Daim Ntawv Qhia Tus Neeg Siv

ManualsBrandsEncoder ManualsSDIEncoder NDI Wired Video Encoder

Table Of Contents

NDI discovery and connection

It is compatible with NewTek NDI . When the device is in the

same network as the Studio Monitor software(others like OBS,

vMix, etc.), the device can be automatically discovered.

Mo dif y NDI c han ne l n am e

NDI|HX driver installation

Currently our encoders adopt compressed NewTek NDI|HX

technology. Before your using, clients need to download NDI

NDI|HX driver from https://www.newtek.com/ndi/tools/#.

NOTE:

Encoder temporarily does not

support RTSP pull.When NDI is

connected, the default RTSP

channel of the main stream of

the encoder is encrypted, and

the direct pull-out will be

displayed as a mosaic state.

A NDI|HX driver is required to

install before streaming.

When there are several NDI

encoders in the same network,

as default Channel is the same,

clients needs to set different

Channels for different devices.

Restore factory settings

On the dashboard, there is button of Pressing on RESET button for 5 seconds,

device will restore factory settings. Restoring factory setting will lead to the device

hard restart, restarting course will last 1 minute.

Restore factory settings

Two methods for restoring factory settings:

①Via the WEB interface, "Basic Setup > restore factory settings" function;

②Through RESET button:

If users change parameters that lead encoder couldn’t work (typical situation is to

change network address, so that it couldn’t be visited encoder by network.),

users could restore factory setting to default value.

after restoring factory setting, below parameters will be turned to default value:

NOTE:

●Login password will be as admin;

●IP address will be restored as 192.168.1.168, subnet mask will be 255.255.255.0;

●All encoding parameters of video and audio will be restored to factory default value;

●Media transmission parameters will be restored as factory default value.

Quick Reset and reboot

"Quick Reset" is quickly reset the video encoding function of encoder. When

the video signal instability or improper parameter setting cause the encoder

does not work, try to set the device quickly reset. The quickly reset probably

need to wait 3 seconds or so.

“Reboot” is for encoder performs a warm reboot, when the encoder still does

not work after quick reset, please try to reboot the device. Device rebooting

lasts around 20s.

NOTE:

Se le ct” Qu ic k Re se t”, cu rr ent en co di n g w ill be s us pe nd e d f or a w hi le .

Se le ct” Re bo ot ’ ,t he e nc od er w il l wa rm r eb oo t.

Un de r s om e ci rc um st a nc es , re bo ot m ay b e wi th t he h el p o f c o ld re bo ot:

po we r d ow n th en p ow er u p th e de vi ce .

Quick reset and reboot

Take YouTube for an example

“Streaming point” is RTMP address given by platform ( Take YouTube as an example ).

( Other platforms are similar, if questions please contact platform technical support for help ).

RTMP push-flow must first get a push-flow URL address from the platform

Streaming point should be like Server URL+Stream name/key,

for example: rtmp://a.rtmp.youtube.com/live2/9ja6-9u28-uz4j-8x6r

After you get the RTMP URL address, you need to set it up in the encoder.

If the platform requires user name and password verification, you also need

to fill in the corresponding parameters in the encoder.

In the case of rtmps push mode, fill in rtmps URL at Push point and set Use

old RTMP version to yes, so that it can be supported.

NOTE:

Firmware upgrading

The encoder supports online firmware upgrading.

Through the “Basic Settings-Firmware Upgrade” of the web

management interface, you can upload the firmware online.

NOTE:

1: T he d ev ic e w il l r est ar t a u to ma ti ca ll y af te r up gr ad ed , a nd re co ve r to

th e de fa ul t se tt in gs .U ser ca n u p gr ad e th e s of t wa re ve rs io n of d ev ic e.

Cl ic k “B ro ws e” t o se le ct t he up gr ad e fi le , an d cl ic k to up gr ad e th e de vi ce .

Th e up gr ad e pr oc es s is s lo w, a ro un d 30 s to 1 se co nd , pl ea se b e p ati en t.

2: A ft er f in is h u pg ra di ng , ch ec k wh et he r th e ve rs io n in fo rm at io n of t he

la te st f ir mw ar e i s c on si s te nt w it h t he e xp ec t ed st at us t hr ou gh t he S ys te m

St at us -S oft wa re Ver si on o f t he w eb i nt er fa ce .

Upgrading diagram

RTMP Live Streaming

Add streaming service

Add RTMP pushing streaming service

Our device’s H.264 main/sub stream supports adding up to 8 same or different

streaming media service, to meet your needs of adopting same/different stream

media protocols for multi-goal pushing.

On the management interface of “Encoding&Stream-Encoding and Stream

Settings”, for main/sub stream to choose “add one stream service”, users can

add the needed service type.

Currently main video live streaming platforms require”RTMP” service. After adding

RTMP pushing service, click set icon to configure RTMP parameters.

NOTE:

Th is i s an e xa mp le o f RTM P t o i n tr od uc e th e co nf ig ur a ti on o f pu sh

fl ow. O th er p us h fl ow m et ho d s c a n b e l og in t o th e de vi ce p ag e fo r de ta ile d

co nf igu ra ti on .

Device login and network

configuration

If login for the first time, please use Failsafe IP address

You can access http://192.168.1.168, to login the web console.

L o g i n u s e r n a m e a d m i n a d m i n p a s s w o r d

Default IP address and web login

The Failsafe IP address is with subnet mask192.168.1.168 255.255.255.0.

Normally, you don't need to modify this IP address.

IP address configuration

After login, you can configure the IP according to the network, the IP will be

use for pushing and device management. You can configure it to manually

set the IP or DHCP.( Default set is DHCP )