEUTRAL Brown = Live As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows. The wire which is colored blue must be connected to the terminal which is marked with N.
Declaration of Conformity We, Importer Powersmith (UK) LTD.
