Florence Screen Kit W/ Planter Box 45 min Approximate assembly time for 1 screen Scan the QR code for an assembly video ASSEMBLY INSTRUCTIONS www.encloscreens.com EC18006 (CEDAR COLOR) EC18007 (ASH COLOR) VER.
EC18006 / EC18007 ASSEMBLY INSTRUCTIONS GENERAL INFORMATION IMPORTANT j j j j MISSING OR DAMAGED PARTS? Check the inside of the larger pieces in your box for other materials packed inside. When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. We recommend an area approximately 5’x 8’ for unobstructed assembling. You should not need to use excessive force when assembling components.
ASSEMBLY INSTRUCTIONS EC18006 / EC18007 Detailed Product Dimensions & Specifications Note: For best plant growth, it is recommended to drill (2) 3/4" diameter drainage holes in the floor board roughly 12" apart. 46 in 7 3/4 1/4 in 9 1/2 in 44 in 46 in 11 in 42 3/4 in 44 in 3/4 in 42 1/2 in Note: Planter Box Depth is 8 5/8" when floor is installed Planter Box Volume: qts (1.6 cubic ft) www.encloscreens.
EC18006 / EC18007 ASSEMBLY INSTRUCTIONS STEP 1: LAY OUT MATERIALS A B I Spacer (24) Long Board (2) 7/8" x 11" x 44" Short Board (2) 7/8" x 11" x 7 1/4" C D J Short Floor Support (3) 7/8" x 1 1/2" x 7 1/4" K Floor Board (1) 7/8" x 7 1/4" x 44" Long Floor Support (2) 7/8" x 1 1/2" x 29 1/2" E F Short Post (2) 1 3/4" x 1 3/4" x 11" L Thin Horizontal Slat (8) 7/8" x 1 1/2" x 44" Wide Horizontal Slat (4) 7/8" x 3" x 44" G H Top view 1 1/2" Black Self-Drilling Stainless Steel Screw (8) Top
ASSEMBLY INSTRUCTIONS EC18006 / EC18007 STEP 2: ASSEMBLING BOARDS STEP 2.1 STEP 2.2 1. Lay down (1) Long Board (A) so that the cut grooves face up as shown. 2. Place (1) Long Floor Support (D) at the bottom of the long board. 3. Position the long floor support so it rests in the middle of the long board. 1. Drive (4) 11/2" Black Self-Drilling Stainless Steel Screws (L) into the predrilled holes in the long floor support. 2. Repeat these steps for the second long board.
EC18006 / EC18007 ASSEMBLY INSTRUCTIONS STEP 3: ASSEMBLING THE PLANTER BOX STEP 3.1 b Orient (2) Short Posts (K) as shown, with two post channels facing each other, and two channels facing front. K Top View Tabs 1. (E) Tabs STEP 3.2 Preview 1. Slide (1) long board into the post channels, ensuring that the tabs on the posts align with the grooves in the board. 2. Drive (4) 5/8" black self-drilling stainless steel screws (M) into the predrilled holes in the posts, securing the long board.
ASSEMBLY INSTRUCTIONS EC18006 / EC18007 Preview STEP 3.3 1. Slide (2) Short Boards (B) into the short post channels, ensuring that the board bottoms are flush. 2. Drive (4) 5/8" black self-drilling stainless steel screws into the pre-drilled holes in the sides of the short posts. 2 1 Ensure that boards are flush STEP 4: INSTALLING REAR POSTS STEP 4.1 1. Slide (1) Right Post (G) and (1) Left Post (H) over the short boards so that the partially covered channel on each post faces the front. 2.
EC18006 / EC18007 ASSEMBLY INSTRUCTIONS STEP 5: COMPLETING PLANTER BOX STEP 5.1 1. Slide the second long board into the post channels. Ensure that this board rests flush with the other boards. 2. Drive (4) 5/8" black selfdrilling stainless steel screws into the predrilled holes in the posts. STEP 5.2 Preview 1. Fit (3) Short Floor Supports (J) so that the notches fit over the inner walls of the long floor supports as shown. 2.
ASSEMBLY INSTRUCTIONS EC18006 / EC18007 STEP 6: ASSEMBLE THE SCREEN STEP 6.1 1. Insert (1) Spacer (I) into both the left and right post channel in the orientation shown below. This will create even spacing between the horizontal slats. 2. Slide (1) Thin Horizontal Slat (E) into the post channels. I 1 Preview Orient as shown 2 E www.encloscreens.
EC18006 / EC18007 ASSEMBLY INSTRUCTIONS STEP 6.2 1. Slide (7) additional thin horizontal slats, (4) Wide Horizontal Slats (F) and (11) aluminum spacers into the post channels in the pattern shown below. Spacers should be inserted between each horizontal slat. 2. Drive (2) 5/8" black self-drilling stainless steel screws into the pre-drilled holes in the posts, securing the top horizontal slat. 1 Preview 2 F E E F E E F E E F E 10 www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18006 / EC18007 STEP 7: INSTALL POST CAPS STEP 6.1 b Insert the (2) Corner Post Caps (N) into the holes in the top of the posts to finish the assembly. N www.encloscreens.
www.encloscreens.com support@encloscreens.com 704-892-5222 877-234-6196 6935 Reames Rd. Ste. K. Charlotte, NC 28216 ASSEMBLY INSTRUCTIONS EC18006 (CEDAR COLOR) EC18007 (ASH COLOR) VER.
