08M 802.
Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones. Wireless LAN devices are safe for use frequency safety standards and recommendations.
FCC Radio Frequency Exposure statement This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65 and found compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices. The radiated output power of this Wireless LAN device is far below the FCC radio frequency exposure limits.
Safety Information Your device contains a low power transmitter. When device is transmitted it sends out radio frequency (RF) signal. CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use on the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations.
TABLE OF CONTENT About This Guide...................................................................................................... 1 Purpose ................................................................................................................... 1 Overview of this User’s Guide ............................................................................... 1 Unpacking and Setup ................................................................................................ 2 Unpacking .......
ABOUT THIS GUIDE Congratulations on your purchase of this 108M Super-G Wireless LAN Access Point. This manual helps to features the innovating wireless technology that can help you build a wireless network easily! This manual contains detailed instructions in operation of this product. Please keep this manual for future reference. With a WLAN Access Point, a mobile computer can share data with another mobile computer in a wireless way.
UNPACKING AND SETUP This chapter provides unpacking and setup information for the Access Point. Unpacking Open the box of the Access Point and carefully unpack it. The box should contain the following items: One Wireless Access Point One Antenna One external power adapter One CD-Rom (User’s guide) If any item is found missing or damaged, please contact your local reseller for replacement.
HARDWARE INSTALATION LED Indicator The figure below shows the LED Indicator of the Wireless LAN Access Point. Figure 1. Font panel Power This indicator lights green when the Access Point receives power. Otherwise, it turns off. LAN (Link/ACT) The indicator lights green when the LAN port is connected to Ethernet network, the indicator blinks green while transmitting or receiving data on the Ethernet network. WLAN (ACT) The indicator blinks green when the wireless station activity to the AP.
Ethernet Ethernet uplink port with auto-sensing for connecting to either 10/100Mbps Fast Ethernet connections, connect this port to switch/hub. Reset To reset the setting back to factory default setting, press the “Reset” button 3 seconds, once you press the button, the LED of the WLAN will turn off and when the Access Point is ready, the LED will start blinking. DC Power Connect the AC Power Adapter to the AP’s power jack.
Connect to the Switch/Hub 1. Plug in one end of the RJ45 network cable to the Switch/Hub port, 2. Plug in the other end of the RJ45 network cable to the Wireless Access Point. Check the installation The control LEDs of the Access Point are clearly visible and the status of the network link can be seen instantly: 1. With the power source on, once the device is connected, the Power, LAN and WLAN LEDs of the AP will light up indicating a normal status. 2.
CONFIGURING THE WIRELESS LAN ACCESS POINT The Wireless Access Point has a Web GUI interface for the configuration. The AP can be configured through the Web Browser. A network manager can manage, control and monitor the AP from the local LAN. This section indicates how to configure the AP to enable its functions. Login Before you configure this device, note that when the AP is configured through an Ethernet connection, make sure the manager PC must be set on same the IP network.
Quick Setup with Wizard Setup wizard is provided as the part of the web configuration utility. You can simply follow the step-by-step process to get your Access Point configuration ready to run in 4 easy steps by clicking on the “Wizard” button on the function menu. The following screen will appear. Please click “Next” to continue. Figure 6. Setup Wizard Step 1: Set Password You can change the password as you like and then click “Next” to continue. Figure 7.
Step2: Set WLAN Connection Please type the name of SSID you like and select the channel. Then, click “Next” to continue. Figure 8. Setup Wizard – Set Wireless LAN Connection Step 3: Set WEP Encryption If you like to enable WEP, please click “Enabled”. Then, select the key size of WEP encryption and enter the key value in the key text box. Please click “Next” to continue. Figure 9.
Step 4: Restart The Setup wizard is now completed. The new settings will be effective after the Access Point restarted. Please click “Restart” to reboot the Access Point. If you do not want to make any changes, please click “exit” to quit without any changes. You also can go back to modify the setting by clicking “Back”. Figure 10.
Status The Status Function shows the System, Wireless Configuration and TCP/IP Configuration status and some settings of the Access Point. Figure 12. Status Firmware Version: Shows the current firmware version. LAN: Shows the Mac address, IP address (default: 192.168.1.1), Subnet Mask, Gateway Address. The current LAN traffic calculated in terms of number of packets sent and received by AP through wired connection is also displayed.
View Log: Upon clicked, the page will change to log page. The log page records every event and the time that it happens. Figure 13. View Log You may clear the entries recorded in the log by clicking the “Clear Log” button, and refresh the screen to show the latest log entries by clicking the “Refresh” button. Basic Setting This page is to configure the AP Name, SSID, Channel Number, Extended Range function, Authentication type and WEP Key setting. Figure 14.
AP Name: appoint a name for the AP. SSID: It is an ASCII string up to 32 characters used to identify a WLAN that prevents the unintentional merging of two co-located WLANs. The SSID value must be the same in all stations and AP in the extended WLAN. Wireless Channel: There are 14 channels available. The channels differ from country to country. Select the channel to be used. Extended Range: When you enable this function, AP will reduce data rate with a long distance.
IP Setting This page allows you to configure the IP and DHCP settings of the Access Point. Figure 16. IP Setting The default IP address of this access point is 192.168.1.1 with the subnet mask of 255.255.255.0. You can type in other values for IP Address, Subnet Mask and Gateway and click “Apply” button for the changes to be effective. You can also set the Access Point to obtain the IP from a DHCP server, but it is not recommended.
Advanced Setting This page contains configurations for advanced users, which the change reflects, the wireless performance and operating modes. Figure 17. Advanced Setting AP Mode: Select one of the AP operating modes for different application of Access Point. AP mode – The normal Access Point operating mode which forms a wireless ESS network with its wireless clients.
Wireless Bridge mode – A pair of APs operating under Bridge mode to act as the bridge that connect two Ethernet networks or Ethernet enabled clients together. You must make sure that the SSID and Channel is set the same as that AP you wish to connect. Remote Bridge MAC filed: key in the LAN Mac address (NOT wireless Mac address) of the AP that you wish to get connected.
CTS Mode (clear to send): None- disable CTS function. Always- Regardless of wireless environment (11b or 11g), platform will always transfer 11g packet. Auto- AP soon detected the wireless environment and decided the transmission packet, either 11b or 11g. WDS (Wireless Distribution System): Only use in AP mode. It will add client quantity at the back when you enable this function. 11g mode only: User can use 11g only when he selects “enable”.
Security This page is where you configure the security features supported by this Access Point. Figure 18. Security Password: Allow you to change the new login password. necessary steps: Here are the 1. Enter the new password in the “AP Password New:” field. 2. Enter the new password again in the “Confirm” field. 3. Click “Apply” MAC Filter: MAC Filter function controls the MAC of the network devices that are listed in this table for access authorization or denial.
Tools Four functions are provided in this page, Backup, Restore Settings, Restore default settings and Firmware Upgrade. Figure 19. Tools Backup Settings: Click on “Backup” button, which will open a FileSave Dialog box, where you get to save all the current settings and configurations to a file. Restore Settings: Click on the “Browse” button to open a FileOpen Dialog box, where you get to select the file, which you save previous settings and configurations.
TECHNICAL SPECIFICATIONS General Standards IEEE 802.11b Wireless LAN, IEEE 802.11g Wireless LAN IEEE 802.3u Fast Ethernet Signal Type: 802.11b: DSSS, 802.11g:OFDM Modulation: QPSK / BPSK / CCK / OFDM LED Indicators: Power, LAN (Link/Activity), WLAN (Activity) Frequency Range 2412 ~ 2484 MHz ISM band (channels 1 ~ 14) Frequency Band: 2.
Physical and Environmental DC inputs 5VDC /2A or higher current Temperature Operating: 0° ~ 40° C, Storage: -10° ~ 70° C Humidity Operating: 10% ~ 90%, Storage: 5% ~ 90% Dimensions 146 x 113 x 41 mm (W x H x D) without Antenna EMI: FCC Class B, CE Mark B, 20
