60 min Approximate assembly time for 2 panels Scan the QR code Fresno Screen Kit (2 PACK) for an assembly video ASSEMBLY INSTRUCTIONS www.encloscreens.com EC18014 (CEDAR COLOR) EC18015 (CHARCOAL COLOR) VER.
EC18014 / EC18015 ASSEMBLY INSTRUCTIONS GENERAL INFORMATION IMPORTANT j j j j MISSING OR DAMAGED PARTS? Check the inside of the larger pieces in your box for other materials packed inside. When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. We recommend an area approximately 5’x 8’ for unobstructed assembling. You should not need to use excessive force when assembling components.
ASSEMBLY INSTRUCTIONS EC18014 / EC18015 Detailed Product Dimensions & Specifications www.encloscreens.com 4.6 in 4.0 in 11.1 in 48.0 in 0.9 in 63.
EC18014 / EC18015 ASSEMBLY INSTRUCTIONS STEP 1: INSPECT PARTS STEP 1.1 Check the inside of the larger pieces in your box for other materials packed inside. 4 www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18014 / EC18015 STEP 2: LAY OUT MATERIALS A B C H Rail End Cap (8) 4 installed; 4 loose Thin Slat (10) 1/4" x 11/4" x 62" Square Slat (10) 5/8" x 5/8" x 62" Wide Slat (12) 3/8" x 27/8" x 62" I E D Joiner Clip (4) J Middle Post (2) 5/8" x 1" x 52 1/2" End Post (4) 7/8" x 1 1/2" x 59" G F NOTE: Top rail has large cut holes on one side only Top Rail (2) 11/2" x 11/2" x 631/4" www.encloscreens.
EC18014 / EC18015 ASSEMBLY INSTRUCTIONS STEP 3: ASSEMBLE FIRST PANEL STEP 3.1 1. Slide (6) Wide Slats (C), (5) Square Slats (B), and (5) Thin Slats (A) into the routed holes in one of the End Posts (E). 2. Slide the Middle Post (D) over the slats until it sits in the middle of the slats as shown. 3. Slide a second end post over the slats. NOTE: Ensure all slats are pushed tightly up to the back wall of the posts. E 1 C B A 2 D 3 6 www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18014 / EC18015 STEP 3.2 1. Slide the Bottom Rail (G) over the bottoms of the posts until the pre-drilled holes in the (3) posts and the bottom rail align. 2. Drive (3) total ¾” self-drilling steel screws into the pre-drilled holes in the bottom rail. 1 Align 2 G www.encloscreens.
EC18014 / EC18015 ASSEMBLY INSTRUCTIONS STEP 3.3 1. Slide the Top Rail (F) over the tops of the posts until the pre-drilled holes in the posts and the top rail align. 2. Drive (3) total ¾” Self-Drilling Screws (J) into the pre-drilled holes in the top rail. J 1 Align Align Align 2 F 8 www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18014 / EC18015 STEP 3.4 Turn the panel to the other side and drive (6) total 3/4" self-drilling steel screws through the pre-drilled holes in the top and bottom rail. www.encloscreens.
EC18014 / EC18015 ASSEMBLY INSTRUCTIONS STEP 3.5 Insert (2) Rail End Caps (H) into the ends of the rails. H STEP 4: ASSEMBLE SECOND PANEL STEP 4.1 Repeat Steps 2-3 to assemble the second panel. 10 www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18014 / EC18015 STEP 5: INSTALL IN THE GROUND STEP 5.1 1. Move the screen to its final location. 2. Attempt to push the panel into the ground. 3. Ensure the unit is properly level in both directions as you push it into the ground. NOTE: It is highly recommended to use 2 people for this portion of the installation. STEP 5.2 If your panel cannot be pushed into the ground, follow these steps: 1. Loosen the top 6" of the ground with a claw hammer. 2. Add water to loosened soil. 3.
EC18014 / EC18015 ASSEMBLY INSTRUCTIONS STEP 5.3 Optional in hard ground: If your ground is too hard, or you have more than 3 or 4 panels to install, please consider these options: 1. Use a 1¾” diameter auger bit (commonly used for planting tulips) as illustrated ($15-$20 on Amazon.com). 2. Drill a hole about 12” to 16” deep at the desired location, and fill the holes with water as illustrated. 3. Push the panel posts into the holes. 1 2 3 12 www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18014 / EC18015 STEP 6: CONNECTING THE PANELS STEP 6.1 1. Corner Application: Install the Joiner Clips (I) as shown below. 2. Straight Line Application: Install the Joiner Clips (I) as shown below. 1 I I 2 I I www.encloscreens.
www.encloscreens.com support@encloscreens.com 704-892-5222 877-234-6196 6935 Reames Rd. Ste. K. Charlotte, NC 28216 ASSEMBLY INSTRUCTIONS EC18014 (CEDAR COLOR) EC18015 (CHARCOAL COLOR) VER.
