Premium Vinyl Privacy Screen 48" W x 48" H 60 min Approximate assembly time for 2 screens Scan the QR code for an assembly video ASSEMBLY INSTRUCTIONS ZP19014 www.encloscreens.com VER.
ZP19014 ASSEMBLY INSTRUCTIONS GENERAL INFORMATION IMPORTANT j Check the inside of the larger pieces in your box for other materials packed inside. j When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. j We recommend an area approximately 5’x 8’ for unobstructed assembling. j You should not need to use excessive force when assembling components.
ASSEMBLY INSTRUCTIONS ZP19014 Detailed Product Dimensions & Specifications Ground 48 in 48 in 46 in 12 in 2 in 48 in www.encloscreens.
ZP19014 ASSEMBLY INSTRUCTIONS STEP 1: LAY OUT MATERIALS A Post Cap (3) B Left Post (1) 3" x 3" x 47½" C Center Post (1) 3” x 3” x 47½” D Right Post (1) 3” x 3” x 47½” E F Board Wall (8) ⅞" x 11" x 44" Ground Stake (2) G 2½” Self-Drilling Stainless Steel Screw (10) 4 www.encloscreens.
ASSEMBLY INSTRUCTIONS ZP19014 STEP 2: ASSEMBLE FULL PANEL STEP 2.1 b Identify the Left Post (B) and Center Post (C) as illustrated. With a helper, slide a Board Wall (E) down the grooves until the board wall hits the factory installed screws (roughly 2" from the bottom). E Center Post will have four pre-drilled holes at one corner and two factory installed screws at the bottom. B C Left Post will have two pre-drilled holes at one corner and one factory installed screw at the bottom.
ZP19014 STEP 2.3 ASSEMBLY INSTRUCTIONS STEP 2.4 D b Add three more board walls, and fasten the top board wall into the left and center posts as illustrated. b Repeat steps 2.1 through 2.3 with the center post and Right Post (D) for the second panel as shown. STEP 3: INSTALL SCREEN INTO THE GROUND STEP 3.1 b With a helper, move the entire screen to the intended position, Then use a claw hammer to loosen first 6 to 8 inches of hard packed soil as illustrated. Add water to loosen soil as necessary.
ASSEMBLY INSTRUCTIONS ZP19014 STEP 3.3 b Using a piece of 2x4 (or equivalent), attempt to manually push the ground stake 12" into the ground. You can also lightly tap the top of the stake or the top of the 2x4 with a hammer. Repeat for the other ground stake. STEP 3.4 b Fasten both ground stakes to the left and right posts using the pre-drilled holes and the (2) 21/2" self-drilling stainless steel screws. www.encloscreens.
ZP19014 ASSEMBLY INSTRUCTIONS STEP 3.5 b Optional in hard ground: If your ground is too hard, or you have more than 3 or 4 panels to install, please consider these options: b 1. Use a 1¾” diameter auger bit (commonly used for planting tulips) as illustrated b $15-$20 on Amazon.com). b 2. Drill a hole about 12” to 16” deep at the desired location, and fill the holes b with water as illustrated. b 3. Push the panel posts into the holes. 1 2 8 3 www.encloscreens.
ASSEMBLY INSTRUCTIONS ZP19014 ALTERNATIVE STEP 3: MOUNT TO PRE-EXISTING CONCRETE OR WOOD SURFACE b Use galvanized steel L brackets as illustrated. Purchase both brackets and necessary hardware for mounting to a concrete or wood surface from your local hardware store. Concrete screws or wood screws (NOT INCLUDED) Galvanized L brackets (NOT INCLUDED) www.encloscreens.
ZP19014 ASSEMBLY INSTRUCTIONS STEP 4: INSTALL POST CAPS STEP 4.1 b Finish the assembly by pushing the Post Caps (A) down over the top of the posts as illustrated. A 10 www.encloscreens.
www.encloscreens.com support@encloscreens.com 704-892-5222 877-234-6196 6935 Reames Rd. Ste. K. Charlotte, NC 28216 ASSEMBLY INSTRUCTIONS ZP19014 VER.
