Vienna WoodTek Vinyl Privacy Screen Kit 40"W X 48"H 90 min Approximate assembly time for 2 panels Scan the QR code for an assembly video ASSEMBLY INSTRUCTIONS www.encloscreens.com EC18017 (CEDAR COLOR) EC18018 (CHARCOAL COLOR) VER.
EC18017 / EC18018 GENERAL INFORMATION ASSEMBLY INSTRUCTIONS IMPORTANT j Check the inside of the larger pieces in your box for other materials packed inside. j When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. j We recommend an area approximately 5’x 8’ for unobstructed assembling. j You should not need to use excessive force when assembling components.
ASSEMBLY INSTRUCTIONS EC18017 / EC18018 Detailed Product Dimensions & Specifications 40.187in .397in .750in 48.063in 14.000in www.encloscreens.com 1.
EC18017 / EC18018 ASSEMBLY INSTRUCTIONS STEP 1: INSPECT PARTS STEP 1.1 Check the inside of the larger pieces in your box for other materials packed inside. Tools required for a smoother installation experience. * - May be needed depending on soil condition Drill with Philips bit Mallet* Small Wood Block* OPTIONAL 11/2" Tulip Auger* 4 Level www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18017 / EC18018 STEP 2: LAY OUT MATERIALS A Post A (2) 11/8" x 11/8" x 48" D B Post B (2) 11/8" x 11/8" x 48" 1" Black Stainless Steel Screw (16) Rail (4) 3/8" x 1" x 40" E F Ground Stake (4) 1" x 1" x 20" Wide Board (4) 3/8" x 10" x 40" Narrow Board (12) 3/8" x 27/8" x 40" G C H I Spacer (32) Joiner Clip (2) J K Post Cap (4) 1/8" Steel Drill Bit (1) www.encloscreens.
EC18017 / EC18018 ASSEMBLY INSTRUCTIONS STEP 3: ASSEMBLING THE FIRST PANEL STEP 3.1 Position (1) Post (A) and (1) Post (B) so the pre-drilled holes for both posts face forward and the open channels face towards each other as shown. It is recommended to assemble your panels on a flat smooth surface. B Note: This will be the bottom of the screen A STEP 3.2 1. Slide (1) Rail (C) into the post channels until the pre-drilled holes in the rail and the single holes at the tops of the posts align. 2.
ASSEMBLY INSTRUCTIONS EC18017 / EC18018 STEP 3.3 1. Insert (1) Spacer (H) into each post as shown below. Slide the spacer until it hits the installed rail. 2. Insert (1) Narrow Board (D) into the post channels until it hits the spacers. 2 1 H D STEP 3.4 Follow the same process in STEP 3.3 with (5) additional narrow boards and (2) Wide Boards (E) in the pattern shown below. Ensure there is a spacer between each board. E www.encloscreens.
EC18017 / EC18018 ASSEMBLY INSTRUCTIONS STEP 3.5 1. Insert (2) Ground Stakes (F) up the post until the lower pre-drilled holes in the anchors align with the lowest pre-drilled hole in the posts. 2. Drive (2) total 1” black steel screws into the upper predrilled holes in the posts as shown below. 1 Align 2 F STEP 3.6 5.3 1. Insert (1) rail up the posts until the predrilled holes in the rail align with the lowest pre-drilled hole in the posts. 2.
ASSEMBLY INSTRUCTIONS EC18017 / EC18018 STEP 4: ASSEMBLE SECOND PANEL STEP 4.1 Repeat steps 3.1-3.6 to assemble the second screen. STEP 5: INSTALL SCREENS IN THE GROUND STEP 5.1 1. Move the screen to its final location and identify the locations of the posts. 2. Attempt to push the unit into the ground. All 14” of ground stake should go into the ground. 3. Ensure the unit is properly leveled. www.encloscreens.
EC18017 / EC18018 ASSEMBLY INSTRUCTIONS STEP 5.2 Optional in hard ground: 1. Use a 1¾” diameter auger bit (commonly used for planting tulips) as illustrated. 2. Add water to the loosened soil. 3. Use a block of wood to protect the top of the post and gently hammer the post into the ground. 1 2 10 3 www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18017 / EC18018 STEP6: CONNECTING THE PANELS STEP 6.1 1. Straight Line Application: Connect the screens as shown below using the Joiner Clips (I) and (4) 1" black stainless steel screws. 2. Corner Application: Connect the screens as shown below using the Joiner Clips (I) and (4) 1" black stainless steel screws. Tip: For easier install, use 1/8" Drill bit (K) to pre-drill into the post through the holes in the joiner clips 1 K I 2 I K www.encloscreens.
EC18017 / EC18018 ASSEMBLY INSTRUCTIONS STEP 7: INSTALL POST CAPS STEP 7.1 Insert the Post Caps (J) over the tops of the posts to complete the assembly. J 12 www.encloscreens.
www.encloscreens.com support@encloscreens.com 704-892-5222 877-234-6196 6935 Reames Rd. Ste. K. Charlotte, NC 28216 ASSEMBLY INSTRUCTIONS EC18017 (CEDAR COLOR) EC18018 (CHARCOAL COLOR) VER.
