Datasheet

51mm
80mm
45mm
+0.6
45mm
+0.6
Logicoutputoftheinstrumentisnotelectrically
insulatedfromtheinternalcircuits. Therefore,
whenusingagroundingthermocouple,donot
connectthelogicoutputterminalstotheground.
1)Mainssupplycordsshallmeettherequirements
ofIEC60227orIEC60245.
2)Inaccordancewiththesafetyregulations,the
powersupplyswitchshallbringtheidentificationof
therelevantinstrumentanditshouldbeeasily
accessiblebytheoperator.
Note
Holding screw
0.4-0.5Nm
Equipment is protected throughout
by DOUBLE INSULATION.
1
2
1
87mm
-
-
+
+
INDUSTRIAL ELECTRONICS
EUC442-230VAC-RS
PID UNIVERSAL CONTROLLER
SN: XXXXXXXXX
6
3
2
1
7
4
8
5
OUT1 /AL2
AL1
AC 250V 2A
RESISTIVE LOAD
AC 250V 2A
RESISTIVE LOAD
230V AC +10% -20%
50/60Hz 5VA
TC
(mA inp).
Pt 100
RS-485 COM.
14
15
9
10
11
12
13
RS- 485
ANL/SSR
OUT
A
B
+
-
ENDA
-
+
INDUSTRIAL ELECTRONICS
EUC442-24VAC
PID UNIVERSAL CONTROLLER
SN: XXXXXXXXX
6
3
2
1
7
4
8
5
OUT1 /AL2
AL1
AC 250V 2A
RESISTIVE LOAD
AC 250V 2A
RESISTIVE LOAD
24V AC ±10%
50/60Hz 5VA
TC
(mA inp).
Pt 100
14
15
9
10
11
12
13
ANL/SSR
OUT
+
-
ENDA
DIMENSIONS
Depth
Forremovingthedevicefrom
thepanel:
-
1
2.
Whilepressingbothsideof
thedeviceindirection ,pushit
indirection
Connection
cables
Panel cut-out
Panel
Flush mounting
clamp
Note1)Whilepanelmounting,additionaldistancerequiredfor
connectioncablesshouldbeconsidered.
2)Panelthicknessshouldbemaximum9mm.
3)Ifthereisno100mmfreespaceatbacksideofthedevice,
itwouldbedifficulttoremoveitfromthepanel.
ENDA EUC442isintendedforinstallationincontrolpanels.Makesurethatthedeviceisusedonlyforintended
purpose. Duringaninstallation,allofthecablesthatare
connectedtothedevicemustbefreeofenergy. Thedevicemustbeprotectedagainstinadmissiblehumidity,
vibrations,severesoilingandmakesurethattheoperationtemperatureisnotexceeded. Allinputandoutputlines
thatarenotconnectedtothesupplynetworkmustbelaidoutasshieldedandtwistedcables. Thesecablesshould
notbeclosetothepowercablesorcomponents.
Theshieldingmustbegroundedontheinstrumentside.
Theinstallationandelectricalconnectionsmustbecarriedonby
aqualifiedstaffandmustbeaccordingtotherelevantlocallyapplicableregulations.
CONNECTION DIAGRAM
For J-K-T-S-R type thermocouple :
Use suitable compensation cables. Don't use
jointed cables. Pay attention to the polarities of the
thermocouple cables as shown in the figure right
are connected to the .
For resistance thermometer :
When 2 wired Pt 100 is used,
terminals 6 and 7 must be
short circuited.
NOTE :
Fuse should
be connected.
184-253V AC
50/60Hz 5VA
230V or 24V AC
Supply
switch
Cable size: 1,5mm²
Fuse
F 100 mA
250V AC
Neutral
Line
SUPPLY :
SENSOR INPUT :
10
9
TC
-
+
-
+
7
8
6
7
8
Pt100
0-20mA or
4-20mA input
-
-
+
+
7
8
E-mail:[e-mail]
Internet:www.suran-elektronik.de
Tel.: +49(0)7451/625617
Fax:+49(0)7451/6250650
SURAN Industrieelektronik
DettingerStr.9/D-72160Horba.N
Order Code -: EUC442-
2- Modbus Option
RS........RS-485Modbuscommunication
None....Don’tsupport RS-485Modbuscommunication
1- Supply Voltage
230VAC...230V AC
24VAC.....24V AC
SM...........9-30VDC/7-24V AC
110VAC...110V AC
1 2
5./5EUC442-E
48mm
58mm
UNIVERSAL CONTROLLER
ENDA
PV
SV
CSET
ASET
SET
EUC 442
CNT/AL2
AL1
SRAN/S