User`s manual

• Outside the pool, thread in the male portion of the street elbow
(#6) into the tailpiece of the thru-wall fitting (#8).
• From inside the pool, thread the eyeball fitting into the thru-wall
fitting (#8). Point the eyeball towards the bottom of the pool for
optimal water circulation in the Fastlane Pool.
• When the water quality system equipment needs maintenance,
the eyeball fitting should be removed and the provided plug
should be threaded into the thru-wall fitting (#8) to prevent the
pool from draining.
DIAGRAM #4: RETURN WALL FITTING DIAGRAM
DRAINAGE
Drainage needs to be provided around the pool and near the water
quality equipment. It is important to be prepared in the unlikely
event of a leak. If operating the Fastlane Pool indoors, it is ideal to
install floor drains in the area around the pool’s perimeter, but not
directly under the pool. It is worth the time and effort now to install
a drainage system rather than be unprepared in the event of a mishap.
FASTLANE HYDRAULIC POWER
UNIT ASSEMBLY
The power unit should placed on flat and level surface. Whether
placed indoors or outdoors, this is an air-cooled unit and must have
ample ventilation. Therefore, a minimum of 12" of air spaced must
be provided on all sides of the power unit. In addition, the power
unit needs to be check periodically for maintenance and should be
accessible.
The power unit is heavy, care should be taken when placing the power unit.
Once the power unit is in place, connect the run hoses. The low
pressure hose, which will have red tape, gets connected to the con-
nection on the black fill cap. The high pressure hose gets connected
to the fitting on the high pressure manifold.
Make sure that the power is turned off to the power unit. Remove
the fill black fill cap and remove the oil filter by lifting it out of fill
opening. Use the provided paper funnels and fill the reservoir to
with in 2" of the top. Once filled, replace the oil filter and ensure
that it is seated properly before putting the fill cap back on. If you
have selected a longer run hose, we have provided extra fluid. In
this case, turn the unit on and let it run for one minute to fill the run
hoses. Turn the power off, remove the fill cap and oil filter, and add
fluid as needed. Again, you want to fill the reservoir to within 2" of
the top.
The power unit controller comes equipped with an automatic timer
shutting off the system 30 minutes after receiving its last command.
Because the controller "remembers" the last speed at which is
turned off, it will return to that same pace when it is turned back on.
BONDING AND GROUNDING
All of the electrical equipment that we supply is UL or CSA approved
and must be installed in accordance with local electric codes by a
licensed local electrician. Bonding and Grounding is an important
part of that process. All electrical components have bonding lugs and
should be bonded together and to the steel pool panels. A bonding
conductor shall be solid copper not smaller than 8 AWG and may be
insulated, covered or bare. If new construction is involved where rein-
forcing rods are installed in the concrete under or adjacent to the pool
this should be included in the bonding circuit. Each of the pieces of
equipment should be separately grounded.
A #8AWG bare copper wire is required for all bonding connections.
Connect this wire to your power unit and run it, with your hydraulic
hose and whip, to the front of the pool. Inside the bonding kit there
will be a machine screw and nut, a bonding lug, and a drill bit. Feed
the bonding wire through the bonding lug vertical strut at the front
of the pool. Connect the Fastlane stainless steel bond wire and the
bare copper wire to this bonding lug.
HYDRAULIC FLUID
Fill the reservoir on the Power Unit no more than 2" from the top of
the reservoir. Endless Pools, Inc. supplies a special non-petroleum
fluid created for this application and this equipment. Do not use a
substitute hydraulic fluid. Extra hydraulic fluid is provided for longer
hose runs. Any excess fluid should be retained for future use.
Make sure that all hydraulic connections are tight, then press the ON
button on the remote to turn on the Power Unit.Run for a minute or
two then check for hydraulic leaks at the Power Unit and the pool and
tighten if necessary. By pressing the OFF button on the remote you
can turn off the Power Unit. Make sure you can do this.
ASSEMBLING THE WATER QUALITY SYSTEM
WITHOUT HEATER CONTROLLER
Loosely attach the circulating pump to the power unit. The pump
will be attached to the handle of the power unit on the same side
as the hydraulic connections. Place the circulating pump on to the
power unit so that the suction of the circulating pump is facing
out. Place the pump foot clamp on the underside of the power unit
handle, aligning the holes in the pump foot clamp to the holes in
Low
Pressure
Fitting
High
Pressure
Fitting
89
2
Pool Wall
9106
Glue Pipe
From PUMP
Thru-Wall
9
Fill Cap