SPECIFICATION LITHIUM-ION RECHARGEABLE BATTERY REFERENCE Product Name: INR14500A80 Capacity: 800mAh APPLICATION ENGINEERING DIVISION Revised on: Prepared by: Checked by: Approved by: 2011-8-15 Version: A Specification No.
Lithium-ion Rechargeable Battery Contents 1. Preface ------------------------------------------------------------------------------------------------------------------ Page 3 2. Application Range ---------------------------------------------------------------------------------------------------Page 3 3. Description ------------------------------------------------------------------------------------------------------------ Page 3 4.
Lithium-ion Rechargeable Battery 1. Preface This Product Specification describes the technique requirements, test procedures and precaution notes of Lithium-ion Rechargeable Battery to be supplied to Tensai International 2. Application Range This specification is applied to Lithium ion Battery INR14500A80 delivered to Tensai International 3. Description 3.1 Description Lithium ion rechargeable battery 3.
Lithium-ion Rechargeable Battery 5. Performance Curve 5.1 Charging Characteristics Charging Characteristics of INR14500A80 Current(mA) Charge: 0.5C,4.2V,CC-CV,0.01C cut-off, 25℃; 400 4.25 800 700 300 600 Voltage 500 200 3.75 400 300 Current Capacity 3.50 100 Capacity(mAh) Voltage(V) 4.00 200 100 3.25 0.0 0 0.5 1.0 1.5 2.0 0 2.5 Time(hour) Different Rate Discharge Characteristics Different Rate Discharge Characteristics of INR14500A80 4.4 4.0 0.2C 0.5C Voltage(V) 5.2 3.6 1C 3.
Lithium-ion Rechargeable Battery 5.3 Storage Characteristics Storage Characteristics of INR14500A80 120 100 Capacity(%) 80 60 40 Charge: 0.5C,4.2V,CC-CV,0.01C cut-off, 25℃; Storage: Three Months; Discharge: CC, 0.2C,3.0V cut-off,25℃; 20 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 Length of storage(months) Cycle Life Characteristics Cycle Life Characteristics of INR14500A80 900 800 700 Capacity(mAh) 5.4 600 500 400 Charge: 0.5C,4.2V,CC-CV,0.01C cut-off，25℃; Rest :30min; Discharge: 0.5C,3.
Lithium-ion Rechargeable Battery 6. Appearances There shall be no such defect as scratch, flaw, crack, rust, discoloration, leakage, which may adversely affect commercial value of the Battery. 7. Standard Environmental Test Conditions Unless otherwise specified, all tests stated in this Product Specification are conducted at temperature 20±5 ℃ and humidity 65±20%RH.
Lithium-ion Rechargeable Battery Items Test methods Judgment criteria 8.15 Short Circuit Short circuit the lead wire (resistance 30mΩ or under) across" + "and" - "terminals of the Battery after standard No fire. No explosion. charging. 8.16 Overcharge Test Charge by constant Current of 2C and constant voltage of 5V for 2 hours. 8.17 Overdischarge Test After standard charge .Discharged by constant Current of 0.2C to 3.
Lithium-ion Rechargeable Battery Prohibitions and Cautions in Handling the Lithium-ion Battery Pack 1. Scope This document defines the Prohibitions and Cautions in Handling the Lithium-ion Battery INR14500A80. The Battery which YLE supplies to Tensai is used for the battery pack. When the Battery is used under the different conditions from those stated in this document, different restrictions and conditions shall be applied.(YLE needs new tests in may be) Please consult YLE again.
Lithium-ion Rechargeable Battery 6. Cautions for Disposal of the Lithium-ion Battery 1) Dispose the damaged Battery during the battery pack assembly process etc. after taking necessary steps to prevent external short-circuit by the following methods. ●After insulating the terminals of the Battery with tape etc., dispose it under the law or ordinance of each local government. 2) As for the charged Battery, after discharging it with a resistor, dispose it by the above method. 7.
Lithium-ion Rechargeable Battery Product Drawing Symbol Revision Date Signed A Checked A +0.2 φ13.9-0.1 mm +0.2 φ14.0-0.1 mm ±1 48.8± 0.2mm 48.8± 0.2mm φ9 A side PVC tube B B 图1 Without PVC tube B side 图2 With PVC tube ② Outer Jacket PVC 1 ① Battery INR14500A80 1 Symbol Name Name Qty Scale Free Checked Checked Approved Process Model NO.
