Full Manual 1/2.
Table of contents 1. Safety Instructions and Notes…....................................................................................................... 4. Part names…………………………….…...................................................…………………………... 3 3 5 6 5. Installation Instructions......................................................................................……………………... 7 6. Setup Menu ……………............................................................................…………………………... 13 2.
WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. The symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the unit. The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
1. Safety Instructions and Notes • Please read this safety and operating instructions before putting the camera into operation. • Keep the manual in a safe place for later reference. • Pay attention to safety when laying the connection cable and observe that the cable is not subjected to heavy loads, kinks or damage and no moisture can get in. • Never open the device such as boards or lens. The warranty becomes void if repairs are undertaken by unauthorized persons.
• SMART MOTION ZOOM(Automatic Zoom IN/OUT when motion is detected) • Pointing Zoom which enables the flexible zooming at any area • Motion Detection / Motion Deblur / Privacy Mask / Defog • Focusing Status Indicator on Screen - (Blue) Focusing in process - (White) Focusing Completed • Pixel Defect Compensation • ID / TITLE / ZOOM RATIO Display • H / V / HV FLIP • Lens Refresh / Lens Initializing Set / LSC(Lens Shade Compensation) • Enhanced Sensitivity by DSS technology • Menu Control via either Local Joy
3.
ⓓ 4.
5. Installation 5.1 Installation Instructions WARNING NEVER USE THIS CAMERA 1) in WATER. 2) in area where has SHOCK or VIBRATION which results in the problems for Auto Focus operation. • Make sure the power is removed before the installation. • Follow the order for applying power. First, connect the low voltage (AC24V or DC12V), then plug the AC adapter to AC outlets to avoid an improper reset from power jitter and a damage from the surge voltage when no load.
5.2 Surface mount Ceiling or wall Quick installation guides; Surface mount base 1. Locate the mounting template at the installation position and drill the ceiling or wall if needed. ⑥Mount screws 2. Place Surface mount base on pre-drilled position and fix it through ⓙSurface mount holes(x4) by using ⑥Mount screws. Assemble the cable pipe, otherwise tighten ①pipe hole cap. and ②pipe hole cap for surface mount base 3.
5.3 Flush mount Ceiling or wall Quick installation guides; 1. Locate the mounting template at the installation position and drill the ceiling or wall if needed. Dome base assembly ⑥Mount screws Dome bubble assembly 2. Open Dome bubble assembly by loosening ⓘRing cover fixing screws(x3) CAUTION Extreme care should be taken NOT to scratch the dome surfaces and to protect it from dirt or dust at any time. 3.
5.4 Limit of pan and tilt 1. Pan limit Pan is limited to +/- 165°. Do NOT force to rotate the gimbal over the limit to prevent from the internal damage. 2. Tilt limit Tilt is limited to 15° min ~ 90° max. with reference to the ceiling when the inclination of camera module is 0°, that is, the image is aligned horizontally. CAUTION : Tilt may NOT reach 15° min. if some IR light reflects to the lens when the inclination is NOT 0°.
5.5 Installation and commissioning Instructions • Make sure the power is removed before the installation. • After all connections are finished properly, follow the order for applying power. a) Plug the network cable into RJ-45 Ethernet Port at the rear panel. If PoE is the unique power, there will be no need to connect Power terminal.
5.2.1 EMI Ferrite Core Connections Please connect EMI Ferrite Core as below photos.
6. Setup Menu 6.1 Quick Network Setup The network camera‘s default IP address is: 192.168.1.10. Therefore, to access the camera for the first time, set the PC‘s address as 192.168.1.XX; for example: IP Address: 192.168.1.20 Subnet Mask: 255.255.255.0 • Enter the camera’s IP address in the URL bar of the Web browser window and hit “Enter.” • Enter the default user name (root) and password (root) in the prompt request dialogue.
If the Information message doesn‘t come out due to the problems like network failure, you can start the manual installation. Click the Install ActiveX Control, and the pop-up window will be displayed. After the installation is successfully completed, Smart Viewer window will be displayed. - Assigning an IP address To assign an IP address to the camera proceeded as follows: Click Network Configuration on the Network Configuration menu.
Depending on the service type, the network configuration can be in any of Static IP, DHCP Client, or PPPoE. You need to set up the network camera according to your network type. For static IP, select static IP and input values for IP address, NetMask, Gateway, DNS1, DNS2 and click apply for saving settings. After apply, program will ask closing web browser for updates, which will take 20~30 seconds. For DHCP, DHCP server must exist in the same network environment.
PPPoE is used to connect IPproducts to PPPoE modem provided by ISP. Since PPPoE needs verification, ID and password are necessary to access network. Type in ID and password.
- Administrator password To change the password for the administrator, click Admin Password on System Configuration menu. Default ID for admin account is fixed as “root” and not allowed to change. In Old Password field, enter the current password. In both New Password and Confirm Password fields, enter the same new password. The password must be between 4 and 23 alphanumeric letters. Click Apply button to put it into effect.
- Accessing the setup menu Camera SETUP menu can be accessed in two ways via web viewer. Most frequent controls are available with the parameters directly in the below table. More complicated settings such as PRIVACY, POINTING ZOOM & SMART MOTION settings are available via ‘ADVANCED CAMERA MENU’ by activating the camera OSD menu.
6.2 Direct Control menu SPECIAL Default TV SYSTEM US or EU Descriptions Selects HDTV standards for US(60HZ) or EU(50HZ). nd By this selection, 2 analog video output switches to NTSC or PAL accordingly. ZOOM PUSH, AUTO and MANUAL modes are available for focusing. FOCUS MODE D-ZOOM ZOOM PUSH OFF ZOOM PUSH – Focusing is activated only when zoom in/out is working. AUTO – Focusing is always working. MANUAL – Focusing can only be adjusted by ▲,▼ of OSD control joystick or Focus Near/Far button on WEB.
Improves the visibility for the high bright area and the dark area by the double captures of image with LONG and SHORT exposures. With WDR ON, the frame rate becomes half by the double captures. WDR OFF WDR Weight MID Back Light Compensation (BLC) OFF ※CVBS video signal Connecting 2nd video to CVBS port disables WDR function temporary. It should be considered when installer adjusts the video with installation monitor via CVBS video signal. WDR level can be selected from LOW, MID and HIGH.
ATW, ONE PUSH and MANUAL are available for the white balance modes. WHITE BAL ATW WB Manual R-Gain 10 ATW – White balance is continuously working along with the color temperature changes in the range of 2,000K~8,500K. ONE PUSH- White balance works only when ONE PUSH is selected. MANUAL –This mode can be used only when the color temperature does not vary. White balance is fixed to the settings by R_GAIN and BGAIN. Activates when WHITE BALANCE is set to MANUAL. Adjustable 0~20.
Display Title IR LED Mode OFF ON enables to display Camera Title on Monitor. OFF IR LED Control(AUTO/OFF) is available with IR LED model only. If IR LED is set to OFF, IR LED will be turned OFF but DAY or NIGHT is still determined by the built-in light photo sensor. IR LED Mode is workable with IR LED built-in model only.
SPECIAL PRIVACY MOTION Default - OFF Descriptions 10 Privacy zones which can be enabled individually by ZONE DISP are available to mask the video. ZONE NUMBER – Set a number to select a privacy zone from 1~10. ZONE DISP – ON enables a relevant privacy zone. H-POS, V-POS, H-SIZE and V-SIZE – Adjust the size and position of zone. COLOR – Select the color used for masking the zone form eight colors. TRANSPARENCY – Defines the transparency for the mask zone.
SMART IR can be set to reduce the saturation by the strong IR illumination in the night in any menu of EXT, AUTO and B/W(NIGHT) Setting SMART IR in any menu is identically applied to other menu. Zero(0) turns off SMART IR and High setting avoids the saturation strongly but the corners will be darker accordingly. SMART IR 0 MOTION DEBLUR ON ON enables MOTION DEBLUR to reduce the motion blur in a certain indoor enviroment. Noise or color rolling can increase.
6.3.1 SMART MOTION ZOOM SMART MOTION ZOOM enlarges the certain area defined by a yellow window to the full sized image when the motion is detected in the black window. SMART MOTION ZOOM window can be re-sized by adjusting D-ZOOM RATIO and moved by H-POINTER and V-POINTER. UNLIKE the conventional zoom which can zoom in/out the center area of image only, by the flexible zoom location and area, SMART MOTION ZOOM differentiate its usefulness from others.
6.3.2 POINTING ZOOM This camera has a very useful and powerful feature, POINTING ZOOM, which can zoom in/out any area. UNLIKE the conventional zoom which can zoom in/out the center area of image only, by the flexible zoom location and area, POINTING ZOOM differentiate its usefulness from others. That is, a conventional camera installed on the corner of ceiling can zoom the center of the floor in a room and result in losing the image of door on the side wall.
7. Specifications PXD-2080Z03 B 207513 Imaging Sensor Sony Exmor 1 / 2.9” Progressive Scan CMOS Sensor Effective Pixels 1,936(H) x 1,097(V) Min. Illumination 0.0008 Lux (@AGC MAX, DSS x2) Output Video Resolution TV system Sync.
Power PoE(IEEE Std. 802.
8.
eneo® is a registered trademark of Videor E. Hartig GmbH Exclusive distribution through specialised trade channels only. Videor E. Hartig GmbH Carl-Zeiss-Straße 8 · 63322 Rödermark/Germany Tel. +49 (0) 6074 / 888-0 · Fax +49 (0) 6074 / 888-100 www.videor.com www.eneo-security.com Technical changes reserved © Copyright by Videor E.
