E3 PROFESSIONAL REMOTE ALARM SYSTEM INSTALLATION MANUAL This unit is designed for professional installation only and must be installed by an Encore authorized dealer. Please register this product at www.encoreautomotivesystems.com. E3 IN REV.
Precautions: Please read carefully This Remote Starter with Alarm and Keyless Entry System has been designed to be installed BY PROFESSIONAL INSTALLERS on fuel-injected vehicles with an automatic transmission ONLY. Never install this remote starter on a manual transmission vehicle. This system must be installed and wired through a safety switch so it will not start in any forward or reverse gear.
INSTALLATION DIAGRAM E3 IN REV.
Main Power Connector RED / WHITE: PARKING LIGHT RELAY INPUT WHITE: PARKING LIGHT OUTPUT BLACK : MAIN SYSTEMS GROUND BROWN : POSITIVE SIREN OUTPUT RED : FUSED 12 VOLT (+) BATTERY POWER 3 PIN, DOOR LOCK CONNECTOR 1. Blue Wire ( - ) Unlock Pulse (+) Lock Pulse 3.
of the shifter console or on the dashboard face. Leave at least 6mm space behind the mounting location for LED housing. Once a suitable location is chosen, drill a 6mm hole. Run the LED wires through the hole then press the 2 pin LED housing into place. Route the LED wires to the control module. 5 PIN WIRE HARNESS: RED / WHITE WIRE –PARKING LIGHT RELAY INPUT — The RED/WHITE wire is the input to the flashing parking light relay.
- ORANGE :STARTER INTERRUPT O/P RELAY REQUIRED YELLOW / IGNITION INPUT (+) GREEN / (-) DOOR TRIGGER INPUT BLUE / (-) INSTANT TRIGGER INPUT ( HOOD, TRUNK) VIOLET / (+) DOOR TRIGGER INPUT WHITE / DOME LIGHT (OR CH#4 O/P) RELAY REQUIRED BROWN/ WHITE / (-) HORN OUTPUT. Gray wire – (-) 200mA Channel 3 (Trunk) Output – on transmitter for two seconds, the current This will become a 1 second pulse ground by activate (button 3) capacity of this wire is 200 mA.
Brown / White wire wire – (-) 200mA Programmable Output Horn Output – This wire is provided to use the existing vehicle's horn as the alarm system's optional's warning audible device. It's a transistorized low current output, and should only be connected to the low current ground output from the vehicle's horn switch. When the system is triggered, the horn will sound.
2 STEP DOOR UNLOCK WIRE CONNECTION FOR 5 WIRE ALTERNATING DOOR LOCKS H2/13: 22-Pin Plug From Alarm + 12V OEM Door Master Lock 87 86 Pink Wire 85 87a 30 Green Wire +12V Unlock Lock Cut the Unlock Wire x 85 Red +12V X 87 87a Cut the Existing Lock Wire 30 86 H9: 3 Pin Plug To Alarm 85 OEM Slave Door Lock Switch 30 87 87a Unlock 86 Lock +12V Blue Wire OEM Driver’s Door Lock Motor X To All Other Door Lock Motors Cut Existing Unlock 2 STEP DOOR UNLOCK WIRE CONNECTION FOR 2 STEP D
2. Push the Valet switch 3 times (holding in on the 3rd push) until one long chirp is heard, then release the valet switch. You are now in the Alarm feature “A” programming mode. 3. Press and release the transmitter button corresponding to the feature you want to program. a. The siren chirps and LED pause will indicate previously setting. b. The factory default settings is always [1] LED flash, [1] chirp. 4 Depress the transmitter button to change the feature.
Press Transmitter Button 1 2 3 4 One Chirp / LED one pulse Factory Default Setting Pathway Illumination Feature “off” Two Chirps / LED two pulses Three Chirps / LED three pulses Parking light turns “on” for 30- second upon an unlock signal Parking light turns “on” for 30second upon an unlock signal & 10-second upon a lock signal. Ignition controlled door locks & unlocks 0.
3. Press and hold button for 2 seconds. One long siren chirp will indicate the unit is ready to accept adjustments of the shock sensor. 4. Press button on the transmitter once. This will decrease sensitivity level by one. Each time the button is pushed and a decrease is made the siren/horn chirp will respond with [1] chirp. Two chirps indicate the minimum sensitivity. Warn away & full trigger will be deleted when minimum sensitivity is selected 5. Press button on the transmitter once.
serviced or installed, altered, dropped or damaged by water, contrary to the Encore OPERATIONS MANUAL. Or, if used with accessories not approved by Encore, which may have contributed to the defect. See note below regarding product installation**. 4. The purchaser’s remedies under this WARRANTY shall be limited to the repair or replacement of electronic components only.
Notes : E3 IN REV.
