Wilmington Screen Kit 36" W x 45" H 45 min Approximate assembly time Scan the QR code for an assembly video ASSEMBLY INSTRUCTIONS ZP19008 www.encloscreens.com VER.
ZP19008 ASSEMBLY INSTRUCTIONS GENERAL INFORMATION IMPORTANT k Check the inside of the larger pieces in your box for other materials packed inside. k When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. k We recommend an area approximately 5’x 8’ for unobstructed assembling. k You should not need to use excessive force when assembling components.
ASSEMBLY INSTRUCTIONS ZP19008 Detailed Product Dimensions & Specifications 36 1/2 in 1 in 45 1/2 in 43 in 2 5/8 in 33 3/8 in www.encloscreens.
ZP19008 ASSEMBLY INSTRUCTIONS STEP 1: LAY OUT MATERIALS A H Post Cap (4) B C Joiner Clip (4) I ¾" Self-Tapping Stainless Steel Screw (24) Bag A Picket (28) ¼" x 1¼" x 40" Post (4) ⅞" x 1½" x 44" D J E 1" Self-Drilling Stainless Steel Screw (8) Bag B Middle Rail (2) 1½" x 1½" x 36½" Top and Bottom Rail (4) 1½" x 1½" x 36½" F G Post Anchor (4) ¾" x 1¼" x 16" 4 K Rail End Cap (12) (6 installed, 6 loose) 1/8" Steel Drill Bit (1) www.encloscreens.
ASSEMBLY INSTRUCTIONS ZP19008 STEP 2: ASSEMBLE SCREEN FRAME Identify the Top and Bottom Rails (D) and Middle Rails (E). Pressure fit the three loose Rail End Caps (G) into the ends of each rail. STEP 2.1 D G E D Note: Top and Bottom Rails only have picket holes on one side. STEP 2.2 STEP 2.4 C B Position the two Posts (B) as illustrated, and slide the top and middle rails down over the posts (towards the locking tabs). STEP 2.
ZP19008 ASSEMBLY INSTRUCTIONS STEP 3: FINISH ASSEMBLING SCREEN STEP 3.1 STEP 3.2 Slide the bottom rail down over the bottom of the posts, aligning the pre-drilled holes on the bottom rail with the pre-drilled holes in the posts. Insert each picket into the bottom rail. 1. Slide the Post Anchors (F) 6" into the bottom of the post. 10" of post anchor should be visible. 2. Use the 1/8" Drill Bit (K) to drill (4) total holes in the post anchor through the pre-drilled holes in the bottom rail. 3.
ASSEMBLY INSTRUCTIONS ZP19008 STEP 3.3 Repeat steps 1 through 3 for your second screen. STEP 4: ASSEMBLE SCREEN FRAME STEP 4.1 Move the screen to its final location, and identify the location of posts. www.encloscreens.com STEP 4.2 Attempt to push the unit into the ground as illustrated. All 10" of the post anchors should be inserted into the ground, so that they are no longer visible.
ZP19008 ASSEMBLY INSTRUCTIONS STEP 4.3 1. Loosen the top 6” or 7” of the ground with a claw hammer as illustrated. 2. Add water to loosened soil. 3. Use a block of wood to protect the top of post, and gently hammer the post into the ground. 2 1 3 Block of wood 8 www.encloscreens.
ASSEMBLY INSTRUCTIONS ZP19008 STEP 4.4 Optional in hard ground: If your ground is too hard, or you have more than 3 or 4 panels to install, please consider these options: 1. Use a 1¾” diameter auger bit (commonly used for planting tulips) as illustrated ($15-$20 on Amazon.com). 2. Drill a hole about 12” to 16” deep at the desired location, and fill the holes with water as illustrated. 3. Push the panel posts into the holes. 1 2 www.encloscreens.
ZP19008 ASSEMBLY INSTRUCTIONS STEP 4.5 Level the screen as necessary, and backfill excavated dirt. Level STEP 4.6 If your ground is really hard, you may need to dig a hole large enough to accommodate one post from each panel into the same hole Approximately 8” in diameter and 10” deep. Backfill and compact the dirt. 10 www.encloscreens.
ASSEMBLY INSTRUCTIONS ZP19008 STEP 5: FASTEN JOINER CLIPS STEP 5.1 Fasten screens together with Joiner Clips (H) using the 1" SelfDrilling Stainless Steel Screws (J) as illustrated. J H 45° degree application www.encloscreens.
ZP19008 ASSEMBLY INSTRUCTIONS STEP 6: FASTEN POST CAPS STEP 6.1 Push the Post Caps (A) down over the posts to lock into place. A 12 www.encloscreens.
www.encloscreens.com support@encloscreens.com 704-892-5222 877-234-6196 6935 Reames Rd. Ste. K. Charlotte, NC 28216 ASSEMBLY INSTRUCTIONS ZP19008 VER.
