Quick Installation Guide Fastrax III 1/4” Day/Night Dome Camera, PTZ, 22x EDC-3222
Contents 1. Safety Instructions / Maintenance.................................................................................................................................................................................... 3 2. Introduction..................................................................................................................................................................................................................... 3 3. Installation and Configuration...............
1. Safety Instructions / Maintenance • Read these safety instructions and the operation manual first before you install and commission the camera. • Keep the manual in a safe place for later reference. • Protect your camera from contamination with water and humidity to prevent it from permanent damage. Never switch the camera on when it gets wet. Have it checked at an authorized service center in this case.
Alarm Input (up to 8) Alarm Output (up to 4) up to 255 multiplexers up to 99 DVRs up to 254 cameras including 64 alarm modes Figure 1 - Typical System Configuration push bubble ring ass’y remove camera window screw push Remove window Assemble bubble ring ass’y Figure 2 - Optional Assemble bubble ring ass’y NOTE: It is recommended to remove camera window for improving picture quality when you assemble bubble ring ass’y.
3. Installation and Configuration 3.1 Package Contents The package contains the following: 1x Fastrax III (Dome Camera) 1x Bubble ring (optional) 1x Instruction manual 3x Assembly screws for attaching Fastrax III 3x Plastic anchor 1x 10Pin Connector 2x 12Pin Connector CAUTION: B e sure to have caution labels (E version only) on both body and base of the camera. Different version will not support alarm input and output.
3.
SW1: Termination switches SW2: Fail-Safe Network Addresses (ID) and protocol selection switches Figure 5 - Layout of Switches 3.3 Setting Dome Camera Termination The device which is connected at end of line, whether it be a dome camera or keyboard controller, must have the cable for communication terminated by setting the appropriate DIP switch. Without proper termination, there is potential for control signal errors. Total length of the cable for communication should not exceed 1.2km.
3.4 Fail-safe Network When you control the dome by the other device not own keyboard, some error may be existed in the serial communication. The reason is caused by the other device without the fail-safe network. At this time, you solve the problem to set this DIP switch to ON of the nearest dome from the other device only.
3.5 Setting Dome Camera Address (ID) To prevent damage, each dome camera must have a unique address (ID). When installing multiple dome cameras using a multiplexer, it is suggested that the dome camera address matches the multiplexer port number. If you wan to set the address more than 999, you should connect the service provider. Example: Port 1 = Dome 1, Port 2 = Dome 2 ... Port 16 = Dome 16.
3.6 Setting Dome Camera Protocol If a dome camera is to be installed with a Fastrax keyboard controller, select the default protocol. Consult service personnel if a dome camera is installed with device other than a keyboard controller.
3.7 Connections • Connecting to the RS-485/-422 The dome camera can be controlled remotely by an external device or control system, such as a control keyboard, using RS-485 half-duplex, RS-422 full duplex or simplex serial communications signals. Connect Marked Tx+, Tx- to Tx+(Rx+) and Tx-(Rx-) of the RS-485 control system. If control system is RS-422, connect Rx+(Tx+), Rx+ (Tx-) and Rx+, Rx- of the dome camera to Rx+, Rx- and Tx+, Tx- of the control device respectively.
4. Program and Operation 4.1 Dome Camera Selection Before you program or operate a dome camera, you must select the dome camera by pressing the dome camera No. + CAM. Example: Pressing 1, 0 and CAM key sequentially will select dome camera 10. The selected dome camera ID will be displayed on the LCD monitor of the keyboard controller. 4.
5. Short Cut Key Short Cut Key PRST TOUR PTRN SCAN NO.
6. Specifications Type EDC-3222 Art. No. 74193 Series eneo Fastrax III System day&night Video standard CCIR/PAL Sensor size 1/4” Imager CCD, Sony ExView HAD Interline Transfer Active picture elements 795(H) x 596(V) pixels Horizontal resolution 580 TVL Synchronization Internal/AC line lock, phase adjustment via remote control Signal-to-noise ratio 50dB (AGC OFF) Sensitivity (at 50% video signal) 1.0 Lux, (colour), 0.1Lux (B&W) at F1.
Patterns 8 patterns up to 500sec.
eneo® is a registered trademark of Videor E. Hartig GmbH Exclusive distribution through specialised trade channels only. VIDEOR E. Hartig GmbH Carl-Zeiss-Straße 8 · 63322 Rödermark/Germany Tel. +49 (0) 6074 / 888-0 · Fax +49 (0) 6074 / 888-100 Technical changes reserved. www.videor.com www.eneo-security.com © Copyright by VIDEOR E.
