ENDSL-A2+WIGX2 ADSL2+ Modem With Four Port Ethernet and 802.
FCC Warning ENDSL-A2+WIGX2 has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication.
Copyright 2007 All Rights Reserved. No part of this document can be copied or reproduced in any form without written consent from Encore Electronics Inc. Trademarks: All trade names and trademarks are the properties of their respective companies. Revision History Revision History V1.
Contents 1. Introduction................................................................................. 6 1.1 Introduction ......................................................................................... 6 1.2 Product Features................................................................................. 6 2. Hardware Installation................................................................ 10 2.1 System Requirements.......................................................................
6.2.4 DHCP Relay ............................................................................. 46 6.2.5 DNS Relay ................................................................................ 47 6.3 Wireless ............................................................................................. 48 6.3.1 Access Point Settings............................................................. 48 6.3.2 Multiple SSIDs Settings .......................................................... 49 6.3.
11. Troubleshooting...................................................................... 81 11.1 Using LEDs to Diagnose Problems................................................ 81 11.1.1 Power LED ............................................................................. 81 11.1.2 LAN LED................................................................................. 81 11.1.3 ADSL LED............................................................................... 81 11.
1. Introduction 1.1 Introduction This full rate ENDLS-A2+WIGX2 is an all-in-one gateway for Home and SOHO applications. This gateway are with full-featured ADSL router that provides high-speed Internet access, 4-port Ethernet switch direct connections to individual PCs or local area network with 10/100 Base-T Ethernet and a 54Mbps IEEE802.11g wireless connectivity. ENDLS-A2+WIGX2 uses advanced ADSL chipset solution with complete set of industry standard features for high-speed Internet access.
is compliant with the following standards. z ANSI T1.413 issue 2 z ITU-T G.992.1 (G.dmt) z ITU-T G.992.2 (G.lite) z G.994.1 (G.hs, Multimode) z ITU-T G.992.3 (ADSL2 G.dmt.bis) z ITU-T G.992.4 (ADSL2 G.lite.bis) z ITU-T G.992.5 (ADSL2+; Annex A, B, I, J, L & M) z Reach Extended ADSL (RE ADSL) Quick Setup Wizard Support Quick Setup Wizard Web GUI to configure the ENDLS-A2+WIGX2 easily and quickly.
With Dynamic DNS support, you can have a static hostname alias for a dynamic IP address, allowing the host to be more easily accessible from various locations on the Internet. You must register for this service with a Dynamic DNS client. DHCP Support DHCP (Dynamic Host Configuration Protocol) allows individual clients to obtain TCP/IP configuration at start-up from a centralized DHCP server. The ADSL router has built-in DHCP server capability enabled by default.
z Dynamic date rate scaling at 11, 5.5, 2 and 1Mbps for IEEE802.11b z Supports Quality of Service (QoS), 802.
2. Hardware Installation 2.1 System Requirements z Pentium III 266 MHz processor or higher z 128 MB RAM minimum z 20 MB of free disk space minimum z RJ45 Ethernet Port 2.2 Package Contents z ENDLS-A2+WIGX2 modem z RJ-45 Ethernet cable z RJ-11 Phone cable z Power Adapter z Quick Installation Guide z One External Antenna (for detachable model) 2.3 Front Panel Indicators and Description Front panel of the ENDLS-A2+WIGX2 router has LED indicators to display router’s operating status.
2.4 Back Panel PWR Connect with power adapter ON/OFF Power switch button LINE Connect with phone cable 4 Connect with Ethernet Cable to Switch Hub or PC 3 Connect with Ethernet Cable to Switch Hub or PC 2 Connect with Ethernet Cable to Switch Hub or PC 1 Connect with Ethernet Cable to Switch Hub or PC DEFAULT Reset button 2.
3. Connecting ENDLS-A2+WIGX2 via Ethernet Your router can be managed from anywhere with the embedded Web configuration using a Web browser, such as Microsoft Internet Explorer or Netscape Navigator. Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later versions with JavaScript enabled should be used. 3.1 Setup ENDLS-A2+WIGX2 via Ethernet Cable If there is an available LAN card present on your PC, you just simply connect ADSL router and PC through the Ethernet cable.
Option1: Get an IP from Router Automatically Select the IP Address tab. In this page, click Obtain an IP address automatically radio button.
2) Then, select DNS Configuration tab and select Disable DNS then click OK to finish the configuration. Option2: Configure IP Manually 1) At IP Address tab, select Specify an IP address, set default IP address for the Router is 192.168.1.1, so use 192.168.1.X (X is a number between 2 to 254) for IP Address field and 255.255.255.0 for Subnet Mask field.
2) Select Gateway tab and add default Router IP Address “192.168.1.1” in the New gateway field and click Add. Under DNS Configuration tab, select Enable DNS and add DNS values (192.168.1.1) in DNS Server Search Order field then click Add.
For Windows® 2000 Step 1: (a) Right-click My Network Places and select Properties in the main window screen (b) Or, go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections.
Step 3: Select Internet Protocol (TCP/IP) then click Properties: Configure IP Automatically: Step 4: Select Obtain an IP address automatically and Obtain DNS server address automatically then click OK to complete IP configuring process.
Configure IP Manually: Step 4: Select Use the following IP address and Use the following DNS server addresses. IP address: Fill in IP address 192.168.1.x (x is a number between 2 to 254). Subnet mask: Default value is 255.255.255.0. Default gateway: Default value is 192.168.1.1. Preferred DNS server: Fill in preferred DNS server IP address. Alternate DNS server: Fill in alternate DNS server IP address. For Windows® XP Step 1: Click Start then select Control Panel.
Step 2: Double-click Network Connections icon.
Step 4: Select Internet Protocol (TCP/IP) then click Properties: Configure IP address Automatically: Step 5: Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK to finish the configuration.
Configure IP Address Manually: Step 5: Select Use the following IP address and Use the following DNS server addresses. IP address: Fill in IP address 192.168.1.x (x is a number between 2 to 254). Subnet mask: Default value is 255.255.255.0. Default gateway: Default value is 192.168.1.1. Preferred DNS server: Fill in preferred DNS server IP address. Alternate DNS server: Fill in alternate DNS server IP address.
For Windows Vista™ Step 1: Click Start then select Control Panel (in the Classic View). Step 2: Double-click Network and Sharing Center icon.
Step 3: Select “Manage Network connections”.
Step 5: Select Internet Protocol (TCP/IP) then click Properties: Configure IP address automatically: Step 6: Select Obtain an IP address automatically and Obtain DNS server address 24
automatically. Click OK to finish the configuration. Configure IP Address Manually: Step 7: Select Use the following IP address and Use the following DNS server addresses. IP address: Fill in IP address 192.168.1.x (x is a number between 2 to 254). Subnet mask: Default value is 255.255.255.0. Default gateway: Default value is 192.168.1.1. Preferred DNS server: Fill in preferred DNS server IP address.
Alternate DNS server: Fill in alternate DNS server IP address. You can use ping command under DOS prompt to check if you have setup TCP/IP protocol correctly and if your computer has successfully connected to this router. 2) Type ping 192.168.1.1 under DOS prompt and the following messages will appear: Pinging 192.168.1.1 with 32 bytes of data: Reply from 192.168.1.1: bytes=32 times<2ms TTL=64 Reply from 192.168.1.1: bytes=32 times<1ms TTL=64 Reply from 192.168.1.
4.2 Navigating the Web Configuration Steps to navigate the Web configuration from the Site Map are summarized as below.
Steps to navigate the Web configuration from the Site Map are summarized below. ¾ Click on Quick Start to begin a wizard that helps to configure your router. ¾ Click on Interface Setup to configure Internet and LAN functions. ¾ Click on Advanced Setup to configure advanced features. ¾ Click on Access Management to manage Internet access options.
Click Quick Start to guide you to configure the device to connect your ISP and have Internet access within minutes. This Quick Start will guide you step by step to configure the password, time zone, and WAN settings of you device. This Wizard is a helpful guide for first time uses to the device. NOTE: It is a strong recommendation that using Quick Start to configure your ADSL settings. Click on the RUN WIZARD button to start the Quick Start wizard.
. The Quick Start Setup Wizard includes four quick steps: 1) Set your new password. 2) Choose your time zone. 3) Set your Internet connection. 4) Re-start your ADSL router. Please follow the quick start step by step to configure the device. Note: If your ISP doesn’t provide DNS, after you complete Quick Start configuration, please go to Interface Setup Æ Internet to configure your DNS settings. Click on NEXT to continue, or on EXIT to exit the wizard without saving.
5.1 Setting a New Password This screen helps you set a new password, replacing the default password. The following table describes the labels in this screen. LABEL DESCRIPTION New Password Enter the password you wish to use here Confirmed Password Enter the password again to confirm Click on BACK to return to the previous screen, on NEXT to continue, or on EXIT to exit the wizard without saving. 5.2 Choose your Time Zone This screen helps you set the time zone for your ENDLS-A2+WIG.
5.3 Set your Internet Connection This screen helps you select, then configure, your ISP connection type. Select the Internet connection type you use to connect to your ISP. Click on BACK to return to the previous screen, on NEXT to continue, or on EXIT to exit the wizard. The following screen will vary depending on which connection type you chose. Each screen is explained below: 5.3.
The following table describes the labels in this screen. LABEL DESCRIPTION VPI Enter the VPI here. VPI can range from 0 to 255. VCI Enter the VCI here. VCI can range from 1 to 65535. Connection Type Select your connection type from the dropdown list. Your ISP should provide the above information. Click on BACK to return to the previous screen, on NEXT to continue, or on EXIT to exit the wizard without saving. 5.3.
5.3.3 Configuring PPPoE PPPoE provides access control and billing functionality in a manner similar to dial-up services using PPP. The router bridges a PPP session over Ethernet (PPP over Ethernet, RFC 2516) from your computer to an ATM Permanent Virtual Circuit (PVC) that connects to the ADSL Access Concentrator, where the PPP session terminates. Single PVC can support any number of PPP sessions from your LAN. The following table describes the labels in this screen.
The following table describes the labels in this screen. LABEL DESCRIPTION Username Enter your username here. Password Enter your password here. VPI Enter the VPI here. VPI can range from 0 to 255. VCI Enter the VCI here. VCI can range from 1 to 65535. Connection Type Select your connection type from the dropdown list. Your ISP should provide the above information. Note that you must enter the user name exactly as your ISP assigned it.
The following table describes the labels in this screen. LABEL DESCRIPTION VPI Enter the VPI here. VPI can range from 0 to 255. VCI Enter the VCI here. VCI can range from 32 to 65535. Connection Type Select your connection type from the dropdown list. Your ISP should provide the above information. Click on BACK to return to the previous screen, on NEXT to continue, or on EXIT to exit the wizard without saving. 5.3.
5.4 Finishing the Wizard The Quick Start wizard now has all the information it needs. Click on BACK to make changes or correct mistakes. Click on NEXT to save the current settings. Click on EXIT to exit the wizard without saving. Your changes have been saved. Click CLOSE. The Quick Start wizard window will close.
6. Interface Setup The physical connections determine whether the router ports are local area network (LAN) ports or wide area network (WAN) ports. There are two kinds of IP networks. The local, private kind is the LAN network; the global, public kind is the WAN network. The following illustration shows the relationship between the router and the two different networks. A LAN is a shared communication system to which many computers are attached.
6.1.1 ATM VC & QoS ATM settings are used to connect to your ISP. Your ISP provides VPI, VCI, settings to you. In this Device, you can totally setup 8 PVCs on different encapsulations if you apply 8 different virtual circuits from your ISP. You need to activate the VC to take effect. For PVCs management, you can use ATM QOS to setup each PVC traffic line’s priority. Virtual Circuit: Select the VC number you want to setup. VPI: Virtual Path Identifier. The valid range for the VPI is 0 to 255.
time, more cells (up to the MBS) can be sent at the PCR again. CBR is for connections that support constant rates of data transfer. The only parameter you need to worry about in CBR is PCR. UBR is for connections that have variable traffic. The only parameter you need to worry about in UBR is PCR. rtVBR is for connections that, while having variable traffic, require precise timing between traffic source and destination. PCR, SCR and MBS must all be set for rtVBR.
(2) Static IP Address Select this option to set static IP information. You will need to enter in the encapsulation type (1483 Bridged IP LLC, 1483 Bridged IP VC-Mux, 1483 Routed IP LLC (IPoA), 1483 Routed IP VC-Mux), IP address, subnet mask, and gateway address provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which is 4 IP octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
LABEL DESCRIPTION Username Enter your username for your PPPoE/PPPoA connection. Password Enter your password for your PPPoE/PPPoA connection. Encapsulation Select your encapsulation type from the dropdown list. Bridge Interface Select whether the Interface will be Activated or Deactivated. Connection Select whether your connection is always on or if it connects on demand. If on demand, specify how many minutes the connection may be idle before it disconnects.
Connection Setting: For PPPoE/PPPoA connection, you can select Always on or Connect on-demand. Connect on demand is dependent on the traffic. If there is no traffic (or Idle) for a pre-specified period of time, the connection will tear down automatically. And once there is traffic send or receive, the connection will be automatically on. IP Address: For PPPoE/PPPoA connection, you need to specify the public IP address for this ADSL Router.
The following table describes the labels in this screen. LABEL Encapsulation DESCRIPTION Select your encapsulation type from the dropdown list. 6.2 LAN There are the IP settings of the LAN Interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is provided to your internal network and cannot be seen on the Internet. 6.2.
Dynamic Route: Select the Dynamic Route from RIP1, RIP2-B, and RIP2-M. Please refer to InternetÆ Dynamic Route. The only difference is the interface. IGMP Snoop: You can disabled and enabled IGMP Snoop function. 6.2.2 Explaining RIP Setup Routing Information Protocol (RIP) allows a router to exchange routing information with other routers. The RIP Direction field controls how RIP packets are allowed to enter and leave the router.
LABEL Starting IP Address DESCRIPTION Enter the starting IP address you wish to use as the DHCP server's IP assignment. IP Pool Count Enter the maximum user pool size you wish to allow. Lease Time Enter the amount of time you wish to lease out a given IP address. DNS Relay Select the DNS relay option you wish to use from the dropdown list. Primary DNS Server Enter the primary DNS server IP address you wish to use. For user discovered DNS only.
6.2.5 DNS Relay The DNS Configuration allows the user to set the configuration of DNS. DNS Rely Selection: If user wants to disable this feature, he just needs to set both Primary & Secondary DNS to 0.0.0.0. Using DNS relay, users can setup DNS server IP to 192.168.1.1 on their computer. If not, device will perform as NO DNS relay. If you don’t want to use the DNS Relay option, set the DNS relay to “Use User Discovered DNS Server Only” and set both Primary and Secondary DNS Servers to “0.0.0.0”.
6.3 Wireless 6.3.1 Access Point Settings Beacon Interval: The Beacon Interval value indicates the frequency interval of the beacon. Enter a value between 20 and 1000. A beacon is a packet broadcast by the Router to synchronize the wireless network. RTS/CTS Threshold: The RTS (Request To Send) threshold (number of bytes) for enabling RTS/CTS handshake. Data with its frame size larger than this value will perform the RTS/CTS handshake.
handshake. Enter a value between 0 and 2432. Fragment Threshold: The threshold (number of bytes) for the fragmentation boundary for directed messages. It is the maximum data fragment size that can be sent. Enter a value between 256 and 2432. DTIM: This value is between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM). 6.3.2 Multiple SSIDs Settings SSID: The SSID is a unique name to identify the ADSL Router in the Wireless LAN.
Action: Select Deny Association to block access to the router, MAC addresses not listed will be allowed to access the router. Select Allow Association to permit access to the router, MAC addresses not lusted will be denied access to the router. 7 Advanced Setup 7.1 Firewall User can enable or disable firewall feature of the ADSL router in the page. Firewall: Select this option can automatically detect and block Denial of Service (DoS) attacts, such as Ping of Death, SYN Flood, Port Scan and Land Attack.
[Static Route] Select this option to set Static Routing information. Destination IP Address: This parameter specifies the IP network address of the final destination of packets routed by this rule. IP Subnet Mask: Enter the subnet mask for this destination. Gateway IP Address: Enter the IP address of the gateway. A gateway does the actual forwarding of the packets. Enter the gateway’s IP address in the field or select which PVC you wish to act as a gateway.
Announced in RIP: This parameter determines if the ADSL router includes the router to this remote node in its RIP broadcasts. If you choose Yes, the router in this remote node will be propagated to other hosts through RIP broadcasts. If you choose No, this route is kept private and is not included in the RIP broadcasts.
Note: For VCs with single IP, they share the same DMZ & Virtual servers; for VCs with multiple IPs, each VC cab set DMZ and Virtual servers. Furthermore, for VCs with multiple IPs, they can define the Address Mapping rules; for VCs with single IP, since they have only one IP, there is no need to individually define the Address Mapping rule. 7.3.
Each packet has two addresses – a source address and a destination address. For outgoing packets, the ILA is the source address on the LAN, and the IGA is the source address on the WAN. For incoming packets, the ILA is the destination address on the LAN, and the IGA is the destination address on the WAN. NAT maps private (local) IP addresses to globally unique ones required for communication with hosts on other networks.
7.3.4 NAT Mapping Types NAT supports five types of IP/port mapping. They are: a. One-to-One: In One-to-One mode, the TC3162 EVM maps one local IP address to one global IP address. b. Many-to-One: In Many-to-One mode, the TC3162 EVM maps multiple local IP addresses to one global IP address. c. Many-to-Many Overload: In Many-to-Many Overload mode, the TC3162 EVM maps multiple local IP addresses to shared global IP addresses. d.
ILA4 IGA2 … Many-to-Many No Overload ILA1 IGA1 ILA2 IGA2 ILA3 IGA3 … Server Server 1 IP IGA1 Server 2 IP IGA1 Server 3 IP IGA1 7.3.5 DMZ A DMZ (de-militarized zone) is a host between a private local network and the outside public network. It prevents outside users from getting direct access to s server that has company data. Users of the public network outside the company can access only the DMZ host. DMZ: Toggle the DMZ function Enabled or Disabled.
Rule Index: The Virtual server rule index for this VC. You can specify up to 10 rules. All the VCs with single IP will use the same Virtual Server rules. Start & End port number: Enter the specific Start and End Port number you want to forward. If it is one port only, you can enter the End port number the same as Start port number. For example, set the FTP Virtual server, you can set the start and end port number to 21. Local IP Address: Enter the IP Address for the Virtual Server in LAN side.
7.3.7 IP Address Mapping The IP Address Mapping is for those VCs that with multiple IPs. The IP Address Mapping rule is per-VC based. (only for Multiple IPs’ VCs). Rule Index: The Virtual server rule index for this VC. You can specify up to 10 rules. All the VCs with single IP will use the same Virtual Server rules. Rule Type: There are 4 types of One-to-One, Many-to-One, Many-to-Many Overload, and Many-to Many No-Overload. Local Start & End IP: Enter the local IP address you plan to map to.
7.4 QoS QoS (Quality of Service). This option will provide better service of selected network traffic over various technologies. Deploying QoS management to guarantee that all application receive the service levels required and sufficient bandwidth to meet performance expectations is indeed one important aspect of modem enterprise network.
7.5 VLAN Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments.
optimization. (1) Port-Based VLAN: each physical switch port is configured with an access list specifying membership in a set of VLANs. (2) ATM VLAN-using LAN Emulation(LANE) protocol to map Ethernet packets into ATM cells and deliver then to their destination by converting an Ethernet MAC address into an ATM address. The key for the IEEE 802.1Q to perform the above functions is in its tags. 802.1Q-compliant switch ports can be configure to transmit tagged or untagged frames.
7.6 ADSL Select this option to set ADSL Mode and ADSL Type information. ADSL Mode: Select which mode your ADSL connection uses from the dropdown list. The option has Auto Sync-up, ADSL2+, ADSL2, G.DMT, T1.413, G.LITE ADSL Type: Select the ADSL type you use from the dropdown list. ANNEX A, ANNEX I, ANNEX A/L, ANNEX M, ANNEX A/I/J/L/M When you are done making changes, click on SAVE to save your changes. 8. Access Management 8.1 ACL Go to Access Management Æ ACL to enable remote management.
on application. You may use telnet or Web to remotely manage the ADSL Router. User just needs to enable Telnet or Web and give it an IP address that wants to access the ADSL Router. The default IP 0.0.0.0 allows any client to use this service to remotely manage the ADSL Router. ACL: There has Activated & Deactivated option. The default setting is Deactivated which means all IP can access via router. If you choose Activated, you only can access via router by listed IP addresses.
4. Choose the Application which you want to access for this ACL Rule index. 5. Select the Interface you want to access from. 6. After all settings are ready, click SAVE and continue next ACL Rule Index setting. [Note] 1. You must set one ACL index to access your router via LAN interface. If you don’t, your router cannot access other listed IP Address. (Refer to Index 1). 2. Remember! Once you active your ACL function, you only can access via router by listed Secure IP Address. 8.
IP Filter Set Index: The IP Filter Set Index from 1 to 12 and each index can set up to 6 IP Filter. Interface: Choices from PVC0 to PVC7 and LAN. Direction: Choices are Both, Incoming and Outgoing. Select which direction of data flow you wish to apply the filters to. Note that Incoming and Outgoing are from the point of view of your router, relative to the interface you select. For WAN, data coming from outside your system is considered Incoming and data leaving your system is Outgoing.
Active: Toggle this rule index on or off with Yes or No, respectively. Source IP Address: Enter the source IP address you wish to deny access to your system. Subnet Mask: Enter the subnet mask of the source IP address. Port Number: Enter the port number of the source IP address. Note that 0 means all that ports are allowed. Destination IP Address: Enter the destination IP address that you wish to deny access to your system.
67
8.3 SNMP The Simple Network Management Protocol (SNMP) is used for exchanging information between network devices. It enables a host computer to access configuration, performance, and other system data that resides in a database on the modem. The host computer is called a management station and the modem is called an SNMP agent. The data that can be accessed via SNMP is stored in a Management Information Database (MIB) on the modem.
UPnP (Universal Plug and Play): You can choose “Activated” or “Deactivated” option from this session. Auto-Configured (by UPnP Application): UPnP network devices can automatically configure network addressing, announce their presence in the network to other UPnP devices and enable exchange of simple product and service descriptions.
Dynamic DNS: Choose the option for Activated or Deactivated DDNS. Service Provider: The default Dynamic DNS service provider is www.dyndns.org. My Host Name: Type the domain name assigned to your ADSL by your Dynamic DNS provider. E-mail Address: Type your e-mail address. Username: Type your user name. Password: Type the password assigned to you. Wildcard support: Select Yes or No to turn on DYNDNS Wildcard. DYNDNS Wildcard --> Enabling the wildcard feature for your host causes *.yourhost.dyndns.
number of different Internet access possibilities grew as well (e.g. modems, routers, gateways, Set-top box, paddles, VoIP-phones). At the same time the configuration of this equipment became more complicated -- too complicated for the end-users. For this reason the TR-069 standard was developed. It provides the possibility of auto configuration of these access types. The technical specifications are managed and published by the DSL Forum.
9. Maintenance 9.1 Administration There is only one account that can access Web-Management interface-Administration. Admin has read/write access privilege. In this web page, you can set new password for admin. New Password: Type the new password in this field. Confirm Password: Type the new password again in this field. Note: If you ever forget the password to log in, you may press the RESET button up to 6 second to restore the factory default settings.
Current Date/Time: This field displays an updated Date and Time when you reenter this menu. [Time Synchronization] Synchronize time with: You can choose “NTP Server automatically”, “PC’s Clock”, or “Manually” to coordinate the time. Time Zone: Choose the Time Zone of your location. This will set the time difference between your time zone and Greenwich Mean Time (GMT). Daylight Saving: Choose “Enabled” or “Disabled” to use daylight savings time.
9.3 Firmware You can upgrade the firmware of the router in this page. Make sure the firmware you want to use is on the local hard drive of the computer. Click on Browse to browse the local had drive and locate the firmware to be used for the update. Then press UPGRADE to upload new Firmware. It might take several minutes, don’t power off it during upgrading. Device will restart after the upgrade!! After a success upload, the system automatically restarts. Please wait for the device to finish restarting.
9.5 Diagnostic The Diagnostic Test page shows the test results for the connectivity of the physical layer and protocol layer for LAN & WAN sides. Select which PVC you wish to test from the dropdown list. The router will automatically run diagnostic tests on that circuit. A green PASS means that the given test was passed, a red FAIL means that the test was failed and a green SKIPPED means that the test was skipped. Note: 1) User ONLY can view PVC0’s Diagnostic Test connection.
10. Status 10.1 Device Info The Device Info screen is a tool that you use to monitor your ADSL Router. It shows the Firmware Version, WAN, LAN, and MAC address information. Note that these fields are read-only and are not meant for diagnostic purposes. Except the Virtual Circuit, click the drop-down list and select the name of the Virtual Circuit on which the system status is to be shown. [Device Information] Firmware Version: This filed displays current firmware version.
[LAN] IP Address: The LAN port IP address Subnet Mask: The LAN port IP subnet mask. DHCP Server: The status of DHCP Server (Enabled or Disabled) [WAN] Virtual Circuit: Click the drop-down list and select the name of the Virtual Circuit on which the system status is to be shown. Status: Connected or Not Connected Connection Type: The WAN Connection Type. IP Address: The WAN port IP address Subnet Address: The WAN port IP subnet mask. Default Gateway: The IP address of the default gateway, if applicable.
10.2 System Log The System Log displays data generated or acquired by routine system communication with other devices, such as the results of negotiations with the ISP's computers for DNS and gateway IP addresses. The device keeps a running log of events and activities occurring on the Router. You can click Save Log to display a Windows File Download dialog box that enables opening or saving the contents of the log to your PC. To remove all entries from the list, click Clear Log.
10.3 Statistics The ADSL Router keeps statistic of traffic that passes through it. You are able to view the amount of packets that passes through the Router on both the WAN port & the LAN port. The traffic counter will reset if the device is rebooted. You can select Ethernet/ADSL/WLAN to view the statistics report of LAN/WAN. [Ethernet] The Ethernet screen gives you information on how much data your router has transmitted and received across the Ethernet connection. Click on REFRESH to update the screen.
[ADSL] The ADSL screen gives you information about how much data your router has transmitted or received across the ADSL connection. Click on REFRESH to update the screen. [WLAN] The WLAN screen gives you information about how much data your router has transmitted or received across the ADSL connection. Click on REFRESH to update the screen.
11. Troubleshooting If the router is not function properly, first check this session for simple troubleshooting before contacting your Internet service provider (ISP) for support. 11.1 Using LEDs to Diagnose Problems The LEDs are useful aides for finding possible problem causes. 11.1.1 Power LED The PWR LED on the front panel does not light up. STEPS 1 CORRECTIVE ACTION Make sure that the power adaptor is connected to the router and plugged in to an appropriate power source.
11.2 Problems with the Web Interface I cannot access the web Interface. STEPS 1 CORRECTIVE ACTION Make sure you are using the correct IP address of the router. Check the IP address of the router. 2 Make sure that there is not a console session running. 3 Check that you have enabled web service access. If you have configured a secured client IP address, your computer’s IP address must match it. Refer to the chapter on remote management for details.
4 It is highly recommended to change the default username and password. Make sure you store the username and password in a save place. 11.4 Problems with LAN Interface I cannot access the router from the LAN or ping any computer on the LAN. STEPS CORRECTIVE ACTION 1 Check the Ethernet LEDs on the front panel. A LAN LED should be on for a port that has a PC connected. If it is off, check the cables between your router and the PC. Make sure you have uninstalled any software firewall for troubleshooting.
2 The username and password apply to PPPoE and PPoA encapsulation only. Make sure that you have entered the correct Service Type, User Name and Password (be sure to use the correct casing). 11.6 Problems with the Internet Access I cannot access the Internet. STEPS CORRECTIVE ACTION 1 Make sure the router is turned on and connected to the network. 2 If the ADSL LED is off, refer to Section 11.1.3 (Page 71). 3 Verify your WAN settings. 4 Make sure you entered the correct user name and password.
