INSTALLATION AND OPERATION MANUAL for HDC-2080Z03
Table of contents 1. Safety Instructions and Notes…....................................................................................................... 4. Part names…………………………….…...................................................…………………………... 3 3 4 5 5. Installation Instructions......................................................................................……………………... 6 6. Setup Menu ……………............................................................................…………………………... 6 2.
WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. The symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the unit. The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
1. Safety Instructions and Notes • Please read this safety and operating instructions before putting the camera into operation. • Keep the manual in a safe place for later reference. • Pay attention to safety when laying the connection cable and observe that the cable is not subjected to heavy loads, kinks or damage and no moisture can get in. • Never open the device such as boards or lens. The warranty becomes void if repairs are undertaken by unauthorized persons.
• Wide Dynamic Range • 3D Noise Reduction • Sense Up(~x8) / AGC(0~20) • Scale down the image to 720p without loss of field of view • MOTION ZOOM(Automatic Zoom IN/OUT when motion is detected) • Pointing Zoom (Set the off-centered location to be the center of zoom in Motion Zoom) • Motion Detection / Motion Deblur / Privacy Mask / Defog • Focusing Status Indicator on Screen -(Blue) Focusing in process -(White) Focusing Completed • Pixel Defect Compensation • ID / TITLE / ZOOM RATIO Display • H / V / HV FLI
4. Part Names ④ Front view ③ ⑤ ① ② ① ② ③ ④ ⑤ Window Window Hood Front Body Mount Hole (Top and Bottom) Rear Body 4.
5. Installation and commissioning Instructions • Make sure the power is removed before the installation. • Follow the order for applying power. First connect the low voltage (DC12V or AC24V), then plug the AC adapter to AC outlets to avoid an improper reset from power jitter and a damage from the surge voltage when no load. 5.1. Installation The camera has a 1/4” thread insert on its top and bottom side for mounting the camera to a tripod or the wall or ceiling with a corresponding mount. 5.2.
In the menu, use ▲,▼ to move menu, ◀,▶ to change the settings and press ☟ to select or enter. The actual value of FACTORY DEFAULT may differ from this manual due to further technical improvements. 6.2 MAIN menu Press ☟ to enter the setup menu for about 1 second. MENU V2.0 1. ZOOM/FOCUS 2. EXPOSURE 3. SCENE ENHANCE 4. 3D-NR 5. DAY/NIGHT 6. PICT ADJUST 7. SPECIAL 8. SYSTEM 9.
MAIN Default SCENE ENHANCE NORMAL 3D-NR MID Descriptions NORMAL – Optimized for the normal indoor and outdoor in the good lighting condition. WDR – Improves the visibility for the high bright area and the dark area by the double captures of image with LONG and SHORT exposures. With WDR ON, the frame rate becomes half by the double captures. WDR level can be selected from LOW, MID and HIGH.
6.3 ZOOM/FOCUS ZOOM / FOCUS FOCUS MODE D-ZOOM LENS REFRESH LENS INIT. RETURN ZOOM / FOCUS ZOOM PUSH OFF OFF ON RET↵ Default Descriptions ZOOM PUSH, AUTO and MANUAL modes are available for focusing. FOCUS MODE D-ZOOM LENS REFRESH ZOOM PUSH ZOOM PUSH – Focusing is activated only when zoom in/out is working. AUTO – Focusing is working always. MANUAL – Focusing can only be adjusted by ▲,▼ of OSD control joystick or the remote control via RS-485. OFF D-ZOOM(Digital zoom) is available up to 32x.
6.4 EXPOSURE EXPOSURE MODE AUTO BRIGHTNESS |:::::::|::::::| 10 SENS-UP AUTO↵ AGC |::::::::|:::::| 12 MOTION DEBLUR ON RETURN RET↵ EXPOSURE Default Descriptions Can set EXPOSURE MODE to AUTO, IRIS Priority, SHUT. Priority, MANUAL and Flickerless. MODE AUTO AUTO – Optimizes the video level by controlling the iris and the shutter speed automatically. IRIS Priority – Selects to fix IRIS in a certain apperture and the video level is controlled by an automatic shutter control.
6.5 PICT ADJUST PICTURE WHITE BAL SHARPNESS COLOR GAIN GAMMA RETURN PICTURE ATW |:::::|::::::| 10 |:::::|::::::| 10 0.5 RET↵ Default Descriptions ATW, ATWext, ONE PUSH and MANUAL are available for the white balance modes. ATW – White balance is continuously working along with the color temperature changes in the range of 2,000K~8,500K. ATWext – White balance is continuously working along with the color temperature changes in the range of 1,800K~11,000K.
6.6 SPECIAL SPECIAL MIRROR/FLIP PRIVACY MOTION PIXEL DEFECT TITLE SET DISPLAY DEFOG RETURN SPECIAL OFF OFF OFF OFF ↵ ↵ OFF RET↵ Default Descriptions Reverses the video left and right and/or up and down by MIRROR/FLIP. MIRROR/FLIP PRIVACY OFF OFF OFF - Normal display without mirroring or flipping Hor. – Video is reversed left and right. Ver. – Video is reversed upside down. HV – Video is reversed left and right and upside down. When the video is reversed by Ver.
MOTION OFF MOTION can detect the changes in the motion window and displays the results in blocks and/or a text message. SENSITIVITY – Adjusts the detection sensitivity for motion. High value increases the sensitivity to detect the small motion easily. Too low sensitivity will cause the erratic detection by the tree leaves or the light level changes. H-POS,V-POS, H-SIZE and V-SIZE - Adjust the size and position of the detection window. BLOCK DISP – ON enables to display the blocks for the detected area.
DISPLAY DEFOG - OFF Enables or disables to display the OSD. ID – ON enables to display the camera ID defined by SYSTEM>COMM. SETUP>CAM ID. TITLE – ON enables to display the camera title(name) set by SPECIAL> TITLE SET. ZOOM RATIO – ON enables to display the zoom ratio on the bottom right corner. OZx.x appears during the optical zoom and DZx.x will display by multiplying the optical zoom ratio and the actual digital zoom ratio.
6.7 SYSTEM SYSTEM TV SYSTEM RESOLUTION COMM. SETUP LANGUAGE FACTORY DEFAULT RETURN SYSTEM Default TV SYSTEM EU RESOLUTION COMM. SET UP LANGUAGE 1080P US(60HZ) 1080P ↵ ENG☟ NO RET↵ Descriptions Selects HDTV standards for US(60HZ) or EU(50HZ). nd By this selection, 2 analog video output switches to NTSC or PAL accordingly. 1080P and 720P are available. 720P Image is scaled down from 1080P without loss of field of view 1080P outputs the frame rate at 30P/25P.
7. Specifications HDC-2080Z03 Imaging Sensor Sony Exmor 1 / 2.9” Progressive Scan CMOS Sensor Effective Pixels 1,936(H) x 1,097(V) Min. Illumination 0.0008 Lux (@AGC MAX, DSS x2) Output Video Resolution TV system Sync. System 1920x1080( 30p/25p), 1280x720(60p/50p) EU(50Hz)(switchable to US(60Hz)) Internal Format 16:9 Video format for most popular commercial HDTV monitors HD-SDI Video Output 1.
8.
18
19
