ENHWI-G2 802.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety of Information Technology Equipment EN 50385: 2002 Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields (110MHz - 40 GHz) - General public EN 300 328 V1.7.
Česky [Czech] Encore Electronics Inc. tímto prohlašuje, že tento ENHWI-G2 je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede Encore Electronics Inc erklærer herved, at følgende udstyr ENHWI-G2 overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
TABLE OF CONTENT ABOUT THIS GUIDE .................................................................................... 1 Purpose........................................................................................................................................ 1 Overview of this User’s Guide ................................................................................................... 1 INTRODUCTION ...........................................................................................
Security .................................................................................................................................. 38 Advanced ............................................................................................................................... 42 LAN Setting.............................................................................................................................. 43 Basic...................................................................................
ABOUT THIS GUIDE Congratulations on your purchase of this ENHWI-G2 802.11g Wireless Broadband Router. This integrated access device combines Internet gateway functions with wireless LAN and Fast Ethernet switch. It provides a complete solution for Internet surfing and office resources sharing, and it is easy to configure and operate for every users. Purpose This manual discusses how to install the ENHWI-G2 802.11g Wireless Broadband Router. Overview of this User’s Guide Introduction.
INTRODUCTION With the explosive growth of the Internet, accessing information and services at any time, day or night has become a standard requirement for most people. The era of the standalone PC is waning. Networking technology is moving out of the exclusive domain of corporations and into homes with at least two computers. This integrated access device combines Internet gateway functions with wireless LAN and Fast Ethernet switch.
Features 9 Backward Compatible with 802.
UNPACKING AND SETUP This chapter provides unpacking and setup information for the ENHWI-G2 802.11g Wireless Broadband Router Unpacking Open the box of the Wireless Broadband Router and carefully unpack it. The box should contain the following items: One ENHWI-G2 802.11g Wireless Broadband Router One 2dBi dipole antenna One CD-ROM with Users Guide One full range AC Power adapter If any item is found missing or damaged, please contact your local reseller for replacement.
HARDWARE INSTALLATION Front Panel The figure below shows the front panel of the ENHWI-G2 802.11g Wireless Broadband Router. Power LED Lights in Red when power is on. Status When this indicator blinks green it means the Wireless Broadband Router is working successful. Otherwise, hen this indicator blinks on-and-off it means the Internet Broadband Router is failing to establish internet connections. WAN (Link/ACT) When Green indicates a WAN port is being use and connected to the xDSL or Cable Modem devices.
Rear Panel The figure below shows the rear panel of the Wireless Broadband Router. Figure 1. Rear Panel Antenna Connect the supplied detachable 2 dBi Gain Antenna in the rear panel for wireless connection. LAN (1-4) Four RJ-45 10/100Mbps Auto-MDIX ports for connecting to either 10Mbps or 100Mbps Ethernet connections (auto detection). WAN One RJ-45 10/100 Mbps auto-MDIX port for Internet WAN connection. This is where the xDSL or Cable modem should be connected. DC IN Power adapter port.
Connect the Router using Wireless LAN Figure 2. Connecting Wireless LAN Router 1. Plug in one end of the RJ45 network cable to the xDSL/Cable Modem. 2. Plug in the other end of the RJ45 network cable to the Wireless Internet Broadband Router WAN port. Check the installation The control LEDs of the ENHWI-G2 802.11g Wireless Broadband Router are clearly visible and the status of the network link can be seen instantly: 1.
PC NETWORK TCP/IP SETTING The network TCP/IP settings differ based on the computer’s operating system (Win95/98/ME/NT/2000/XP) and are as follows. Windows® 95/98/ME 1. Click on the “Network neighborhood” icon found on the desktop. 2. Click the right mouse button and a context menu will be show. 3. Select “Properties” to enter the TCP/IP setting screen. 4. Select “Obtain an IP address automatically” on the “IP address” field. Figure 3 Windows 95/95/ME IP setup 5. Select “Disable DNS” in the “DNS” field.
6. Select “None” for the “Gateway address” field. Figure 5 Windows 95/98/ME Gateway setup Windows® 2000 Double click on the “My computer” icon on the desktop. When “My computer” window opens, open the “Control panel” and then open the “Network dialup connection” applet. Double click on the “Local area network connection” icon. Select “Properties” to enter the TCP/IP setting window. 1. In the “Local area network status” window, click on “Properties.” 2.
Figure 6 Windows 2000 IP and DNS setup Windows® XP Point the cursor and click the right button on the “My Network Place” icon. Select “properties” to enter the TCP/IP setting window. 1. Set “IP address” to “Obtain an IP address automatically.” 2. Set “DNS” to “Obtain DNS server address automatically.
ENHWI-G2 802.11G WIRELESS BROADBAND ROUTER CONFIGURATION First make sure that the network connections are functioning normally. This ENHWI-G2 802.11g Wireless Broadband Router can be configured using Internet Explorer 5.0 or newer web browser versions. Login to the ENHWI-G2 802.11g Wireless Broadband Router WLAN Before configuring the Wireless Broadband Router through WLAN, make sure that the SSID, Channel and the WEP is set properly.
Figure 9 Login Note: If needed to set a password, then refer to the System – Password Setting. After entering the password, the main page comes up, the screen will display the device information.
Configuration Menu When the main page appears, find the Configuration menu in the left side of the screen. Click on the setup item that you want to configure. There are six main options: WAN, Wireless, LAN, Access Control, System and Wizard as shown in the Configuration Menu screen. Figure 11 Configuration Menu Setup Wizard Setup wizard is provided as the part of the web configuration utility.
Figure 12 Setup Wizard Step 1: Set up new Password User can change the password and then click “Next” to continue.
Step 2: Choose time zone Select the time zone from the drop down list. Please click “Next” to continue. Figure 14 Setup Wizard – Set time zone Step 3: Set LAN and DHCP Server Set user’s IP address and mask. The default IP is 192.168.1.1. If user likes to enable DHCP, click “Enabled”. DHCP enabled is able to automatically assign IP addresses. Assign the range of IP addresses in the fields of “Range start” and “Range end”, click “Next” to continue.
Figure 15 Setup Wizard – Setting LAN & DHCP Server 16
Step 4: Setting the Internet connection The WLAN Router will attempt to auto detect your Internet Connection. Figure 16 Setup Wizard – WAN setup - Auto detect WAN type If the WLAN Router is unable to auto detect your Internet connection, you will need to manually select the Internet connection type: Obtain IP automatically; Fixed IP, PPPoE, PPTP, L2TP or BigPond.
Figure 17 If your ISP requires you to enter a specific host name or MAC address, please enter it in.
Fixed IP Address: Figure 19 19
If the Internet Service Providers assign a fixed IP address, choose this option and enter the assigned IP address, Subnet Mask, Gateway IP and DNS IP addresses for your Broadband Router.
Figure 21 Obtain IP Automatically: If connected to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP will provide a Password and User Name, and then the ISP uses PPPoE. Choose this option and enter the required information.
Specify IP: If connected to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP will provide a Password, User Name and a Fixed IP Address, choose this option and enter the required information.
PPTP: Figure 24 If connected to the Internet using a (PPTP) xDSL Modem, enter the your IP Address, Subnet Mask, Gateway, Server IP, PPTP Account and PPTP Password, Your Subnet Mask required by your ISP in the appropriate fields. If your ISP has provided you with a Connection ID, enter it in the Connection ID field, otherwise, leave it zero.
Figure 25 24
L2TP: Figure 26 If connected to the Internet using a (L2TP) xDSL Modem, enter the your IP Address, Subnet Mask, Gateway, Server IP, L2TP Account and L2TP Password, Your Subnet Mask required by your ISP in the appropriate fields. If your ISP has provided you with a Connection ID, enter it in the Connection ID field, otherwise, leave it zero.
Figure 27 26
BigPond: Figure 28 If your ISP is BigPond Cable, the ISP will provide a User Name, Password, Authentication Server and Login Server IP (Optional). Choose this option and enter the required information.
Step 5: Set Wireless LAN connection Click “Enable” to enable wireless LAN. If user enables the wireless LAN, type the SSID in the text box and select a communications channel. The SSID and channel must be the same as wireless devices attempting communication to the router. Figure 30 Step 6: Restart The Setup wizard is now completed. The new settings will be effective after the Wireless router restarted. Please click “Restart” to reboot the router.
Figure 31 WAN Setting This function enables users to set up the WLAN Router WAN connection, specify the IP address for the WAN, add DNS numbers, and enter the MAC address. Connection Type: Select the connection type, either DHCP client, Fixed IP or PPPoE, PPTP, L2TP or BigPond from the drop-down list.
DHCP Client or Fixed IP If user has enabled DHCP server, choose "Obtain IP automatically (DHCP client)" to have the router assign IP addresses automatically. Figure 32 WAN IP Address: Select whether user wants to specify an IP address manually, or want DHCP to obtain an IP address automatically. When Specify IP is selected, type the IP address, subnet mask, and default gateway in the text boxes. User’s ISP will provide with this information.
PPPoE with Obtain IP Automatically If connected to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP will provide a Password and User Name, and then the ISP uses PPPoE. Choose this option and enter the required information.
PPPoE with Specify IP If connected to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP will provide a Password, User Name and a Specify IP Address, choose this option and enter the required information.
PPTP/L2TP with Obtain IP Automatically If connected to the Internet using a PPTP/L2TP (Dial-up xDSL) connection, enter the your Server IP, PPTP/L2TP Account and PPTP/L2TP Password, if your ISP has provided you with a DNS IP address, enter it in the DNS field, otherwise, leave it zero.
Figure 38 L2TP Figure 37 PPTP 34
BigPond Cable If your ISP is Big Pond Cable, the ISP will provide a User Name, Password, Authentication Server and Login Server IP (Optional). Choose this option and enter the required information. Dynamic DNS: This synchronizes the DDNS server with your current Public IP address when you are online. First, you need to register your preferred DNS with the DDNS provider. Then, please selected one of DDNS server than fill the related information in the below fields: Host Name, User Name and Password.
Figure 39 Wireless setting This section enables user to set wireless communications parameters for the router's wireless LAN feature. Basic This page allow user to enable and disable the wireless LAN function, create a SSID, and select the channel for wireless communications.
Figure 40 Wireless: Enables or disables the wireless LAN function of the wireless LAN Router. SSID: Type an SSID in the text box. The SSID of any wireless device must match the SSID typed here in order for the wireless device to access the LAN and WAN via the router. Extended Range Mode: Enable and disable the wireless Extended Range enhancement. SSID Broadcast: While SSID Broadcast is enabled, all wireless clients will be able to view the WLAN Router’s SSID.
Security This function enables user to set authentication type for secure wireless communications. Open System allows public access to the router via wireless communications. Shared Key requires the user to set a WEP key to exchange data with other wireless clients that have the same WEP key. This router also supports WPA, WPA2 and WPA-PSK, WPA2-PSK. Figure 41 Security: Enable or Disable the wireless LAN security.
Figure 42 WEP: Open System and Shared Key requires the user to set a WEP key to exchange data with other wireless clients that have the same WEP key. WEP Key Format: Select the key format from the drop-down list HEX or ASCII. WEP Key Length: Select the level of encryption from the drop-down list. The WLAN Router supports, 64 and 128-bit encryption. WEP Key 1 ~ 4: Enables users to create up to 4 different WEP keys. Manually enter a set of values for each key.
WPA-PSK / WPA2-PSK Figure 43 Figure 44 If WPA or WPA2 PSK is selected, the above screen is shown. Encryption Type: Select the encryption type for TKIP or AES encryption. Passphrase: The length should be 8 characters at least.
WPA / WPA2 Figure 46 Figure 45 If WPA or WPA2 EAP is selected, the above screen is shown. Please set the length of the encryption key and the parameters for the RADIUS server. Encryption Type: Select the encryption type for TKIP or AES encryption. RADIUS Server: 1. Enter the IP address, Port used and Shared Secret by the Primary RADIUS Server. 2. Enter the IP address, Port used and Shared Secret by the Secondary RADIUS Server.
Advanced This function enables user to configure advanced wireless functions. Figure 47 Beacon Interval: Type the beacon interval in the text box. User can specify a value from 20 to 1000. The default beacon interval is 100. RTS Threshold: Type the RTS (Request-To-Send) threshold in the text box. This value stabilizes data flow. If data flow is irregular, choose values between 256 and 2346 until data flow is normalized. Fragmentation Threshold: Type the fragmentation threshold in the text box.
LAN Settings The function enables user to configure the LAN port IP address & DHCP Server. Basic This page leads to set LAN port properties, such as the host name, IP address, and subnet mask. Figure 48 Host Name: Type the host name in the text box. The host name is required by some ISPs. The default host name is "Wireless Router" IP Address: This is the IP address of the router. The default IP address is 192.168.1.1. Subnet Mask: Type the subnet mask for the router in the text box.
DHCP Settings Figure 49 DHCP Server: Enables the DHCP server to allow the router to automatically assign IP addresses to devices connecting to the LAN. DHCP is enabled by default. DHCP Server Start IP: Type an IP address to serve as the start of the IP range that DHCP will use to assign IP addresses to all LAN devices connected to the router. DHCP Server End IP: Type an IP address to serve as the end of the IP range that DHCP will use to assign IP addresses to all LAN devices connected to the router.
Routing Displays the routing details configured for this router. Static Add static IP address route. Enter the static IP address, Subnet Mask, Gateway IP address. Select from LAN or WAN and the desired Metric to the appropriate fields. Figure 50 Dynamic Add a dynamic IP address route. Select to “Enable” or “Disable” NAT. Select the desired “Transmit” and “Receive” from “Disable, RIP1 and RIP2”.
Figure 51 Routing Table Lists IP address of the Internet destinations commonly accessed by your network.
Access Control Settings This access control enables you to define access restrictions, set up protocol and IP filters, create virtual servers, define access for special applications such as games, and set firewall rules. Filter Using filter to deny or allow the users to access. Five types of filters to select: MAC, IP Filter, URL blocking, Domain blocking and Protocol filter.
MAC Table: Use this section to create a user profile which Internet access is denied or allowed. The user profiles are listed in the table at the bottom of the page. (Note: Click anywhere in the item. Once the line is selected, the fields automatically load the item's parameters, which you can edit.) Name: Type the name of the user to be permitted/denied access. MAC Address: Type the MAC address of the user's network interface. Add: Click to add the user to the list at the bottom of the page.
Enable: Click to enable or disable the IP address filter function. Range Start: Type the minimum address for the IP range. IP addresses falling between this value and the Range End are not allowed to access the Internet. Range End: Type the minimum address for the IP range. IP addresses falling between this value and the Range Start are not allowed to access the Internet. Add: Click to add the IP range to the table at the bottom of the screen.
URL Blocking You could enable URL blocking to deny the users from accessing the specified URL or internet address. Add the desired URL or internet address to the text box. Figure 55 Enable / Disable: Enable or Disable the URL blocking function. Add: Click to add the specified URL to the URL blocked listing. Delete: Remove a URL from the URL Blocked list. Select a URL from the blocked list then click Delete.
Domain Blocking You could specify the domains that allow users to access or deny by clicking one of the two items. Also, add the specified domains in the text box. Figure 56 Disable: Disable the Domain Blocking function. Allow: Allow users to access all domains except “Blocking Domains”. Deny: Deny users to access all domains except “Permitted Domains”. Blocked/Permitted Domains: List domains you will Blocked or Permitted. Apply: Click to add domain to the Blocked/Permitted Domains list.
Protocol Filters This protocol filter enables you to allow and deny access based upon a communications protocol list you create. The protocol filter profiles are listed in the table at the bottom of the page. Note: When selecting items in the table at the bottom, click anywhere in the item. The line is selected, and the fields automatically load the item's parameters, which you can edit. Figure 57 Enable: Click to enable or disable the Protocol filter. Name: Type the name of the user to be denied access.
Clear: Click to erase all fields and enter new information. Virtual Server The virtual server function enables users to create a virtual server via the WLAN Router. If the WLAN Router is set as a virtual server, remote users requesting Web or FTP services through the WAN are directed to local servers in the LAN. The WLAN Router redirects the request via the protocol and port numbers to the correct LAN server. The Virtual Sever profiles are listed in the table at the bottom of the page.
Add: Click to add the virtual server to the table at the bottom of the screen. Update: Click to update information for the virtual server if the user has selected a listed item and has made changes. Delete: Select a listed item and click “Delete” to remove the item from the list. Clear: Click to erase all fields and enter new information. Special AP The special AP function enables users to specify special applications, such as games which require multiple connections that are blocked by NAT.
z Port Range: Type the port range that can be used to access the application in the text boxes. Incoming: Defines which incoming communications users are permitted to connect with. z Protocol: Select the protocol TCP or UDP that can be used by the incoming communication, the “*” is meaning to both of TCP and UDP protocols. z Port: Type the port number that can be used for the incoming communication. Add: Click to add the special application profile to the table at the bottom of the screen.
Apply: Click to save the settings. Firewall Rule The firewall rule function enables users to set up the firewall. The WLAN Router provides basic firewall functions, by filtering all the packets that enter the WLAN Router using a set of rules. The rules are listed in sequential order--the lower the rule number, the higher the priority the rule has. Figure 61 Enable: Click to enable or disable the firewall rule profile. Name: Type a descriptive name for the firewall rule profile.
● Port Range: Select the port range. Add: Click to add the rule profile to the table at the bottom of the screen. Update: Click to update information for the rule if the user has selected a listed item and has made changes. Delete: Select a listed item and click “Delete” to remove the item from the list. Clear: Click to erase all fields and enter new information. Priority Up: Select a rule from the list and click “Priority Up” to increase the priority of the rule.
Time This function enables users to set the time and date for the WLAN Router's real-time clock, select properly time zone, and enable or disable daylight saving. Figure 63 Local Time: Displays the local time and date. Time Zone: Select the time zone from the drop-down list. Synchronize the clock with NTP Server: Enable or disable the WLAN Router automatically adjust the system time from NTP Server.
Device Information This function enables users to view the WLAN Router’s WAN, Wireless, LAN and System configurations. Figure 64 WAN: This section displays the WAN interface configuration including the MAC address, Connection status, DHCP client status, IP address, Subnet mask, Default gateway, and DNS. Wireless: This section displays the wireless configuration information, including the MAC address, the Connection status, SSID, Channel and Authentication type.
Log This function enables users to view a running log of Router system statistics, events, and activities. The log displays up to 200 entries. Older entries are overwritten by new entries.
Log Setting This function enables users to set Router Log parameters. Figure 66 SMTP Server: Type-in your SMTP server address here. Send to: Type-in an email address for the log to be sent to. Click “Email Log Now” to immediately send the current log. SMTP Authentication: Select Enabled if the SMTP server need authentication, fill in your account username and password in SMTP Account field and SMTP Password field. SMTP Account: If the SMTP Authentication enabled, fill in the SMTP account name here.
Statistic This function displays a table that shows the rate of packet transmission via the WLAN Router’s LAN, WAN and Wireless ports (in bytes per second). Figure 67 Click “Reset” to erase all statistics and begin logging statistics again. Restart Click “Restart” to restart the system in the event the system is not performing correctly.
Figure 68 Firmware This function enables users to keep the WLAN Router firmware up to date.
Figure 69 Please follow the below instructions: Download the latest firmware from the manufacturer's Web site, and save it to disk. Click “Browse” and go to the location of the downloaded firmware file. Select the file and click “Upgrade” to update the firmware to the latest release.
Configuration This function enables users to save settings as a profile and load profiles for different circumstances. User can also load the factory default settings, and run a setup wizard to configure the WLAN Router and Router interface. Figure 70 UPnP This function enables users to enable or disable the UPnP function on the WLAN Router.
Figure 71 UPnP: Select to enable or disable the UPnP function on the WLAN Router. Ping Test The ping test enables users to determine whether an IP address or host is present on the Internet. Type the host name or IP address in the text box and click Ping button to start the Ping test.
Figure 72 67
Remote Management This function enables users to set up remote management. Using remote management, the WLAN Router can be configured through the WAN via a Web browser. A user name and password are required to perform remote management. Figure 73 HTTP: Enable / Disable users HTTP access for remote management.
TECHNICAL SPECIFICATIONS General Standards Protocol Radio Technology Data Transfer Rate Topology Receiver Sensitivity TX Power Network Cables Frequency Range Modulation Schemes Security Channels Number of Ports IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.11g; IEEE 802.11b CSMA/CD 802.11b: Direct Sequence Spread Spectrum (DSSS) 802.11g: Orthogonal Frequency Division Multiplexing (OFDM) 802.11b: 1, 2, 5.5, 11Mbps (auto sense) 802.
